Overall: 4839/6551 fields covered

ADC1

0x50000000: Analog-to-Digital Converter

170/170 fields covered. Toggle Registers.

ISR

interrupt and status register

Offset: 0x0, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVF
rw 		AWD3
rw 		AWD2
rw 		AWD1
rw 		JEOS
rw 		JEOC
rw 		OVR
rw 		EOS
rw 		EOC
rw 		EOSMP
rw 		ADRDY
rw
Toggle Fields.

ADRDY

Bit 0: ADRDY.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP

Bit 1: EOSMP.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC

Bit 2: EOC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS

Bit 3: EOS.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR

Bit 4: OVR.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC

Bit 5: JEOC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS

Bit 6: JEOS.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1

Bit 7: AWD1.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: AWD2.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: AWD3.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF

Bit 10: JQOVF.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

IER

interrupt enable register

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVFIE
rw 		AWD3IE
rw 		AWD2IE
rw 		AWD1IE
rw 		JEOSIE
rw 		JEOCIE
rw 		OVRIE
rw 		EOSIE
rw 		EOCIE
rw 		EOSMPIE
rw 		ADRDYIE
rw
Toggle Fields.

ADRDYIE

Bit 0: ADRDYIE.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: EOSMPIE.

Allowed values:
0: Disabled: End of regular conversion sampling phase interrupt disabled
1: Enabled: End of regular conversion sampling phase interrupt enabled

EOCIE

Bit 2: EOCIE.

Allowed values:
0: Disabled: End of regular conversion interrupt disabled
1: Enabled: End of regular conversion interrupt enabled

EOSIE

Bit 3: EOSIE.

Allowed values:
0: Disabled: End of regular sequence interrupt disabled
1: Enabled: End of regular sequence interrupt enabled

OVRIE

Bit 4: OVRIE.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

JEOCIE

Bit 5: JEOCIE.

Allowed values:
0: Disabled: End of injected conversion interrupt disabled
1: Enabled: End of injected conversion interrupt enabled

JEOSIE

Bit 6: JEOSIE.

Allowed values:
0: Disabled: End of injected sequence interrupt disabled
1: Enabled: End of injected sequence interrupt enabled

AWD1IE

Bit 7: AWD1IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: AWD2IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: AWD3IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

JQOVFIE

Bit 10: JQOVFIE.

Allowed values:
0: Disabled: Injected context queue overflow interrupt disabled
1: Enabled: Injected context queue overflow interrupt enabled

CR

control register

Offset: 0x8, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADCAL
rw 		ADCALDIF
rw 		ADVREGEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JADSTP
rw 		ADSTP
rw 		JADSTART
rw 		ADSTART
rw 		ADDIS
rw 		ADEN
rw
Toggle Fields.

ADEN

Bit 0: ADEN.

Allowed values:
1: Enable: Enable ADC

ADDIS

Bit 1: ADDIS.

Allowed values:
0: Disable: Disable ADC conversion and go to power down mode

ADSTART

Bit 2: ADSTART.

Allowed values:
1: Start: Starts conversion of channel

JADSTART

Bit 3: JADSTART.

Allowed values:
1: Start: Starts conversion of channel

ADSTP

Bit 4: ADSTP.

Allowed values:
1: Stop: Stop conversion of channel

JADSTP

Bit 5: JADSTP.

Allowed values:
1: Stop: Stop conversion of channel

ADVREGEN

Bits 28-29: ADVREGEN.

Allowed values:
0: Intermediate: Intermediate state required when moving the ADC voltage regulator between states
1: Enabled: ADC voltage regulator enabled
2: Disabled: ADC voltage regulator disabled

ADCALDIF

Bit 30: ADCALDIF.

Allowed values:
0: SingleEnded: Calibration for single-ended mode
1: Differential: Calibration for differential mode

ADCAL

Bit 31: ADCAL.

Allowed values:
0: Complete: Calibration complete
1: Calibration: Start the calibration of the ADC

CFGR

configuration register

Offset: 0xC, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD1CH
rw 		JAUTO
rw 		JAWD1EN
rw 		AWD1EN
rw 		AWD1SGL
rw 		JQM
rw 		JDISCEN
rw 		DISCNUM
rw 		DISCEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AUTDLY
rw 		CONT
rw 		OVRMOD
rw 		EXTEN
rw 		EXTSEL
rw 		ALIGN
rw 		RES
rw 		DMACFG
rw 		DMAEN
rw
Toggle Fields.

DMAEN

Bit 0: DMAEN.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: DMACFG.

Allowed values:
0: OneShot: DMA One Shot Mode selected
1: Circular: DMA circular mode selected

RES

Bits 3-4: RES.

Allowed values:
0: Bits12: 12-bit
1: Bits10: 10-bit
2: Bits8: 8-bit
3: Bits6: 6-bit

ALIGN

Bit 5: ALIGN.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-9: EXTSEL.

Allowed values:
7: HRTIM_ADCTRG1: HRTIM_ADCTRG1 event
8: HRTIM_ADCTRG3: HRTIM_ADCTRG3 event
0: TIM1_CC1: Timer 1 CC1 event
1: TIM1_CC2: Timer 1 CC2 event
2: TIM1_CC3: Timer 1 CC3 event
3: TIM2_CC2: Timer 2 CC2 event
4: TIM3_TRGO: Timer 3 TRGO event
6: EXTI11: EXTI line 11
9: TIM1_TRGO: Timer 1 TRGO event
10: TIM1_TRGO2: Timer 1 TRGO2 event
11: TIM2_TRGO: Timer 2 TRGO event
13: TIM6_TRGO: Timer 6 TRGO event
14: TIM15_TRGO: Timer 15 TRGO event
15: TIM3_CC4: Timer 3 CC4 event

EXTEN

Bits 10-11: EXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: OVRMOD.

Allowed values:
0: Preserve: Preserve DR register when an overrun is detected
1: Overwrite: Overwrite DR register when an overrun is detected

CONT

Bit 13: CONT.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

AUTDLY

Bit 14: AUTDLY.

Allowed values:
0: Off: Auto delayed conversion mode off
1: On: Auto delayed conversion mode on

DISCEN

Bit 16: DISCEN.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

DISCNUM

Bits 17-19: DISCNUM.

Allowed values: 0-7

JDISCEN

Bit 20: JDISCEN.

Allowed values:
0: Disabled: Discontinuous mode on injected channels disabled
1: Enabled: Discontinuous mode on injected channels enabled

JQM

Bit 21: JQM.

Allowed values:
0: Mode0: JSQR Mode 0: Queue maintains the last written configuration into JSQR
1: Mode1: JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence

AWD1SGL

Bit 22: AWD1SGL.

Allowed values:
0: All: Analog watchdog 1 enabled on all channels
1: Single: Analog watchdog 1 enabled on single channel selected in AWD1CH

AWD1EN

Bit 23: AWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on regular channels
1: Enabled: Analog watchdog 1 enabled on regular channels

JAWD1EN

Bit 24: JAWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on injected channels
1: Enabled: Analog watchdog 1 enabled on injected channels

JAUTO

Bit 25: JAUTO.

Allowed values:
0: Disabled: Automatic injected group conversion disabled
1: Enabled: Automatic injected group conversion enabled

AWD1CH

Bits 26-30: AWDCH1CH.

Allowed values: 0-19

SMPR1

sample time register 1

Offset: 0x14, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMP9
rw 		SMP8
rw 		SMP7
rw 		SMP6
rw 		SMP5
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SMP5
rw 		SMP4
rw 		SMP3
rw 		SMP2
rw 		SMP1
rw
Toggle Fields.

SMP1

Bits 3-5: SMP1.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP2

Bits 6-8: SMP2.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP3

Bits 9-11: SMP3.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP4

Bits 12-14: SMP4.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP5

Bits 15-17: SMP5.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP6

Bits 18-20: SMP6.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP7

Bits 21-23: SMP7.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP8

Bits 24-26: SMP8.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP9

Bits 27-29: SMP9.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMPR2

sample time register 2

Offset: 0x18, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMP18
rw 		SMP17
rw 		SMP16
rw 		SMP15
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SMP15
rw 		SMP14
rw 		SMP13
rw 		SMP12
rw 		SMP11
rw 		SMP10
rw
Toggle Fields.

SMP10

Bits 0-2: SMP10.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP11

Bits 3-5: SMP11.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP12

Bits 6-8: SMP12.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP13

Bits 9-11: SMP13.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP14

Bits 12-14: SMP14.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP15

Bits 15-17: SMP15.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP16

Bits 18-20: SMP16.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP17

Bits 21-23: SMP17.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP18

Bits 24-26: SMP18.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

TR1

watchdog threshold register 1

Offset: 0x20, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT1
rw
Toggle Fields.

LT1

Bits 0-11: LT1.

Allowed values: 0-4095

HT1

Bits 16-27: HT1.

Allowed values: 0-4095

TR2

watchdog threshold register

Offset: 0x24, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT2
rw
Toggle Fields.

LT2

Bits 0-7: LT2.

Allowed values: 0-4095

HT2

Bits 16-23: HT2.

Allowed values: 0-4095

TR3

watchdog threshold register 3

Offset: 0x28, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT3
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT3
rw
Toggle Fields.

LT3

Bits 0-7: LT3.

Allowed values: 0-4095

HT3

Bits 16-23: HT3.

Allowed values: 0-4095

SQR1

regular sequence register 1

Offset: 0x30, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ4
rw 		SQ3
rw 		SQ2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ2
rw 		SQ1
rw 		L
rw
Toggle Fields.

L

Bits 0-3: L3.

Allowed values: 0-15

SQ1

Bits 6-10: SQ1.

Allowed values: 0-19

SQ2

Bits 12-16: SQ2.

Allowed values: 0-19

SQ3

Bits 18-22: SQ3.

Allowed values: 0-19

SQ4

Bits 24-28: SQ4.

Allowed values: 0-19

SQR2

regular sequence register 2

Offset: 0x34, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ9
rw 		SQ8
rw 		SQ7
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ7
rw 		SQ6
rw 		SQ5
rw
Toggle Fields.

SQ5

Bits 0-4: SQ5.

Allowed values: 0-19

SQ6

Bits 6-10: SQ6.

Allowed values: 0-19

SQ7

Bits 12-16: SQ7.

Allowed values: 0-19

SQ8

Bits 18-22: SQ8.

Allowed values: 0-19

SQ9

Bits 24-28: SQ9.

Allowed values: 0-19

SQR3

regular sequence register 3

Offset: 0x38, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ14
rw 		SQ13
rw 		SQ12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ12
rw 		SQ11
rw 		SQ10
rw
Toggle Fields.

SQ10

Bits 0-4: SQ10.

Allowed values: 0-19

SQ11

Bits 6-10: SQ11.

Allowed values: 0-19

SQ12

Bits 12-16: SQ12.

Allowed values: 0-19

SQ13

Bits 18-22: SQ13.

Allowed values: 0-19

SQ14

Bits 24-28: SQ14.

Allowed values: 0-19

SQR4

regular sequence register 4

Offset: 0x3C, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ16
rw 		SQ15
rw
Toggle Fields.

SQ15

Bits 0-4: SQ15.

Allowed values: 0-19

SQ16

Bits 6-10: SQ16.

Allowed values: 0-19

DR

regular Data Register

Offset: 0x40, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA
r
Toggle Fields.

RDATA

Bits 0-15: regularDATA.

JSQR

injected sequence register

Offset: 0x4C, reset: 0x00000000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JSQ4
rw 		JSQ3
rw 		JSQ2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JSQ2
rw 		JSQ1
rw 		JEXTEN
rw 		JEXTSEL
rw 		JL
rw
Toggle Fields.

JL

Bits 0-1: JL.

Allowed values: 0-3

JEXTSEL

Bits 2-5: JEXTSEL.

Allowed values:
9: HRTIM_ADCTRG2: HRTIM_ADCTRG2 event
10: HRTIM_ADCTRG4: HRTIM_ADCTRG4 event

JEXTEN

Bits 6-7: JEXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

JSQ1

Bits 8-12: JSQ1.

Allowed values: 0-19

JSQ2

Bits 14-18: JSQ2.

Allowed values: 0-19

JSQ3

Bits 20-24: JSQ3.

Allowed values: 0-19

JSQ4

Bits 26-30: JSQ4.

Allowed values: 0-19

OFR1

offset register 1

Offset: 0x60, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET1_EN
rw 		OFFSET1_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET1
rw
Toggle Fields.

OFFSET1

Bits 0-11: OFFSET1.

Allowed values: 0-4095

OFFSET1_CH

Bits 26-30: OFFSET1_CH.

Allowed values: 0-31

OFFSET1_EN

Bit 31: OFFSET1_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR2

offset register 2

Offset: 0x64, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET2_EN
rw 		OFFSET2_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET2
rw
Toggle Fields.

OFFSET2

Bits 0-11: OFFSET2.

Allowed values: 0-4095

OFFSET2_CH

Bits 26-30: OFFSET2_CH.

Allowed values: 0-31

OFFSET2_EN

Bit 31: OFFSET2_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR3

offset register 3

Offset: 0x68, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET3_EN
rw 		OFFSET3_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET3
rw
Toggle Fields.

OFFSET3

Bits 0-11: OFFSET3.

Allowed values: 0-4095

OFFSET3_CH

Bits 26-30: OFFSET3_CH.

Allowed values: 0-31

OFFSET3_EN

Bit 31: OFFSET3_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR4

offset register 4

Offset: 0x6C, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET4_EN
rw 		OFFSET4_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET4
rw
Toggle Fields.

OFFSET4

Bits 0-11: OFFSET4.

Allowed values: 0-4095

OFFSET4_CH

Bits 26-30: OFFSET4_CH.

Allowed values: 0-31

OFFSET4_EN

Bit 31: OFFSET4_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

JDR1

injected data register 1

Offset: 0x80, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: JDATA1.

JDR2

injected data register 2

Offset: 0x84, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA2
r
Toggle Fields.

JDATA2

Bits 0-15: JDATA2.

JDR3

injected data register 3

Offset: 0x88, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA3
r
Toggle Fields.

JDATA3

Bits 0-15: JDATA3.

JDR4

injected data register 4

Offset: 0x8C, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA4
r
Toggle Fields.

JDATA4

Bits 0-15: JDATA4.

AWD2CR

Analog Watchdog 2 Configuration Register

Offset: 0xA0, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD2CH17
rw 		AWD2CH16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AWD2CH15
rw 		AWD2CH14
rw 		AWD2CH13
rw 		AWD2CH12
rw 		AWD2CH11
rw 		AWD2CH10
rw 		AWD2CH9
rw 		AWD2CH8
rw 		AWD2CH7
rw 		AWD2CH6
rw 		AWD2CH5
rw 		AWD2CH4
rw 		AWD2CH3
rw 		AWD2CH2
rw 		AWD2CH1
rw 		AWD2CH0
rw
Toggle Fields.

AWD2CH0

Bit 0: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH1

Bit 1: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH2

Bit 2: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH3

Bit 3: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH4

Bit 4: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH5

Bit 5: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH6

Bit 6: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH7

Bit 7: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH8

Bit 8: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH9

Bit 9: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH10

Bit 10: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH11

Bit 11: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH12

Bit 12: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH13

Bit 13: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH14

Bit 14: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH15

Bit 15: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH16

Bit 16: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH17

Bit 17: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CR

Analog Watchdog 3 Configuration Register

Offset: 0xA4, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD3CH17
rw 		AWD3CH16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AWD3CH15
rw 		AWD3CH14
rw 		AWD3CH13
rw 		AWD3CH12
rw 		AWD3CH11
rw 		AWD3CH10
rw 		AWD3CH9
rw 		AWD3CH8
rw 		AWD3CH7
rw 		AWD3CH6
rw 		AWD3CH5
rw 		AWD3CH4
rw 		AWD3CH3
rw 		AWD3CH2
rw 		AWD3CH1
rw 		AWD3CH0
rw
Toggle Fields.

AWD3CH0

Bit 0: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH1

Bit 1: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH2

Bit 2: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH3

Bit 3: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH4

Bit 4: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH5

Bit 5: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH6

Bit 6: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH7

Bit 7: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH8

Bit 8: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH9

Bit 9: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH10

Bit 10: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH11

Bit 11: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH12

Bit 12: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH13

Bit 13: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH14

Bit 14: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH15

Bit 15: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH16

Bit 16: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH17

Bit 17: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

DIFSEL

Differential Mode Selection Register 2

Offset: 0xB0, reset: 0x00000000, access: Unspecified

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DIFSEL_117
N/A 		DIFSEL_116
N/A
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DIFSEL_115
N/A 		DIFSEL_114
N/A 		DIFSEL_113
N/A 		DIFSEL_112
N/A 		DIFSEL_111
N/A 		DIFSEL_110
N/A 		DIFSEL_19
N/A 		DIFSEL_18
N/A 		DIFSEL_17
N/A 		DIFSEL_16
N/A 		DIFSEL_15
N/A 		DIFSEL_14
N/A 		DIFSEL_13
N/A 		DIFSEL_12
N/A 		DIFSEL_11
N/A 		DIFSEL_10
N/A
Toggle Fields.

DIFSEL_10

Bit 0: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_11

Bit 1: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_12

Bit 2: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_13

Bit 3: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_14

Bit 4: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_15

Bit 5: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_16

Bit 6: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_17

Bit 7: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_18

Bit 8: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_19

Bit 9: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_110

Bit 10: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_111

Bit 11: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_112

Bit 12: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_113

Bit 13: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_114

Bit 14: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_115

Bit 15: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_116

Bit 16: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_117

Bit 17: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

CALFACT

Calibration Factors

Offset: 0xB4, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CALFACT_D
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CALFACT_S
rw
Toggle Fields.

CALFACT_S

Bits 0-6: CALFACT_S.

Allowed values: 0-127

CALFACT_D

Bits 16-22: CALFACT_D.

Allowed values: 0-127

ADC1_2

0x50000300: Analog-to-Digital Converter

32/32 fields covered. Toggle Registers.

CSR

ADC Common status register

Offset: 0x0, reset: 0x00000000, access: read-only

22/22 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JQOVF_SLV
r 		AWD3_SLV
r 		AWD2_SLV
r 		AWD1_SLV
r 		JEOS_SLV
r 		JEOC_SLV
r 		OVR_SLV
r 		EOS_SLV
r 		EOC_SLV
r 		EOSMP_SLV
r 		ADRDY_SLV
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVF_MST
r 		AWD3_MST
r 		AWD2_MST
r 		AWD1_MST
r 		JEOS_MST
r 		JEOC_MST
r 		OVR_MST
r 		EOS_MST
r 		EOC_MST
r 		EOSMP_MST
r 		ADDRDY_MST
r
Toggle Fields.

ADDRDY_MST

Bit 0: ADDRDY_MST.

EOSMP_MST

Bit 1: EOSMP_MST.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC_MST

Bit 2: EOC_MST.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS_MST

Bit 3: EOS_MST.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR_MST

Bit 4: OVR_MST.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC_MST

Bit 5: JEOC_MST.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS_MST

Bit 6: JEOS_MST.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1_MST

Bit 7: AWD1_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2_MST

Bit 8: AWD2_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3_MST

Bit 9: AWD3_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF_MST

Bit 10: JQOVF_MST.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

ADRDY_SLV

Bit 16: ADRDY_SLV.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP_SLV

Bit 17: EOSMP_SLV.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC_SLV

Bit 18: End of regular conversion of the slave ADC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS_SLV

Bit 19: End of regular sequence flag of the slave ADC.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR_SLV

Bit 20: Overrun flag of the slave ADC.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC_SLV

Bit 21: End of injected conversion flag of the slave ADC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS_SLV

Bit 22: End of injected sequence flag of the slave ADC.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1_SLV

Bit 23: Analog watchdog 1 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2_SLV

Bit 24: Analog watchdog 2 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3_SLV

Bit 25: Analog watchdog 3 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF_SLV

Bit 26: Injected Context Queue Overflow flag of the slave ADC.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

CCR

ADC common control register

Offset: 0x8, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
VBATEN
rw 		TSEN
rw 		VREFEN
rw 		CKMODE
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MDMA
rw 		DMACFG
rw 		DELAY
rw 		DUAL
rw
Toggle Fields.

DUAL

Bits 0-4: Dual ADC mode selection.

Allowed values:
0: Independent: Independent mode
1: DualRJ: Dual, combined regular simultaneous + injected simultaneous mode
2: DualRA: Dual, combined regular simultaneous + alternate trigger mode
3: DualIJ: Dual, combined interleaved mode + injected simultaneous mode
5: DualJ: Dual, injected simultaneous mode only
6: DualR: Dual, regular simultaneous mode only
7: DualI: Dual, interleaved mode only
9: DualA: Dual, alternate trigger mode only

DELAY

Bits 8-11: Delay between 2 sampling phases.

Allowed values: 0-15

DMACFG

Bit 13: DMA configuration (for multi-ADC mode).

Allowed values:
0: OneShot: DMA one shot mode selected
1: Circulator: DMA circular mode selected

MDMA

Bits 14-15: Direct memory access mode for multi ADC mode.

Allowed values:
0: Disabled: MDMA mode disabled
2: Bits12_10: MDMA mode enabled for 12 and 10-bit resolution
3: Bits8_6: MDMA mode enabled for 8 and 6-bit resolution

CKMODE

Bits 16-17: ADC clock mode.

Allowed values:
0: Asynchronous: Use Kernel Clock adc_ker_ck_input divided by PRESC. Asynchronous to AHB clock
1: SyncDiv1: Use AHB clock rcc_hclk3. In this case rcc_hclk must equal sys_d1cpre_ck
2: SyncDiv2: Use AHB clock rcc_hclk3 divided by 2
3: SyncDiv4: Use AHB clock rcc_hclk3 divided by 4

VREFEN

Bit 22: VREFINT enable.

Allowed values:
0: Disabled: V_REFINT channel disabled
1: Enabled: V_REFINT channel enabled

TSEN

Bit 23: Temperature sensor enable.

Allowed values:
0: Disabled: Temperature sensor channel disabled
1: Enabled: Temperature sensor channel enabled

VBATEN

Bit 24: VBAT enable.

Allowed values:
0: Disabled: V_BAT channel disabled
1: Enabled: V_BAT channel enabled

CDR

ADC common regular data register for dual and triple modes

Offset: 0xC, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RDATA_SLV
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA_MST
r
Toggle Fields.

RDATA_MST

Bits 0-15: Regular data of the master ADC.

RDATA_SLV

Bits 16-31: Regular data of the slave ADC.

ADC2

0x50000100: Analog-to-Digital Converter

170/170 fields covered. Toggle Registers.

ISR

interrupt and status register

Offset: 0x0, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVF
rw 		AWD3
rw 		AWD2
rw 		AWD1
rw 		JEOS
rw 		JEOC
rw 		OVR
rw 		EOS
rw 		EOC
rw 		EOSMP
rw 		ADRDY
rw
Toggle Fields.

ADRDY

Bit 0: ADRDY.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP

Bit 1: EOSMP.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC

Bit 2: EOC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS

Bit 3: EOS.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR

Bit 4: OVR.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC

Bit 5: JEOC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS

Bit 6: JEOS.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1

Bit 7: AWD1.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: AWD2.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: AWD3.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF

Bit 10: JQOVF.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

IER

interrupt enable register

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVFIE
rw 		AWD3IE
rw 		AWD2IE
rw 		AWD1IE
rw 		JEOSIE
rw 		JEOCIE
rw 		OVRIE
rw 		EOSIE
rw 		EOCIE
rw 		EOSMPIE
rw 		ADRDYIE
rw
Toggle Fields.

ADRDYIE

Bit 0: ADRDYIE.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: EOSMPIE.

Allowed values:
0: Disabled: End of regular conversion sampling phase interrupt disabled
1: Enabled: End of regular conversion sampling phase interrupt enabled

EOCIE

Bit 2: EOCIE.

Allowed values:
0: Disabled: End of regular conversion interrupt disabled
1: Enabled: End of regular conversion interrupt enabled

EOSIE

Bit 3: EOSIE.

Allowed values:
0: Disabled: End of regular sequence interrupt disabled
1: Enabled: End of regular sequence interrupt enabled

OVRIE

Bit 4: OVRIE.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

JEOCIE

Bit 5: JEOCIE.

Allowed values:
0: Disabled: End of injected conversion interrupt disabled
1: Enabled: End of injected conversion interrupt enabled

JEOSIE

Bit 6: JEOSIE.

Allowed values:
0: Disabled: End of injected sequence interrupt disabled
1: Enabled: End of injected sequence interrupt enabled

AWD1IE

Bit 7: AWD1IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: AWD2IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: AWD3IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

JQOVFIE

Bit 10: JQOVFIE.

Allowed values:
0: Disabled: Injected context queue overflow interrupt disabled
1: Enabled: Injected context queue overflow interrupt enabled

CR

control register

Offset: 0x8, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADCAL
rw 		ADCALDIF
rw 		ADVREGEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JADSTP
rw 		ADSTP
rw 		JADSTART
rw 		ADSTART
rw 		ADDIS
rw 		ADEN
rw
Toggle Fields.

ADEN

Bit 0: ADEN.

Allowed values:
1: Enable: Enable ADC

ADDIS

Bit 1: ADDIS.

Allowed values:
0: Disable: Disable ADC conversion and go to power down mode

ADSTART

Bit 2: ADSTART.

Allowed values:
1: Start: Starts conversion of channel

JADSTART

Bit 3: JADSTART.

Allowed values:
1: Start: Starts conversion of channel

ADSTP

Bit 4: ADSTP.

Allowed values:
1: Stop: Stop conversion of channel

JADSTP

Bit 5: JADSTP.

Allowed values:
1: Stop: Stop conversion of channel

ADVREGEN

Bits 28-29: ADVREGEN.

Allowed values:
0: Intermediate: Intermediate state required when moving the ADC voltage regulator between states
1: Enabled: ADC voltage regulator enabled
2: Disabled: ADC voltage regulator disabled

ADCALDIF

Bit 30: ADCALDIF.

Allowed values:
0: SingleEnded: Calibration for single-ended mode
1: Differential: Calibration for differential mode

ADCAL

Bit 31: ADCAL.

Allowed values:
0: Complete: Calibration complete
1: Calibration: Start the calibration of the ADC

CFGR

configuration register

Offset: 0xC, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD1CH
rw 		JAUTO
rw 		JAWD1EN
rw 		AWD1EN
rw 		AWD1SGL
rw 		JQM
rw 		JDISCEN
rw 		DISCNUM
rw 		DISCEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AUTDLY
rw 		CONT
rw 		OVRMOD
rw 		EXTEN
rw 		EXTSEL
rw 		ALIGN
rw 		RES
rw 		DMACFG
rw 		DMAEN
rw
Toggle Fields.

DMAEN

Bit 0: DMAEN.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: DMACFG.

Allowed values:
0: OneShot: DMA One Shot Mode selected
1: Circular: DMA circular mode selected

RES

Bits 3-4: RES.

Allowed values:
0: Bits12: 12-bit
1: Bits10: 10-bit
2: Bits8: 8-bit
3: Bits6: 6-bit

ALIGN

Bit 5: ALIGN.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-9: EXTSEL.

Allowed values:
7: HRTIM_ADCTRG1: HRTIM_ADCTRG1 event
8: HRTIM_ADCTRG3: HRTIM_ADCTRG3 event
0: TIM1_CC1: Timer 1 CC1 event
1: TIM1_CC2: Timer 1 CC2 event
2: TIM1_CC3: Timer 1 CC3 event
3: TIM2_CC2: Timer 2 CC2 event
4: TIM3_TRGO: Timer 3 TRGO event
6: EXTI11: EXTI line 11
9: TIM1_TRGO: Timer 1 TRGO event
10: TIM1_TRGO2: Timer 1 TRGO2 event
11: TIM2_TRGO: Timer 2 TRGO event
13: TIM6_TRGO: Timer 6 TRGO event
14: TIM15_TRGO: Timer 15 TRGO event
15: TIM3_CC4: Timer 3 CC4 event

EXTEN

Bits 10-11: EXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: OVRMOD.

Allowed values:
0: Preserve: Preserve DR register when an overrun is detected
1: Overwrite: Overwrite DR register when an overrun is detected

CONT

Bit 13: CONT.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

AUTDLY

Bit 14: AUTDLY.

Allowed values:
0: Off: Auto delayed conversion mode off
1: On: Auto delayed conversion mode on

DISCEN

Bit 16: DISCEN.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

DISCNUM

Bits 17-19: DISCNUM.

Allowed values: 0-7

JDISCEN

Bit 20: JDISCEN.

Allowed values:
0: Disabled: Discontinuous mode on injected channels disabled
1: Enabled: Discontinuous mode on injected channels enabled

JQM

Bit 21: JQM.

Allowed values:
0: Mode0: JSQR Mode 0: Queue maintains the last written configuration into JSQR
1: Mode1: JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence

AWD1SGL

Bit 22: AWD1SGL.

Allowed values:
0: All: Analog watchdog 1 enabled on all channels
1: Single: Analog watchdog 1 enabled on single channel selected in AWD1CH

AWD1EN

Bit 23: AWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on regular channels
1: Enabled: Analog watchdog 1 enabled on regular channels

JAWD1EN

Bit 24: JAWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on injected channels
1: Enabled: Analog watchdog 1 enabled on injected channels

JAUTO

Bit 25: JAUTO.

Allowed values:
0: Disabled: Automatic injected group conversion disabled
1: Enabled: Automatic injected group conversion enabled

AWD1CH

Bits 26-30: AWDCH1CH.

Allowed values: 0-19

SMPR1

sample time register 1

Offset: 0x14, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMP9
rw 		SMP8
rw 		SMP7
rw 		SMP6
rw 		SMP5
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SMP5
rw 		SMP4
rw 		SMP3
rw 		SMP2
rw 		SMP1
rw
Toggle Fields.

SMP1

Bits 3-5: SMP1.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP2

Bits 6-8: SMP2.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP3

Bits 9-11: SMP3.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP4

Bits 12-14: SMP4.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP5

Bits 15-17: SMP5.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP6

Bits 18-20: SMP6.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP7

Bits 21-23: SMP7.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP8

Bits 24-26: SMP8.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP9

Bits 27-29: SMP9.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMPR2

sample time register 2

Offset: 0x18, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMP18
rw 		SMP17
rw 		SMP16
rw 		SMP15
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SMP15
rw 		SMP14
rw 		SMP13
rw 		SMP12
rw 		SMP11
rw 		SMP10
rw
Toggle Fields.

SMP10

Bits 0-2: SMP10.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP11

Bits 3-5: SMP11.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP12

Bits 6-8: SMP12.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP13

Bits 9-11: SMP13.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP14

Bits 12-14: SMP14.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP15

Bits 15-17: SMP15.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP16

Bits 18-20: SMP16.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP17

Bits 21-23: SMP17.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP18

Bits 24-26: SMP18.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

TR1

watchdog threshold register 1

Offset: 0x20, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT1
rw
Toggle Fields.

LT1

Bits 0-11: LT1.

Allowed values: 0-4095

HT1

Bits 16-27: HT1.

Allowed values: 0-4095

TR2

watchdog threshold register

Offset: 0x24, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT2
rw
Toggle Fields.

LT2

Bits 0-7: LT2.

Allowed values: 0-4095

HT2

Bits 16-23: HT2.

Allowed values: 0-4095

TR3

watchdog threshold register 3

Offset: 0x28, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT3
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT3
rw
Toggle Fields.

LT3

Bits 0-7: LT3.

Allowed values: 0-4095

HT3

Bits 16-23: HT3.

Allowed values: 0-4095

SQR1

regular sequence register 1

Offset: 0x30, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ4
rw 		SQ3
rw 		SQ2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ2
rw 		SQ1
rw 		L
rw
Toggle Fields.

L

Bits 0-3: L3.

Allowed values: 0-15

SQ1

Bits 6-10: SQ1.

Allowed values: 0-19

SQ2

Bits 12-16: SQ2.

Allowed values: 0-19

SQ3

Bits 18-22: SQ3.

Allowed values: 0-19

SQ4

Bits 24-28: SQ4.

Allowed values: 0-19

SQR2

regular sequence register 2

Offset: 0x34, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ9
rw 		SQ8
rw 		SQ7
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ7
rw 		SQ6
rw 		SQ5
rw
Toggle Fields.

SQ5

Bits 0-4: SQ5.

Allowed values: 0-19

SQ6

Bits 6-10: SQ6.

Allowed values: 0-19

SQ7

Bits 12-16: SQ7.

Allowed values: 0-19

SQ8

Bits 18-22: SQ8.

Allowed values: 0-19

SQ9

Bits 24-28: SQ9.

Allowed values: 0-19

SQR3

regular sequence register 3

Offset: 0x38, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ14
rw 		SQ13
rw 		SQ12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ12
rw 		SQ11
rw 		SQ10
rw
Toggle Fields.

SQ10

Bits 0-4: SQ10.

Allowed values: 0-19

SQ11

Bits 6-10: SQ11.

Allowed values: 0-19

SQ12

Bits 12-16: SQ12.

Allowed values: 0-19

SQ13

Bits 18-22: SQ13.

Allowed values: 0-19

SQ14

Bits 24-28: SQ14.

Allowed values: 0-19

SQR4

regular sequence register 4

Offset: 0x3C, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ16
rw 		SQ15
rw
Toggle Fields.

SQ15

Bits 0-4: SQ15.

Allowed values: 0-19

SQ16

Bits 6-10: SQ16.

Allowed values: 0-19

DR

regular Data Register

Offset: 0x40, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA
r
Toggle Fields.

RDATA

Bits 0-15: regularDATA.

JSQR

injected sequence register

Offset: 0x4C, reset: 0x00000000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JSQ4
rw 		JSQ3
rw 		JSQ2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JSQ2
rw 		JSQ1
rw 		JEXTEN
rw 		JEXTSEL
rw 		JL
rw
Toggle Fields.

JL

Bits 0-1: JL.

Allowed values: 0-3

JEXTSEL

Bits 2-5: JEXTSEL.

Allowed values:
9: HRTIM_ADCTRG2: HRTIM_ADCTRG2 event
10: HRTIM_ADCTRG4: HRTIM_ADCTRG4 event

JEXTEN

Bits 6-7: JEXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

JSQ1

Bits 8-12: JSQ1.

Allowed values: 0-19

JSQ2

Bits 14-18: JSQ2.

Allowed values: 0-19

JSQ3

Bits 20-24: JSQ3.

Allowed values: 0-19

JSQ4

Bits 26-30: JSQ4.

Allowed values: 0-19

OFR1

offset register 1

Offset: 0x60, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET1_EN
rw 		OFFSET1_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET1
rw
Toggle Fields.

OFFSET1

Bits 0-11: OFFSET1.

Allowed values: 0-4095

OFFSET1_CH

Bits 26-30: OFFSET1_CH.

Allowed values: 0-31

OFFSET1_EN

Bit 31: OFFSET1_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR2

offset register 2

Offset: 0x64, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET2_EN
rw 		OFFSET2_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET2
rw
Toggle Fields.

OFFSET2

Bits 0-11: OFFSET2.

Allowed values: 0-4095

OFFSET2_CH

Bits 26-30: OFFSET2_CH.

Allowed values: 0-31

OFFSET2_EN

Bit 31: OFFSET2_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR3

offset register 3

Offset: 0x68, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET3_EN
rw 		OFFSET3_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET3
rw
Toggle Fields.

OFFSET3

Bits 0-11: OFFSET3.

Allowed values: 0-4095

OFFSET3_CH

Bits 26-30: OFFSET3_CH.

Allowed values: 0-31

OFFSET3_EN

Bit 31: OFFSET3_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR4

offset register 4

Offset: 0x6C, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET4_EN
rw 		OFFSET4_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET4
rw
Toggle Fields.

OFFSET4

Bits 0-11: OFFSET4.

Allowed values: 0-4095

OFFSET4_CH

Bits 26-30: OFFSET4_CH.

Allowed values: 0-31

OFFSET4_EN

Bit 31: OFFSET4_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

JDR1

injected data register 1

Offset: 0x80, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: JDATA1.

JDR2

injected data register 2

Offset: 0x84, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA2
r
Toggle Fields.

JDATA2

Bits 0-15: JDATA2.

JDR3

injected data register 3

Offset: 0x88, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA3
r
Toggle Fields.

JDATA3

Bits 0-15: JDATA3.

JDR4

injected data register 4

Offset: 0x8C, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA4
r
Toggle Fields.

JDATA4

Bits 0-15: JDATA4.

AWD2CR

Analog Watchdog 2 Configuration Register

Offset: 0xA0, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD2CH17
rw 		AWD2CH16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AWD2CH15
rw 		AWD2CH14
rw 		AWD2CH13
rw 		AWD2CH12
rw 		AWD2CH11
rw 		AWD2CH10
rw 		AWD2CH9
rw 		AWD2CH8
rw 		AWD2CH7
rw 		AWD2CH6
rw 		AWD2CH5
rw 		AWD2CH4
rw 		AWD2CH3
rw 		AWD2CH2
rw 		AWD2CH1
rw 		AWD2CH0
rw
Toggle Fields.

AWD2CH0

Bit 0: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH1

Bit 1: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH2

Bit 2: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH3

Bit 3: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH4

Bit 4: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH5

Bit 5: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH6

Bit 6: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH7

Bit 7: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH8

Bit 8: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH9

Bit 9: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH10

Bit 10: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH11

Bit 11: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH12

Bit 12: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH13

Bit 13: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH14

Bit 14: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH15

Bit 15: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH16

Bit 16: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH17

Bit 17: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CR

Analog Watchdog 3 Configuration Register

Offset: 0xA4, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD3CH17
rw 		AWD3CH16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AWD3CH15
rw 		AWD3CH14
rw 		AWD3CH13
rw 		AWD3CH12
rw 		AWD3CH11
rw 		AWD3CH10
rw 		AWD3CH9
rw 		AWD3CH8
rw 		AWD3CH7
rw 		AWD3CH6
rw 		AWD3CH5
rw 		AWD3CH4
rw 		AWD3CH3
rw 		AWD3CH2
rw 		AWD3CH1
rw 		AWD3CH0
rw
Toggle Fields.

AWD3CH0

Bit 0: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH1

Bit 1: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH2

Bit 2: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH3

Bit 3: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH4

Bit 4: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH5

Bit 5: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH6

Bit 6: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH7

Bit 7: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH8

Bit 8: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH9

Bit 9: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH10

Bit 10: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH11

Bit 11: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH12

Bit 12: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH13

Bit 13: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH14

Bit 14: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH15

Bit 15: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH16

Bit 16: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH17

Bit 17: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

DIFSEL

Differential Mode Selection Register 2

Offset: 0xB0, reset: 0x00000000, access: Unspecified

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DIFSEL_117
N/A 		DIFSEL_116
N/A
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DIFSEL_115
N/A 		DIFSEL_114
N/A 		DIFSEL_113
N/A 		DIFSEL_112
N/A 		DIFSEL_111
N/A 		DIFSEL_110
N/A 		DIFSEL_19
N/A 		DIFSEL_18
N/A 		DIFSEL_17
N/A 		DIFSEL_16
N/A 		DIFSEL_15
N/A 		DIFSEL_14
N/A 		DIFSEL_13
N/A 		DIFSEL_12
N/A 		DIFSEL_11
N/A 		DIFSEL_10
N/A
Toggle Fields.

DIFSEL_10

Bit 0: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_11

Bit 1: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_12

Bit 2: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_13

Bit 3: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_14

Bit 4: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_15

Bit 5: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_16

Bit 6: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_17

Bit 7: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_18

Bit 8: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_19

Bit 9: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_110

Bit 10: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_111

Bit 11: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_112

Bit 12: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_113

Bit 13: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_114

Bit 14: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_115

Bit 15: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_116

Bit 16: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_117

Bit 17: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

CALFACT

Calibration Factors

Offset: 0xB4, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CALFACT_D
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CALFACT_S
rw
Toggle Fields.

CALFACT_S

Bits 0-6: CALFACT_S.

Allowed values: 0-127

CALFACT_D

Bits 16-22: CALFACT_D.

Allowed values: 0-127

ADC3

0x50000400: Analog-to-Digital Converter

170/170 fields covered. Toggle Registers.

ISR

interrupt and status register

Offset: 0x0, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVF
rw 		AWD3
rw 		AWD2
rw 		AWD1
rw 		JEOS
rw 		JEOC
rw 		OVR
rw 		EOS
rw 		EOC
rw 		EOSMP
rw 		ADRDY
rw
Toggle Fields.

ADRDY

Bit 0: ADRDY.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP

Bit 1: EOSMP.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC

Bit 2: EOC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS

Bit 3: EOS.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR

Bit 4: OVR.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC

Bit 5: JEOC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS

Bit 6: JEOS.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1

Bit 7: AWD1.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: AWD2.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: AWD3.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF

Bit 10: JQOVF.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

IER

interrupt enable register

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVFIE
rw 		AWD3IE
rw 		AWD2IE
rw 		AWD1IE
rw 		JEOSIE
rw 		JEOCIE
rw 		OVRIE
rw 		EOSIE
rw 		EOCIE
rw 		EOSMPIE
rw 		ADRDYIE
rw
Toggle Fields.

ADRDYIE

Bit 0: ADRDYIE.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: EOSMPIE.

Allowed values:
0: Disabled: End of regular conversion sampling phase interrupt disabled
1: Enabled: End of regular conversion sampling phase interrupt enabled

EOCIE

Bit 2: EOCIE.

Allowed values:
0: Disabled: End of regular conversion interrupt disabled
1: Enabled: End of regular conversion interrupt enabled

EOSIE

Bit 3: EOSIE.

Allowed values:
0: Disabled: End of regular sequence interrupt disabled
1: Enabled: End of regular sequence interrupt enabled

OVRIE

Bit 4: OVRIE.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

JEOCIE

Bit 5: JEOCIE.

Allowed values:
0: Disabled: End of injected conversion interrupt disabled
1: Enabled: End of injected conversion interrupt enabled

JEOSIE

Bit 6: JEOSIE.

Allowed values:
0: Disabled: End of injected sequence interrupt disabled
1: Enabled: End of injected sequence interrupt enabled

AWD1IE

Bit 7: AWD1IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: AWD2IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: AWD3IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

JQOVFIE

Bit 10: JQOVFIE.

Allowed values:
0: Disabled: Injected context queue overflow interrupt disabled
1: Enabled: Injected context queue overflow interrupt enabled

CR

control register

Offset: 0x8, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADCAL
rw 		ADCALDIF
rw 		ADVREGEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JADSTP
rw 		ADSTP
rw 		JADSTART
rw 		ADSTART
rw 		ADDIS
rw 		ADEN
rw
Toggle Fields.

ADEN

Bit 0: ADEN.

Allowed values:
1: Enable: Enable ADC

ADDIS

Bit 1: ADDIS.

Allowed values:
0: Disable: Disable ADC conversion and go to power down mode

ADSTART

Bit 2: ADSTART.

Allowed values:
1: Start: Starts conversion of channel

JADSTART

Bit 3: JADSTART.

Allowed values:
1: Start: Starts conversion of channel

ADSTP

Bit 4: ADSTP.

Allowed values:
1: Stop: Stop conversion of channel

JADSTP

Bit 5: JADSTP.

Allowed values:
1: Stop: Stop conversion of channel

ADVREGEN

Bits 28-29: ADVREGEN.

Allowed values:
0: Intermediate: Intermediate state required when moving the ADC voltage regulator between states
1: Enabled: ADC voltage regulator enabled
2: Disabled: ADC voltage regulator disabled

ADCALDIF

Bit 30: ADCALDIF.

Allowed values:
0: SingleEnded: Calibration for single-ended mode
1: Differential: Calibration for differential mode

ADCAL

Bit 31: ADCAL.

Allowed values:
0: Complete: Calibration complete
1: Calibration: Start the calibration of the ADC

CFGR

configuration register

Offset: 0xC, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD1CH
rw 		JAUTO
rw 		JAWD1EN
rw 		AWD1EN
rw 		AWD1SGL
rw 		JQM
rw 		JDISCEN
rw 		DISCNUM
rw 		DISCEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AUTDLY
rw 		CONT
rw 		OVRMOD
rw 		EXTEN
rw 		EXTSEL
rw 		ALIGN
rw 		RES
rw 		DMACFG
rw 		DMAEN
rw
Toggle Fields.

DMAEN

Bit 0: DMAEN.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: DMACFG.

Allowed values:
0: OneShot: DMA One Shot Mode selected
1: Circular: DMA circular mode selected

RES

Bits 3-4: RES.

Allowed values:
0: Bits12: 12-bit
1: Bits10: 10-bit
2: Bits8: 8-bit
3: Bits6: 6-bit

ALIGN

Bit 5: ALIGN.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-9: EXTSEL.

Allowed values:
7: HRTIM_ADCTRG1: HRTIM_ADCTRG1 event
8: HRTIM_ADCTRG3: HRTIM_ADCTRG3 event
0: TIM1_CC1: Timer 1 CC1 event
1: TIM1_CC2: Timer 1 CC2 event
2: TIM1_CC3: Timer 1 CC3 event
3: TIM2_CC2: Timer 2 CC2 event
4: TIM3_TRGO: Timer 3 TRGO event
6: EXTI11: EXTI line 11
9: TIM1_TRGO: Timer 1 TRGO event
10: TIM1_TRGO2: Timer 1 TRGO2 event
11: TIM2_TRGO: Timer 2 TRGO event
13: TIM6_TRGO: Timer 6 TRGO event
14: TIM15_TRGO: Timer 15 TRGO event
15: TIM3_CC4: Timer 3 CC4 event

EXTEN

Bits 10-11: EXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: OVRMOD.

Allowed values:
0: Preserve: Preserve DR register when an overrun is detected
1: Overwrite: Overwrite DR register when an overrun is detected

CONT

Bit 13: CONT.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

AUTDLY

Bit 14: AUTDLY.

Allowed values:
0: Off: Auto delayed conversion mode off
1: On: Auto delayed conversion mode on

DISCEN

Bit 16: DISCEN.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

DISCNUM

Bits 17-19: DISCNUM.

Allowed values: 0-7

JDISCEN

Bit 20: JDISCEN.

Allowed values:
0: Disabled: Discontinuous mode on injected channels disabled
1: Enabled: Discontinuous mode on injected channels enabled

JQM

Bit 21: JQM.

Allowed values:
0: Mode0: JSQR Mode 0: Queue maintains the last written configuration into JSQR
1: Mode1: JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence

AWD1SGL

Bit 22: AWD1SGL.

Allowed values:
0: All: Analog watchdog 1 enabled on all channels
1: Single: Analog watchdog 1 enabled on single channel selected in AWD1CH

AWD1EN

Bit 23: AWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on regular channels
1: Enabled: Analog watchdog 1 enabled on regular channels

JAWD1EN

Bit 24: JAWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on injected channels
1: Enabled: Analog watchdog 1 enabled on injected channels

JAUTO

Bit 25: JAUTO.

Allowed values:
0: Disabled: Automatic injected group conversion disabled
1: Enabled: Automatic injected group conversion enabled

AWD1CH

Bits 26-30: AWDCH1CH.

Allowed values: 0-19

SMPR1

sample time register 1

Offset: 0x14, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMP9
rw 		SMP8
rw 		SMP7
rw 		SMP6
rw 		SMP5
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SMP5
rw 		SMP4
rw 		SMP3
rw 		SMP2
rw 		SMP1
rw
Toggle Fields.

SMP1

Bits 3-5: SMP1.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP2

Bits 6-8: SMP2.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP3

Bits 9-11: SMP3.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP4

Bits 12-14: SMP4.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP5

Bits 15-17: SMP5.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP6

Bits 18-20: SMP6.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP7

Bits 21-23: SMP7.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP8

Bits 24-26: SMP8.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP9

Bits 27-29: SMP9.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMPR2

sample time register 2

Offset: 0x18, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMP18
rw 		SMP17
rw 		SMP16
rw 		SMP15
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SMP15
rw 		SMP14
rw 		SMP13
rw 		SMP12
rw 		SMP11
rw 		SMP10
rw
Toggle Fields.

SMP10

Bits 0-2: SMP10.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP11

Bits 3-5: SMP11.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP12

Bits 6-8: SMP12.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP13

Bits 9-11: SMP13.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP14

Bits 12-14: SMP14.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP15

Bits 15-17: SMP15.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP16

Bits 18-20: SMP16.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP17

Bits 21-23: SMP17.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP18

Bits 24-26: SMP18.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

TR1

watchdog threshold register 1

Offset: 0x20, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT1
rw
Toggle Fields.

LT1

Bits 0-11: LT1.

Allowed values: 0-4095

HT1

Bits 16-27: HT1.

Allowed values: 0-4095

TR2

watchdog threshold register

Offset: 0x24, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT2
rw
Toggle Fields.

LT2

Bits 0-7: LT2.

Allowed values: 0-4095

HT2

Bits 16-23: HT2.

Allowed values: 0-4095

TR3

watchdog threshold register 3

Offset: 0x28, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT3
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT3
rw
Toggle Fields.

LT3

Bits 0-7: LT3.

Allowed values: 0-4095

HT3

Bits 16-23: HT3.

Allowed values: 0-4095

SQR1

regular sequence register 1

Offset: 0x30, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ4
rw 		SQ3
rw 		SQ2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ2
rw 		SQ1
rw 		L
rw
Toggle Fields.

L

Bits 0-3: L3.

Allowed values: 0-15

SQ1

Bits 6-10: SQ1.

Allowed values: 0-19

SQ2

Bits 12-16: SQ2.

Allowed values: 0-19

SQ3

Bits 18-22: SQ3.

Allowed values: 0-19

SQ4

Bits 24-28: SQ4.

Allowed values: 0-19

SQR2

regular sequence register 2

Offset: 0x34, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ9
rw 		SQ8
rw 		SQ7
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ7
rw 		SQ6
rw 		SQ5
rw
Toggle Fields.

SQ5

Bits 0-4: SQ5.

Allowed values: 0-19

SQ6

Bits 6-10: SQ6.

Allowed values: 0-19

SQ7

Bits 12-16: SQ7.

Allowed values: 0-19

SQ8

Bits 18-22: SQ8.

Allowed values: 0-19

SQ9

Bits 24-28: SQ9.

Allowed values: 0-19

SQR3

regular sequence register 3

Offset: 0x38, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ14
rw 		SQ13
rw 		SQ12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ12
rw 		SQ11
rw 		SQ10
rw
Toggle Fields.

SQ10

Bits 0-4: SQ10.

Allowed values: 0-19

SQ11

Bits 6-10: SQ11.

Allowed values: 0-19

SQ12

Bits 12-16: SQ12.

Allowed values: 0-19

SQ13

Bits 18-22: SQ13.

Allowed values: 0-19

SQ14

Bits 24-28: SQ14.

Allowed values: 0-19

SQR4

regular sequence register 4

Offset: 0x3C, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ16
rw 		SQ15
rw
Toggle Fields.

SQ15

Bits 0-4: SQ15.

Allowed values: 0-19

SQ16

Bits 6-10: SQ16.

Allowed values: 0-19

DR

regular Data Register

Offset: 0x40, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA
r
Toggle Fields.

RDATA

Bits 0-15: regularDATA.

JSQR

injected sequence register

Offset: 0x4C, reset: 0x00000000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JSQ4
rw 		JSQ3
rw 		JSQ2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JSQ2
rw 		JSQ1
rw 		JEXTEN
rw 		JEXTSEL
rw 		JL
rw
Toggle Fields.

JL

Bits 0-1: JL.

Allowed values: 0-3

JEXTSEL

Bits 2-5: JEXTSEL.

Allowed values:
9: HRTIM_ADCTRG2: HRTIM_ADCTRG2 event
10: HRTIM_ADCTRG4: HRTIM_ADCTRG4 event

JEXTEN

Bits 6-7: JEXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

JSQ1

Bits 8-12: JSQ1.

Allowed values: 0-19

JSQ2

Bits 14-18: JSQ2.

Allowed values: 0-19

JSQ3

Bits 20-24: JSQ3.

Allowed values: 0-19

JSQ4

Bits 26-30: JSQ4.

Allowed values: 0-19

OFR1

offset register 1

Offset: 0x60, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET1_EN
rw 		OFFSET1_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET1
rw
Toggle Fields.

OFFSET1

Bits 0-11: OFFSET1.

Allowed values: 0-4095

OFFSET1_CH

Bits 26-30: OFFSET1_CH.

Allowed values: 0-31

OFFSET1_EN

Bit 31: OFFSET1_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR2

offset register 2

Offset: 0x64, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET2_EN
rw 		OFFSET2_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET2
rw
Toggle Fields.

OFFSET2

Bits 0-11: OFFSET2.

Allowed values: 0-4095

OFFSET2_CH

Bits 26-30: OFFSET2_CH.

Allowed values: 0-31

OFFSET2_EN

Bit 31: OFFSET2_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR3

offset register 3

Offset: 0x68, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET3_EN
rw 		OFFSET3_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET3
rw
Toggle Fields.

OFFSET3

Bits 0-11: OFFSET3.

Allowed values: 0-4095

OFFSET3_CH

Bits 26-30: OFFSET3_CH.

Allowed values: 0-31

OFFSET3_EN

Bit 31: OFFSET3_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR4

offset register 4

Offset: 0x6C, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET4_EN
rw 		OFFSET4_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET4
rw
Toggle Fields.

OFFSET4

Bits 0-11: OFFSET4.

Allowed values: 0-4095

OFFSET4_CH

Bits 26-30: OFFSET4_CH.

Allowed values: 0-31

OFFSET4_EN

Bit 31: OFFSET4_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

JDR1

injected data register 1

Offset: 0x80, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: JDATA1.

JDR2

injected data register 2

Offset: 0x84, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA2
r
Toggle Fields.

JDATA2

Bits 0-15: JDATA2.

JDR3

injected data register 3

Offset: 0x88, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA3
r
Toggle Fields.

JDATA3

Bits 0-15: JDATA3.

JDR4

injected data register 4

Offset: 0x8C, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA4
r
Toggle Fields.

JDATA4

Bits 0-15: JDATA4.

AWD2CR

Analog Watchdog 2 Configuration Register

Offset: 0xA0, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD2CH17
rw 		AWD2CH16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AWD2CH15
rw 		AWD2CH14
rw 		AWD2CH13
rw 		AWD2CH12
rw 		AWD2CH11
rw 		AWD2CH10
rw 		AWD2CH9
rw 		AWD2CH8
rw 		AWD2CH7
rw 		AWD2CH6
rw 		AWD2CH5
rw 		AWD2CH4
rw 		AWD2CH3
rw 		AWD2CH2
rw 		AWD2CH1
rw 		AWD2CH0
rw
Toggle Fields.

AWD2CH0

Bit 0: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH1

Bit 1: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH2

Bit 2: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH3

Bit 3: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH4

Bit 4: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH5

Bit 5: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH6

Bit 6: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH7

Bit 7: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH8

Bit 8: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH9

Bit 9: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH10

Bit 10: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH11

Bit 11: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH12

Bit 12: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH13

Bit 13: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH14

Bit 14: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH15

Bit 15: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH16

Bit 16: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH17

Bit 17: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CR

Analog Watchdog 3 Configuration Register

Offset: 0xA4, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD3CH17
rw 		AWD3CH16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AWD3CH15
rw 		AWD3CH14
rw 		AWD3CH13
rw 		AWD3CH12
rw 		AWD3CH11
rw 		AWD3CH10
rw 		AWD3CH9
rw 		AWD3CH8
rw 		AWD3CH7
rw 		AWD3CH6
rw 		AWD3CH5
rw 		AWD3CH4
rw 		AWD3CH3
rw 		AWD3CH2
rw 		AWD3CH1
rw 		AWD3CH0
rw
Toggle Fields.

AWD3CH0

Bit 0: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH1

Bit 1: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH2

Bit 2: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH3

Bit 3: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH4

Bit 4: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH5

Bit 5: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH6

Bit 6: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH7

Bit 7: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH8

Bit 8: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH9

Bit 9: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH10

Bit 10: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH11

Bit 11: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH12

Bit 12: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH13

Bit 13: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH14

Bit 14: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH15

Bit 15: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH16

Bit 16: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH17

Bit 17: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

DIFSEL

Differential Mode Selection Register 2

Offset: 0xB0, reset: 0x00000000, access: Unspecified

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DIFSEL_117
N/A 		DIFSEL_116
N/A
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DIFSEL_115
N/A 		DIFSEL_114
N/A 		DIFSEL_113
N/A 		DIFSEL_112
N/A 		DIFSEL_111
N/A 		DIFSEL_110
N/A 		DIFSEL_19
N/A 		DIFSEL_18
N/A 		DIFSEL_17
N/A 		DIFSEL_16
N/A 		DIFSEL_15
N/A 		DIFSEL_14
N/A 		DIFSEL_13
N/A 		DIFSEL_12
N/A 		DIFSEL_11
N/A 		DIFSEL_10
N/A
Toggle Fields.

DIFSEL_10

Bit 0: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_11

Bit 1: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_12

Bit 2: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_13

Bit 3: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_14

Bit 4: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_15

Bit 5: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_16

Bit 6: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_17

Bit 7: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_18

Bit 8: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_19

Bit 9: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_110

Bit 10: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_111

Bit 11: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_112

Bit 12: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_113

Bit 13: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_114

Bit 14: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_115

Bit 15: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_116

Bit 16: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_117

Bit 17: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

CALFACT

Calibration Factors

Offset: 0xB4, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CALFACT_D
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CALFACT_S
rw
Toggle Fields.

CALFACT_S

Bits 0-6: CALFACT_S.

Allowed values: 0-127

CALFACT_D

Bits 16-22: CALFACT_D.

Allowed values: 0-127

ADC3_4

0x50000700: Analog-to-Digital Converter

32/32 fields covered. Toggle Registers.

CSR

ADC Common status register

Offset: 0x0, reset: 0x00000000, access: read-only

22/22 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JQOVF_SLV
r 		AWD3_SLV
r 		AWD2_SLV
r 		AWD1_SLV
r 		JEOS_SLV
r 		JEOC_SLV
r 		OVR_SLV
r 		EOS_SLV
r 		EOC_SLV
r 		EOSMP_SLV
r 		ADRDY_SLV
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVF_MST
r 		AWD3_MST
r 		AWD2_MST
r 		AWD1_MST
r 		JEOS_MST
r 		JEOC_MST
r 		OVR_MST
r 		EOS_MST
r 		EOC_MST
r 		EOSMP_MST
r 		ADDRDY_MST
r
Toggle Fields.

ADDRDY_MST

Bit 0: ADDRDY_MST.

EOSMP_MST

Bit 1: EOSMP_MST.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC_MST

Bit 2: EOC_MST.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS_MST

Bit 3: EOS_MST.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR_MST

Bit 4: OVR_MST.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC_MST

Bit 5: JEOC_MST.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS_MST

Bit 6: JEOS_MST.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1_MST

Bit 7: AWD1_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2_MST

Bit 8: AWD2_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3_MST

Bit 9: AWD3_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF_MST

Bit 10: JQOVF_MST.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

ADRDY_SLV

Bit 16: ADRDY_SLV.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP_SLV

Bit 17: EOSMP_SLV.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC_SLV

Bit 18: End of regular conversion of the slave ADC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS_SLV

Bit 19: End of regular sequence flag of the slave ADC.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR_SLV

Bit 20: Overrun flag of the slave ADC.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC_SLV

Bit 21: End of injected conversion flag of the slave ADC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS_SLV

Bit 22: End of injected sequence flag of the slave ADC.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1_SLV

Bit 23: Analog watchdog 1 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2_SLV

Bit 24: Analog watchdog 2 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3_SLV

Bit 25: Analog watchdog 3 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF_SLV

Bit 26: Injected Context Queue Overflow flag of the slave ADC.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

CCR

ADC common control register

Offset: 0x8, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
VBATEN
rw 		TSEN
rw 		VREFEN
rw 		CKMODE
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MDMA
rw 		DMACFG
rw 		DELAY
rw 		DUAL
rw
Toggle Fields.

DUAL

Bits 0-4: Dual ADC mode selection.

Allowed values:
0: Independent: Independent mode
1: DualRJ: Dual, combined regular simultaneous + injected simultaneous mode
2: DualRA: Dual, combined regular simultaneous + alternate trigger mode
3: DualIJ: Dual, combined interleaved mode + injected simultaneous mode
5: DualJ: Dual, injected simultaneous mode only
6: DualR: Dual, regular simultaneous mode only
7: DualI: Dual, interleaved mode only
9: DualA: Dual, alternate trigger mode only

DELAY

Bits 8-11: Delay between 2 sampling phases.

Allowed values: 0-15

DMACFG

Bit 13: DMA configuration (for multi-ADC mode).

Allowed values:
0: OneShot: DMA one shot mode selected
1: Circulator: DMA circular mode selected

MDMA

Bits 14-15: Direct memory access mode for multi ADC mode.

Allowed values:
0: Disabled: MDMA mode disabled
2: Bits12_10: MDMA mode enabled for 12 and 10-bit resolution
3: Bits8_6: MDMA mode enabled for 8 and 6-bit resolution

CKMODE

Bits 16-17: ADC clock mode.

Allowed values:
0: Asynchronous: Use Kernel Clock adc_ker_ck_input divided by PRESC. Asynchronous to AHB clock
1: SyncDiv1: Use AHB clock rcc_hclk3. In this case rcc_hclk must equal sys_d1cpre_ck
2: SyncDiv2: Use AHB clock rcc_hclk3 divided by 2
3: SyncDiv4: Use AHB clock rcc_hclk3 divided by 4

VREFEN

Bit 22: VREFINT enable.

Allowed values:
0: Disabled: V_REFINT channel disabled
1: Enabled: V_REFINT channel enabled

TSEN

Bit 23: Temperature sensor enable.

Allowed values:
0: Disabled: Temperature sensor channel disabled
1: Enabled: Temperature sensor channel enabled

VBATEN

Bit 24: VBAT enable.

Allowed values:
0: Disabled: V_BAT channel disabled
1: Enabled: V_BAT channel enabled

CDR

ADC common regular data register for dual and triple modes

Offset: 0xC, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RDATA_SLV
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA_MST
r
Toggle Fields.

RDATA_MST

Bits 0-15: Regular data of the master ADC.

RDATA_SLV

Bits 16-31: Regular data of the slave ADC.

ADC4

0x50000500: Analog-to-Digital Converter

170/170 fields covered. Toggle Registers.

ISR

interrupt and status register

Offset: 0x0, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVF
rw 		AWD3
rw 		AWD2
rw 		AWD1
rw 		JEOS
rw 		JEOC
rw 		OVR
rw 		EOS
rw 		EOC
rw 		EOSMP
rw 		ADRDY
rw
Toggle Fields.

ADRDY

Bit 0: ADRDY.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP

Bit 1: EOSMP.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC

Bit 2: EOC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS

Bit 3: EOS.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR

Bit 4: OVR.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC

Bit 5: JEOC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS

Bit 6: JEOS.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1

Bit 7: AWD1.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: AWD2.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: AWD3.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF

Bit 10: JQOVF.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

IER

interrupt enable register

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JQOVFIE
rw 		AWD3IE
rw 		AWD2IE
rw 		AWD1IE
rw 		JEOSIE
rw 		JEOCIE
rw 		OVRIE
rw 		EOSIE
rw 		EOCIE
rw 		EOSMPIE
rw 		ADRDYIE
rw
Toggle Fields.

ADRDYIE

Bit 0: ADRDYIE.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: EOSMPIE.

Allowed values:
0: Disabled: End of regular conversion sampling phase interrupt disabled
1: Enabled: End of regular conversion sampling phase interrupt enabled

EOCIE

Bit 2: EOCIE.

Allowed values:
0: Disabled: End of regular conversion interrupt disabled
1: Enabled: End of regular conversion interrupt enabled

EOSIE

Bit 3: EOSIE.

Allowed values:
0: Disabled: End of regular sequence interrupt disabled
1: Enabled: End of regular sequence interrupt enabled

OVRIE

Bit 4: OVRIE.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

JEOCIE

Bit 5: JEOCIE.

Allowed values:
0: Disabled: End of injected conversion interrupt disabled
1: Enabled: End of injected conversion interrupt enabled

JEOSIE

Bit 6: JEOSIE.

Allowed values:
0: Disabled: End of injected sequence interrupt disabled
1: Enabled: End of injected sequence interrupt enabled

AWD1IE

Bit 7: AWD1IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: AWD2IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: AWD3IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

JQOVFIE

Bit 10: JQOVFIE.

Allowed values:
0: Disabled: Injected context queue overflow interrupt disabled
1: Enabled: Injected context queue overflow interrupt enabled

CR

control register

Offset: 0x8, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADCAL
rw 		ADCALDIF
rw 		ADVREGEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JADSTP
rw 		ADSTP
rw 		JADSTART
rw 		ADSTART
rw 		ADDIS
rw 		ADEN
rw
Toggle Fields.

ADEN

Bit 0: ADEN.

Allowed values:
1: Enable: Enable ADC

ADDIS

Bit 1: ADDIS.

Allowed values:
0: Disable: Disable ADC conversion and go to power down mode

ADSTART

Bit 2: ADSTART.

Allowed values:
1: Start: Starts conversion of channel

JADSTART

Bit 3: JADSTART.

Allowed values:
1: Start: Starts conversion of channel

ADSTP

Bit 4: ADSTP.

Allowed values:
1: Stop: Stop conversion of channel

JADSTP

Bit 5: JADSTP.

Allowed values:
1: Stop: Stop conversion of channel

ADVREGEN

Bits 28-29: ADVREGEN.

Allowed values:
0: Intermediate: Intermediate state required when moving the ADC voltage regulator between states
1: Enabled: ADC voltage regulator enabled
2: Disabled: ADC voltage regulator disabled

ADCALDIF

Bit 30: ADCALDIF.

Allowed values:
0: SingleEnded: Calibration for single-ended mode
1: Differential: Calibration for differential mode

ADCAL

Bit 31: ADCAL.

Allowed values:
0: Complete: Calibration complete
1: Calibration: Start the calibration of the ADC

CFGR

configuration register

Offset: 0xC, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD1CH
rw 		JAUTO
rw 		JAWD1EN
rw 		AWD1EN
rw 		AWD1SGL
rw 		JQM
rw 		JDISCEN
rw 		DISCNUM
rw 		DISCEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AUTDLY
rw 		CONT
rw 		OVRMOD
rw 		EXTEN
rw 		EXTSEL
rw 		ALIGN
rw 		RES
rw 		DMACFG
rw 		DMAEN
rw
Toggle Fields.

DMAEN

Bit 0: DMAEN.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: DMACFG.

Allowed values:
0: OneShot: DMA One Shot Mode selected
1: Circular: DMA circular mode selected

RES

Bits 3-4: RES.

Allowed values:
0: Bits12: 12-bit
1: Bits10: 10-bit
2: Bits8: 8-bit
3: Bits6: 6-bit

ALIGN

Bit 5: ALIGN.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-9: EXTSEL.

Allowed values:
7: HRTIM_ADCTRG1: HRTIM_ADCTRG1 event
8: HRTIM_ADCTRG3: HRTIM_ADCTRG3 event
0: TIM1_CC1: Timer 1 CC1 event
1: TIM1_CC2: Timer 1 CC2 event
2: TIM1_CC3: Timer 1 CC3 event
3: TIM2_CC2: Timer 2 CC2 event
4: TIM3_TRGO: Timer 3 TRGO event
6: EXTI11: EXTI line 11
9: TIM1_TRGO: Timer 1 TRGO event
10: TIM1_TRGO2: Timer 1 TRGO2 event
11: TIM2_TRGO: Timer 2 TRGO event
13: TIM6_TRGO: Timer 6 TRGO event
14: TIM15_TRGO: Timer 15 TRGO event
15: TIM3_CC4: Timer 3 CC4 event

EXTEN

Bits 10-11: EXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: OVRMOD.

Allowed values:
0: Preserve: Preserve DR register when an overrun is detected
1: Overwrite: Overwrite DR register when an overrun is detected

CONT

Bit 13: CONT.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

AUTDLY

Bit 14: AUTDLY.

Allowed values:
0: Off: Auto delayed conversion mode off
1: On: Auto delayed conversion mode on

DISCEN

Bit 16: DISCEN.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

DISCNUM

Bits 17-19: DISCNUM.

Allowed values: 0-7

JDISCEN

Bit 20: JDISCEN.

Allowed values:
0: Disabled: Discontinuous mode on injected channels disabled
1: Enabled: Discontinuous mode on injected channels enabled

JQM

Bit 21: JQM.

Allowed values:
0: Mode0: JSQR Mode 0: Queue maintains the last written configuration into JSQR
1: Mode1: JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence

AWD1SGL

Bit 22: AWD1SGL.

Allowed values:
0: All: Analog watchdog 1 enabled on all channels
1: Single: Analog watchdog 1 enabled on single channel selected in AWD1CH

AWD1EN

Bit 23: AWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on regular channels
1: Enabled: Analog watchdog 1 enabled on regular channels

JAWD1EN

Bit 24: JAWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on injected channels
1: Enabled: Analog watchdog 1 enabled on injected channels

JAUTO

Bit 25: JAUTO.

Allowed values:
0: Disabled: Automatic injected group conversion disabled
1: Enabled: Automatic injected group conversion enabled

AWD1CH

Bits 26-30: AWDCH1CH.

Allowed values: 0-19

SMPR1

sample time register 1

Offset: 0x14, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMP9
rw 		SMP8
rw 		SMP7
rw 		SMP6
rw 		SMP5
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SMP5
rw 		SMP4
rw 		SMP3
rw 		SMP2
rw 		SMP1
rw
Toggle Fields.

SMP1

Bits 3-5: SMP1.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP2

Bits 6-8: SMP2.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP3

Bits 9-11: SMP3.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP4

Bits 12-14: SMP4.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP5

Bits 15-17: SMP5.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP6

Bits 18-20: SMP6.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP7

Bits 21-23: SMP7.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP8

Bits 24-26: SMP8.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP9

Bits 27-29: SMP9.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMPR2

sample time register 2

Offset: 0x18, reset: 0x00000000, access: read-write

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMP18
rw 		SMP17
rw 		SMP16
rw 		SMP15
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SMP15
rw 		SMP14
rw 		SMP13
rw 		SMP12
rw 		SMP11
rw 		SMP10
rw
Toggle Fields.

SMP10

Bits 0-2: SMP10.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP11

Bits 3-5: SMP11.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP12

Bits 6-8: SMP12.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP13

Bits 9-11: SMP13.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP14

Bits 12-14: SMP14.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP15

Bits 15-17: SMP15.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP16

Bits 18-20: SMP16.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP17

Bits 21-23: SMP17.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP18

Bits 24-26: SMP18.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

TR1

watchdog threshold register 1

Offset: 0x20, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT1
rw
Toggle Fields.

LT1

Bits 0-11: LT1.

Allowed values: 0-4095

HT1

Bits 16-27: HT1.

Allowed values: 0-4095

TR2

watchdog threshold register

Offset: 0x24, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT2
rw
Toggle Fields.

LT2

Bits 0-7: LT2.

Allowed values: 0-4095

HT2

Bits 16-23: HT2.

Allowed values: 0-4095

TR3

watchdog threshold register 3

Offset: 0x28, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
HT3
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LT3
rw
Toggle Fields.

LT3

Bits 0-7: LT3.

Allowed values: 0-4095

HT3

Bits 16-23: HT3.

Allowed values: 0-4095

SQR1

regular sequence register 1

Offset: 0x30, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ4
rw 		SQ3
rw 		SQ2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ2
rw 		SQ1
rw 		L
rw
Toggle Fields.

L

Bits 0-3: L3.

Allowed values: 0-15

SQ1

Bits 6-10: SQ1.

Allowed values: 0-19

SQ2

Bits 12-16: SQ2.

Allowed values: 0-19

SQ3

Bits 18-22: SQ3.

Allowed values: 0-19

SQ4

Bits 24-28: SQ4.

Allowed values: 0-19

SQR2

regular sequence register 2

Offset: 0x34, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ9
rw 		SQ8
rw 		SQ7
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ7
rw 		SQ6
rw 		SQ5
rw
Toggle Fields.

SQ5

Bits 0-4: SQ5.

Allowed values: 0-19

SQ6

Bits 6-10: SQ6.

Allowed values: 0-19

SQ7

Bits 12-16: SQ7.

Allowed values: 0-19

SQ8

Bits 18-22: SQ8.

Allowed values: 0-19

SQ9

Bits 24-28: SQ9.

Allowed values: 0-19

SQR3

regular sequence register 3

Offset: 0x38, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SQ14
rw 		SQ13
rw 		SQ12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ12
rw 		SQ11
rw 		SQ10
rw
Toggle Fields.

SQ10

Bits 0-4: SQ10.

Allowed values: 0-19

SQ11

Bits 6-10: SQ11.

Allowed values: 0-19

SQ12

Bits 12-16: SQ12.

Allowed values: 0-19

SQ13

Bits 18-22: SQ13.

Allowed values: 0-19

SQ14

Bits 24-28: SQ14.

Allowed values: 0-19

SQR4

regular sequence register 4

Offset: 0x3C, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SQ16
rw 		SQ15
rw
Toggle Fields.

SQ15

Bits 0-4: SQ15.

Allowed values: 0-19

SQ16

Bits 6-10: SQ16.

Allowed values: 0-19

DR

regular Data Register

Offset: 0x40, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA
r
Toggle Fields.

RDATA

Bits 0-15: regularDATA.

JSQR

injected sequence register

Offset: 0x4C, reset: 0x00000000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JSQ4
rw 		JSQ3
rw 		JSQ2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JSQ2
rw 		JSQ1
rw 		JEXTEN
rw 		JEXTSEL
rw 		JL
rw
Toggle Fields.

JL

Bits 0-1: JL.

Allowed values: 0-3

JEXTSEL

Bits 2-5: JEXTSEL.

Allowed values:
9: HRTIM_ADCTRG2: HRTIM_ADCTRG2 event
10: HRTIM_ADCTRG4: HRTIM_ADCTRG4 event

JEXTEN

Bits 6-7: JEXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

JSQ1

Bits 8-12: JSQ1.

Allowed values: 0-19

JSQ2

Bits 14-18: JSQ2.

Allowed values: 0-19

JSQ3

Bits 20-24: JSQ3.

Allowed values: 0-19

JSQ4

Bits 26-30: JSQ4.

Allowed values: 0-19

OFR1

offset register 1

Offset: 0x60, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET1_EN
rw 		OFFSET1_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET1
rw
Toggle Fields.

OFFSET1

Bits 0-11: OFFSET1.

Allowed values: 0-4095

OFFSET1_CH

Bits 26-30: OFFSET1_CH.

Allowed values: 0-31

OFFSET1_EN

Bit 31: OFFSET1_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR2

offset register 2

Offset: 0x64, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET2_EN
rw 		OFFSET2_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET2
rw
Toggle Fields.

OFFSET2

Bits 0-11: OFFSET2.

Allowed values: 0-4095

OFFSET2_CH

Bits 26-30: OFFSET2_CH.

Allowed values: 0-31

OFFSET2_EN

Bit 31: OFFSET2_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR3

offset register 3

Offset: 0x68, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET3_EN
rw 		OFFSET3_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET3
rw
Toggle Fields.

OFFSET3

Bits 0-11: OFFSET3.

Allowed values: 0-4095

OFFSET3_CH

Bits 26-30: OFFSET3_CH.

Allowed values: 0-31

OFFSET3_EN

Bit 31: OFFSET3_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR4

offset register 4

Offset: 0x6C, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OFFSET4_EN
rw 		OFFSET4_CH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET4
rw
Toggle Fields.

OFFSET4

Bits 0-11: OFFSET4.

Allowed values: 0-4095

OFFSET4_CH

Bits 26-30: OFFSET4_CH.

Allowed values: 0-31

OFFSET4_EN

Bit 31: OFFSET4_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

JDR1

injected data register 1

Offset: 0x80, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: JDATA1.

JDR2

injected data register 2

Offset: 0x84, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA2
r
Toggle Fields.

JDATA2

Bits 0-15: JDATA2.

JDR3

injected data register 3

Offset: 0x88, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA3
r
Toggle Fields.

JDATA3

Bits 0-15: JDATA3.

JDR4

injected data register 4

Offset: 0x8C, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA4
r
Toggle Fields.

JDATA4

Bits 0-15: JDATA4.

AWD2CR

Analog Watchdog 2 Configuration Register

Offset: 0xA0, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD2CH17
rw 		AWD2CH16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AWD2CH15
rw 		AWD2CH14
rw 		AWD2CH13
rw 		AWD2CH12
rw 		AWD2CH11
rw 		AWD2CH10
rw 		AWD2CH9
rw 		AWD2CH8
rw 		AWD2CH7
rw 		AWD2CH6
rw 		AWD2CH5
rw 		AWD2CH4
rw 		AWD2CH3
rw 		AWD2CH2
rw 		AWD2CH1
rw 		AWD2CH0
rw
Toggle Fields.

AWD2CH0

Bit 0: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH1

Bit 1: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH2

Bit 2: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH3

Bit 3: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH4

Bit 4: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH5

Bit 5: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH6

Bit 6: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH7

Bit 7: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH8

Bit 8: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH9

Bit 9: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH10

Bit 10: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH11

Bit 11: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH12

Bit 12: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH13

Bit 13: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH14

Bit 14: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH15

Bit 15: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH16

Bit 16: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH17

Bit 17: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CR

Analog Watchdog 3 Configuration Register

Offset: 0xA4, reset: 0x00000000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AWD3CH17
rw 		AWD3CH16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AWD3CH15
rw 		AWD3CH14
rw 		AWD3CH13
rw 		AWD3CH12
rw 		AWD3CH11
rw 		AWD3CH10
rw 		AWD3CH9
rw 		AWD3CH8
rw 		AWD3CH7
rw 		AWD3CH6
rw 		AWD3CH5
rw 		AWD3CH4
rw 		AWD3CH3
rw 		AWD3CH2
rw 		AWD3CH1
rw 		AWD3CH0
rw
Toggle Fields.

AWD3CH0

Bit 0: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH1

Bit 1: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH2

Bit 2: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH3

Bit 3: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH4

Bit 4: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH5

Bit 5: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH6

Bit 6: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH7

Bit 7: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH8

Bit 8: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH9

Bit 9: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH10

Bit 10: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH11

Bit 11: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH12

Bit 12: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH13

Bit 13: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH14

Bit 14: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH15

Bit 15: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH16

Bit 16: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH17

Bit 17: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

DIFSEL

Differential Mode Selection Register 2

Offset: 0xB0, reset: 0x00000000, access: Unspecified

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DIFSEL_117
N/A 		DIFSEL_116
N/A
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DIFSEL_115
N/A 		DIFSEL_114
N/A 		DIFSEL_113
N/A 		DIFSEL_112
N/A 		DIFSEL_111
N/A 		DIFSEL_110
N/A 		DIFSEL_19
N/A 		DIFSEL_18
N/A 		DIFSEL_17
N/A 		DIFSEL_16
N/A 		DIFSEL_15
N/A 		DIFSEL_14
N/A 		DIFSEL_13
N/A 		DIFSEL_12
N/A 		DIFSEL_11
N/A 		DIFSEL_10
N/A
Toggle Fields.

DIFSEL_10

Bit 0: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_11

Bit 1: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_12

Bit 2: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_13

Bit 3: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_14

Bit 4: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_15

Bit 5: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_16

Bit 6: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_17

Bit 7: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_18

Bit 8: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_19

Bit 9: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_110

Bit 10: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_111

Bit 11: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_112

Bit 12: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_113

Bit 13: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_114

Bit 14: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_115

Bit 15: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_116

Bit 16: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_117

Bit 17: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

CALFACT

Calibration Factors

Offset: 0xB4, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CALFACT_D
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CALFACT_S
rw
Toggle Fields.

CALFACT_S

Bits 0-6: CALFACT_S.

Allowed values: 0-127

CALFACT_D

Bits 16-22: CALFACT_D.

Allowed values: 0-127

CAN

0x40006400: Controller area network

57/280 fields covered. Toggle Registers.

FR1

Filter bank 0 register 1

Offset: 0x0, reset: 0x00000000, access: read-write

0/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FB31
rw 		FB30
rw 		FB29
rw 		FB28
rw 		FB27
rw 		FB26
rw 		FB25
rw 		FB24
rw 		FB23
rw 		FB22
rw 		FB21
rw 		FB20
rw 		FB19
rw 		FB18
rw 		FB17
rw 		FB16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FB15
rw 		FB14
rw 		FB13
rw 		FB12
rw 		FB11
rw 		FB10
rw 		FB9
rw 		FB8
rw 		FB7
rw 		FB6
rw 		FB5
rw 		FB4
rw 		FB3
rw 		FB2
rw 		FB1
rw 		FB0
rw
Toggle Fields.

FB0

Bit 0: Filter bits.

FB1

Bit 1: Filter bits.

FB2

Bit 2: Filter bits.

FB3

Bit 3: Filter bits.

FB4

Bit 4: Filter bits.

FB5

Bit 5: Filter bits.

FB6

Bit 6: Filter bits.

FB7

Bit 7: Filter bits.

FB8

Bit 8: Filter bits.

FB9

Bit 9: Filter bits.

FB10

Bit 10: Filter bits.

FB11

Bit 11: Filter bits.

FB12

Bit 12: Filter bits.

FB13

Bit 13: Filter bits.

FB14

Bit 14: Filter bits.

FB15

Bit 15: Filter bits.

FB16

Bit 16: Filter bits.

FB17

Bit 17: Filter bits.

FB18

Bit 18: Filter bits.

FB19

Bit 19: Filter bits.

FB20

Bit 20: Filter bits.

FB21

Bit 21: Filter bits.

FB22

Bit 22: Filter bits.

FB23

Bit 23: Filter bits.

FB24

Bit 24: Filter bits.

FB25

Bit 25: Filter bits.

FB26

Bit 26: Filter bits.

FB27

Bit 27: Filter bits.

FB28

Bit 28: Filter bits.

FB29

Bit 29: Filter bits.

FB30

Bit 30: Filter bits.

FB31

Bit 31: Filter bits.

FR2

Filter bank 0 register 2

Offset: 0x4, reset: 0x00000000, access: read-write

0/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FB31
rw 		FB30
rw 		FB29
rw 		FB28
rw 		FB27
rw 		FB26
rw 		FB25
rw 		FB24
rw 		FB23
rw 		FB22
rw 		FB21
rw 		FB20
rw 		FB19
rw 		FB18
rw 		FB17
rw 		FB16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FB15
rw 		FB14
rw 		FB13
rw 		FB12
rw 		FB11
rw 		FB10
rw 		FB9
rw 		FB8
rw 		FB7
rw 		FB6
rw 		FB5
rw 		FB4
rw 		FB3
rw 		FB2
rw 		FB1
rw 		FB0
rw
Toggle Fields.

FB0

Bit 0: Filter bits.

FB1

Bit 1: Filter bits.

FB2

Bit 2: Filter bits.

FB3

Bit 3: Filter bits.

FB4

Bit 4: Filter bits.

FB5

Bit 5: Filter bits.

FB6

Bit 6: Filter bits.

FB7

Bit 7: Filter bits.

FB8

Bit 8: Filter bits.

FB9

Bit 9: Filter bits.

FB10

Bit 10: Filter bits.

FB11

Bit 11: Filter bits.

FB12

Bit 12: Filter bits.

FB13

Bit 13: Filter bits.

FB14

Bit 14: Filter bits.

FB15

Bit 15: Filter bits.

FB16

Bit 16: Filter bits.

FB17

Bit 17: Filter bits.

FB18

Bit 18: Filter bits.

FB19

Bit 19: Filter bits.

FB20

Bit 20: Filter bits.

FB21

Bit 21: Filter bits.

FB22

Bit 22: Filter bits.

FB23

Bit 23: Filter bits.

FB24

Bit 24: Filter bits.

FB25

Bit 25: Filter bits.

FB26

Bit 26: Filter bits.

FB27

Bit 27: Filter bits.

FB28

Bit 28: Filter bits.

FB29

Bit 29: Filter bits.

FB30

Bit 30: Filter bits.

FB31

Bit 31: Filter bits.

RDLR

receive FIFO mailbox data low register

Offset: 0x8, reset: 0x00000000, access: read-only

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DATA3
r 		DATA2
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATA1
r 		DATA0
r
Toggle Fields.

DATA0

Bits 0-7: DATA0.

DATA1

Bits 8-15: DATA1.

DATA2

Bits 16-23: DATA2.

DATA3

Bits 24-31: DATA3.

RDHR

receive FIFO mailbox data high register

Offset: 0xC, reset: 0x00000000, access: read-only

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DATA7
r 		DATA6
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATA5
r 		DATA4
r
Toggle Fields.

DATA4

Bits 0-7: DATA4.

DATA5

Bits 8-15: DATA5.

DATA6

Bits 16-23: DATA6.

DATA7

Bits 24-31: DATA7.

IER

interrupt enable register

Offset: 0x14, reset: 0x00000000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SLKIE
rw 		WKUIE
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ERRIE
rw 		LECIE
rw 		BOFIE
rw 		EPVIE
rw 		EWGIE
rw 		FOVIE1
rw 		FFIE1
rw 		FMPIE1
rw 		FOVIE0
rw 		FFIE0
rw 		FMPIE0
rw 		TMEIE
rw
Toggle Fields.

TMEIE

Bit 0: TMEIE.

Allowed values:
0: Disabled: No interrupt when RQCPx bit is set
1: Enabled: Interrupt generated when RQCPx bit is set

FMPIE0

Bit 1: FMPIE0.

Allowed values:
0: Disabled: No interrupt generated when state of FMP[1:0] bits are not 00
1: Enabled: Interrupt generated when state of FMP[1:0] bits are not 00b

FFIE0

Bit 2: FFIE0.

Allowed values:
0: Disabled: No interrupt when FULL bit is set
1: Enabled: Interrupt generated when FULL bit is set

FOVIE0

Bit 3: FOVIE0.

Allowed values:
0: Disabled: No interrupt when FOVR bit is set
1: Enabled: Interrupt generated when FOVR bit is set

FMPIE1

Bit 4: FMPIE1.

Allowed values:
0: Disabled: No interrupt generated when state of FMP[1:0] bits are not 00b
1: Enabled: Interrupt generated when state of FMP[1:0] bits are not 00b

FFIE1

Bit 5: FFIE1.

Allowed values:
0: Disabled: No interrupt when FULL bit is set
1: Enabled: Interrupt generated when FULL bit is set

FOVIE1

Bit 6: FOVIE1.

Allowed values:
0: Disabled: No interrupt when FOVR is set
1: Enabled: Interrupt generation when FOVR is set

EWGIE

Bit 8: EWGIE.

Allowed values:
0: Disabled: ERRI bit will not be set when EWGF is set
1: Enabled: ERRI bit will be set when EWGF is set

EPVIE

Bit 9: EPVIE.

Allowed values:
0: Disabled: ERRI bit will not be set when EPVF is set
1: Enabled: ERRI bit will be set when EPVF is set

BOFIE

Bit 10: BOFIE.

Allowed values:
0: Disabled: ERRI bit will not be set when BOFF is set
1: Enabled: ERRI bit will be set when BOFF is set

LECIE

Bit 11: LECIE.

Allowed values:
0: Disabled: ERRI bit will not be set when the error code in LEC[2:0] is set by hardware on error detection
1: Enabled: ERRI bit will be set when the error code in LEC[2:0] is set by hardware on error detection

ERRIE

Bit 15: ERRIE.

Allowed values:
0: Disabled: No interrupt will be generated when an error condition is pending in the CAN_ESR
1: Enabled: An interrupt will be generation when an error condition is pending in the CAN_ESR

WKUIE

Bit 16: WKUIE.

Allowed values:
0: Disabled: No interrupt when WKUI is set
1: Enabled: Interrupt generated when WKUI bit is set

SLKIE

Bit 17: SLKIE.

Allowed values:
0: Disabled: No interrupt when SLAKI bit is set
1: Enabled: Interrupt generated when SLAKI bit is set

ESR

error status register

Offset: 0x18, reset: 0x00000000, access: Unspecified

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
REC
r 		TEC
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LEC
rw 		BOFF
r 		EPVF
r 		EWGF
r
Toggle Fields.

EWGF

Bit 0: EWGF.

EPVF

Bit 1: EPVF.

BOFF

Bit 2: BOFF.

LEC

Bits 4-6: LEC.

Allowed values:
0: NoError: No Error
1: Stuff: Stuff Error
2: Form: Form Error
3: Ack: Acknowledgment Error
4: BitRecessive: Bit recessive Error
5: BitDominant: Bit dominant Error
6: Crc: CRC Error
7: Custom: Set by software

TEC

Bits 16-23: TEC.

REC

Bits 24-31: REC.

BTR

bit timing register

Offset: 0x1C, reset: 0x01230000, access: read-write

2/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SILM
rw 		LBKM
rw 		SJW
rw 		TS2
rw 		TS1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BRP
rw
Toggle Fields.

BRP

Bits 0-9: BRP.

TS1

Bits 16-19: TS1.

TS2

Bits 20-22: TS2.

SJW

Bits 24-25: SJW.

LBKM

Bit 30: LBKM.

Allowed values:
0: Disabled: Loop Back Mode disabled
1: Enabled: Loop Back Mode enabled

SILM

Bit 31: SILM.

Allowed values:
0: Normal: Normal operation
1: Silent: Silent Mode

FMR

filter master register

Offset: 0x200, reset: 0x2A1C0E01, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CAN2SB
rw 		FINIT
rw
Toggle Fields.

FINIT

Bit 0: FINIT.

CAN2SB

Bits 8-13: CAN2SB.

FM1R

filter mode register

Offset: 0x204, reset: 0x00000000, access: read-write

0/28 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FBM27
rw 		FBM26
rw 		FBM25
rw 		FBM24
rw 		FBM23
rw 		FBM22
rw 		FBM21
rw 		FBM20
rw 		FBM19
rw 		FBM18
rw 		FBM17
rw 		FBM16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FBM15
rw 		FBM14
rw 		FBM13
rw 		FBM12
rw 		FBM11
rw 		FBM10
rw 		FBM9
rw 		FBM8
rw 		FBM7
rw 		FBM6
rw 		FBM5
rw 		FBM4
rw 		FBM3
rw 		FBM2
rw 		FBM1
rw 		FBM0
rw
Toggle Fields.

FBM0

Bit 0: Filter mode.

FBM1

Bit 1: Filter mode.

FBM2

Bit 2: Filter mode.

FBM3

Bit 3: Filter mode.

FBM4

Bit 4: Filter mode.

FBM5

Bit 5: Filter mode.

FBM6

Bit 6: Filter mode.

FBM7

Bit 7: Filter mode.

FBM8

Bit 8: Filter mode.

FBM9

Bit 9: Filter mode.

FBM10

Bit 10: Filter mode.

FBM11

Bit 11: Filter mode.

FBM12

Bit 12: Filter mode.

FBM13

Bit 13: Filter mode.

FBM14

Bit 14: Filter mode.

FBM15

Bit 15: Filter mode.

FBM16

Bit 16: Filter mode.

FBM17

Bit 17: Filter mode.

FBM18

Bit 18: Filter mode.

FBM19

Bit 19: Filter mode.

FBM20

Bit 20: Filter mode.

FBM21

Bit 21: Filter mode.

FBM22

Bit 22: Filter mode.

FBM23

Bit 23: Filter mode.

FBM24

Bit 24: Filter mode.

FBM25

Bit 25: Filter mode.

FBM26

Bit 26: Filter mode.

FBM27

Bit 27: Filter mode.

FS1R

filter scale register

Offset: 0x20C, reset: 0x00000000, access: read-write

0/28 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FSC27
rw 		FSC26
rw 		FSC25
rw 		FSC24
rw 		FSC23
rw 		FSC22
rw 		FSC21
rw 		FSC20
rw 		FSC19
rw 		FSC18
rw 		FSC17
rw 		FSC16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FSC15
rw 		FSC14
rw 		FSC13
rw 		FSC12
rw 		FSC11
rw 		FSC10
rw 		FSC9
rw 		FSC8
rw 		FSC7
rw 		FSC6
rw 		FSC5
rw 		FSC4
rw 		FSC3
rw 		FSC2
rw 		FSC1
rw 		FSC0
rw
Toggle Fields.

FSC0

Bit 0: Filter scale configuration.

FSC1

Bit 1: Filter scale configuration.

FSC2

Bit 2: Filter scale configuration.

FSC3

Bit 3: Filter scale configuration.

FSC4

Bit 4: Filter scale configuration.

FSC5

Bit 5: Filter scale configuration.

FSC6

Bit 6: Filter scale configuration.

FSC7

Bit 7: Filter scale configuration.

FSC8

Bit 8: Filter scale configuration.

FSC9

Bit 9: Filter scale configuration.

FSC10

Bit 10: Filter scale configuration.

FSC11

Bit 11: Filter scale configuration.

FSC12

Bit 12: Filter scale configuration.

FSC13

Bit 13: Filter scale configuration.

FSC14

Bit 14: Filter scale configuration.

FSC15

Bit 15: Filter scale configuration.

FSC16

Bit 16: Filter scale configuration.

FSC17

Bit 17: Filter scale configuration.

FSC18

Bit 18: Filter scale configuration.

FSC19

Bit 19: Filter scale configuration.

FSC20

Bit 20: Filter scale configuration.

FSC21

Bit 21: Filter scale configuration.

FSC22

Bit 22: Filter scale configuration.

FSC23

Bit 23: Filter scale configuration.

FSC24

Bit 24: Filter scale configuration.

FSC25

Bit 25: Filter scale configuration.

FSC26

Bit 26: Filter scale configuration.

FSC27

Bit 27: Filter scale configuration.

FFA1R

filter FIFO assignment register

Offset: 0x214, reset: 0x00000000, access: read-write

0/28 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FFA27
rw 		FFA26
rw 		FFA25
rw 		FFA24
rw 		FFA23
rw 		FFA22
rw 		FFA21
rw 		FFA20
rw 		FFA19
rw 		FFA18
rw 		FFA17
rw 		FFA16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FFA15
rw 		FFA14
rw 		FFA13
rw 		FFA12
rw 		FFA11
rw 		FFA10
rw 		FFA9
rw 		FFA8
rw 		FFA7
rw 		FFA6
rw 		FFA5
rw 		FFA4
rw 		FFA3
rw 		FFA2
rw 		FFA1
rw 		FFA0
rw
Toggle Fields.

FFA0

Bit 0: Filter FIFO assignment for filter 0.

FFA1

Bit 1: Filter FIFO assignment for filter 1.

FFA2

Bit 2: Filter FIFO assignment for filter 2.

FFA3

Bit 3: Filter FIFO assignment for filter 3.

FFA4

Bit 4: Filter FIFO assignment for filter 4.

FFA5

Bit 5: Filter FIFO assignment for filter 5.

FFA6

Bit 6: Filter FIFO assignment for filter 6.

FFA7

Bit 7: Filter FIFO assignment for filter 7.

FFA8

Bit 8: Filter FIFO assignment for filter 8.

FFA9

Bit 9: Filter FIFO assignment for filter 9.

FFA10

Bit 10: Filter FIFO assignment for filter 10.

FFA11

Bit 11: Filter FIFO assignment for filter 11.

FFA12

Bit 12: Filter FIFO assignment for filter 12.

FFA13

Bit 13: Filter FIFO assignment for filter 13.

FFA14

Bit 14: Filter FIFO assignment for filter 14.

FFA15

Bit 15: Filter FIFO assignment for filter 15.

FFA16

Bit 16: Filter FIFO assignment for filter 16.

FFA17

Bit 17: Filter FIFO assignment for filter 17.

FFA18

Bit 18: Filter FIFO assignment for filter 18.

FFA19

Bit 19: Filter FIFO assignment for filter 19.

FFA20

Bit 20: Filter FIFO assignment for filter 20.

FFA21

Bit 21: Filter FIFO assignment for filter 21.

FFA22

Bit 22: Filter FIFO assignment for filter 22.

FFA23

Bit 23: Filter FIFO assignment for filter 23.

FFA24

Bit 24: Filter FIFO assignment for filter 24.

FFA25

Bit 25: Filter FIFO assignment for filter 25.

FFA26

Bit 26: Filter FIFO assignment for filter 26.

FFA27

Bit 27: Filter FIFO assignment for filter 27.

FA1R

CAN filter activation register

Offset: 0x21C, reset: 0x00000000, access: read-write

0/28 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FACT27
rw 		FACT26
rw 		FACT25
rw 		FACT24
rw 		FACT23
rw 		FACT22
rw 		FACT21
rw 		FACT20
rw 		FACT19
rw 		FACT18
rw 		FACT17
rw 		FACT16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FACT15
rw 		FACT14
rw 		FACT13
rw 		FACT12
rw 		FACT11
rw 		FACT10
rw 		FACT9
rw 		FACT8
rw 		FACT7
rw 		FACT6
rw 		FACT5
rw 		FACT4
rw 		FACT3
rw 		FACT2
rw 		FACT1
rw 		FACT0
rw
Toggle Fields.

FACT0

Bit 0: Filter active.

FACT1

Bit 1: Filter active.

FACT2

Bit 2: Filter active.

FACT3

Bit 3: Filter active.

FACT4

Bit 4: Filter active.

FACT5

Bit 5: Filter active.

FACT6

Bit 6: Filter active.

FACT7

Bit 7: Filter active.

FACT8

Bit 8: Filter active.

FACT9

Bit 9: Filter active.

FACT10

Bit 10: Filter active.

FACT11

Bit 11: Filter active.

FACT12

Bit 12: Filter active.

FACT13

Bit 13: Filter active.

FACT14

Bit 14: Filter active.

FACT15

Bit 15: Filter active.

FACT16

Bit 16: Filter active.

FACT17

Bit 17: Filter active.

FACT18

Bit 18: Filter active.

FACT19

Bit 19: Filter active.

FACT20

Bit 20: Filter active.

FACT21

Bit 21: Filter active.

FACT22

Bit 22: Filter active.

FACT23

Bit 23: Filter active.

FACT24

Bit 24: Filter active.

FACT25

Bit 25: Filter active.

FACT26

Bit 26: Filter active.

FACT27

Bit 27: Filter active.

COMP

1073807360: General purpose comparators

25/76 fields covered. Toggle Registers.

COMP1_CSR

control and status register

Offset: 0x28, reset: 0, access: Unspecified

1/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMP1LOCK
rw 		COMP1OUT
r 		COMP1_BLANKING
rw 		COMP1HYST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
COMP1POL
rw 		COMP1OUTSEL
rw 		COMP1INMSEL
rw 		COMP1MODE
rw 		COMP1_INP_DAC
rw 		COMP1EN
rw
Toggle Fields.

COMP1EN

Bit 0: Comparator 1 enable.

COMP1_INP_DAC

Bit 1: Comparator 1 non inverting input connection to DAC output.

COMP1MODE

Bits 2-3: Comparator 1 mode.

COMP1INMSEL

Bits 4-6: Comparator 1 inverting input selection.

COMP1OUTSEL

Bits 10-13: Comparator 1 output selection.

COMP1POL

Bit 15: Comparator 1 output polarity.

COMP1HYST

Bits 16-17: Comparator 1 hysteresis.

COMP1_BLANKING

Bits 18-20: Comparator 1 blanking source.

COMP1OUT

Bit 30: Comparator 1 output.

COMP1LOCK

Bit 31: Comparator 1 lock.

COMP2_CSR

control and status register

Offset: 0x32, reset: 0, access: Unspecified

7/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMP2LOCK
rw 		COMP2OUT
r 		COMP2INMSEL3
rw 		COMP2_BLANKING
rw 		COMP2HYST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
COMP2POL
rw 		COMP2OUTSEL
rw 		COMP2WINMODE
rw 		COMP2INPSEL
rw 		COMP2INMSEL
rw 		COMP2MODE
rw 		COMP2EN
rw
Toggle Fields.

COMP2EN

Bit 0: Comparator 2 enable.

Allowed values:
0: Disabled: Comparator disabled
1: Enabled: Comparator enabled

COMP2MODE

Bits 2-3: Comparator 2 mode.

COMP2INMSEL

Bits 4-6: Comparator 2 inverting input selection.

Allowed values:
0: OneQuarterVRef: 1/4 of VRefint
1: OneHalfVRef: 1/2 of VRefint
2: ThreeQuarterVRef: 3/4 of VRefint
3: VRef: VRefint
4: PA4_DAC1_CH1: PA4 or DAC1_CH1 output if enabled
5: DAC1_CH2: DAC1_CH2
6: PA2: PA2

COMP2INPSEL

Bit 7: Comparator 2 non inverted input.

COMP2WINMODE

Bit 9: Comparator 2 window mode.

COMP2OUTSEL

Bits 10-13: Comparator 2 output selection.

Allowed values:
0: NoSelection: No selection
1: Timer1BreakInput: Timer 1 break input
2: Timer1BreakInput2: Timer 1 break input 2
6: Timer1OCRefClearInput: Timer 1 OCREF_CLR input
7: Timer1InputCapture1: Timer 1 input capture 1
8: Timer2InputCapture4: Timer 2 input capture 4
9: Timer2OCRefClearInput: Timer 2 OCREF_CLR input
10: Timer3InputCapture1: Timer 3 input capture 1
11: Timer3OCRefClearInput: Timer 3 OCREF_CLR input

COMP2POL

Bit 15: Comparator 2 output polarity.

Allowed values:
0: NotInverted: Output is not inverted
1: Inverted: Output is inverted

COMP2HYST

Bits 16-17: Comparator 2 hysteresis.

COMP2_BLANKING

Bits 18-20: Comparator 2 blanking source.

Allowed values:
0: NoBlanking: No blanking
1: TIM1OC5: TIM1 OC5 selected as blanking source
2: TIM2OC3: TIM2 OC3 selected as blanking source
3: TIM3OC3: TIM3 OC3 selected as blanking source

COMP2INMSEL3

Bit 22: Comparator 2 inverting input selection.

COMP2OUT

Bit 30: Comparator 2 output.

Allowed values:
0: Low: Non-inverting input below inverting input
1: High: Non-inverting input above inverting input

COMP2LOCK

Bit 31: Comparator 2 lock.

Allowed values:
0: Unlocked: Comparator CSR bits are read-write
1: Locked: Comparator CSR bits are read-only

COMP3_CSR

control and status register

Offset: 0x36, reset: 0, access: Unspecified

1/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMP3LOCK
rw 		COMP3OUT
r 		COMP3_BLANKING
rw 		COMP3HYST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
COMP3POL
rw 		COMP3OUTSEL
rw 		COMP3INPSEL
rw 		COMP3INMSEL
rw 		COMP3MODE
rw 		COMP3EN
rw
Toggle Fields.

COMP3EN

Bit 0: Comparator 3 enable.

COMP3MODE

Bits 2-3: Comparator 3 mode.

COMP3INMSEL

Bits 4-6: Comparator 3 inverting input selection.

COMP3INPSEL

Bit 7: Comparator 3 non inverted input.

COMP3OUTSEL

Bits 10-13: Comparator 3 output selection.

COMP3POL

Bit 15: Comparator 3 output polarity.

COMP3HYST

Bits 16-17: Comparator 3 hysteresis.

COMP3_BLANKING

Bits 18-20: Comparator 3 blanking source.

COMP3OUT

Bit 30: Comparator 3 output.

COMP3LOCK

Bit 31: Comparator 3 lock.

COMP4_CSR

control and status register

Offset: 0x40, reset: 0, access: Unspecified

7/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMP4LOCK
rw 		COMP4OUT
r 		COMP4INMSEL3
rw 		COMP4_BLANKING
rw 		COMP4HYST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
COMP4POL
rw 		COMP4OUTSEL
rw 		COMP4WINMODE
rw 		COMP4INPSEL
rw 		COMP4INMSEL
rw 		COMP4MODE
rw 		COMP4EN
rw
Toggle Fields.

COMP4EN

Bit 0: Comparator 4 enable.

Allowed values:
0: Disabled: Comparator disabled
1: Enabled: Comparator enabled

COMP4MODE

Bits 2-3: Comparator 4 mode.

COMP4INMSEL

Bits 4-6: Comparator 4 inverting input selection.

Allowed values:
0: OneQuarterVRef: 1/4 of VRefint
1: OneHalfVRef: 1/2 of VRefint
2: ThreeQuarterVRef: 3/4 of VRefint
3: VRef: VRefint
4: PA4_DAC1_CH1: PA4 or DAC1_CH1 output if enabled
5: DAC1_CH2: DAC1_CH2
7: PB2: PB2

COMP4INPSEL

Bit 7: Comparator 4 non inverted input.

COMP4WINMODE

Bit 9: Comparator 4 window mode.

COMP4OUTSEL

Bits 10-13: Comparator 4 output selection.

Allowed values:
0: NoSelection: No selection
1: Timer1BreakInput: Timer 1 break input
2: Timer1BreakInput2: Timer 1 break input 2
6: Timer3InputCapture3: Timer 3 input capture 3
8: Timer15InputCapture2: Timer 15 input capture 2
10: Timer15OCRefClearInput: Timer 15 OCREF_CLR input
11: Timer3OCRefClearInput: Timer 3 OCREF_CLR input

COMP4POL

Bit 15: Comparator 4 output polarity.

Allowed values:
0: NotInverted: Output is not inverted
1: Inverted: Output is inverted

COMP4HYST

Bits 16-17: Comparator 4 hysteresis.

COMP4_BLANKING

Bits 18-20: Comparator 4 blanking source.

Allowed values:
0: NoBlanking: No blanking
1: TIM3OC4: TIM3 OC4 selected as blanking source
3: TIM15OC1: TIM15 OC1 selected as blanking source

COMP4INMSEL3

Bit 22: Comparator 4 inverting input selection.

COMP4OUT

Bit 30: Comparator 4 output.

Allowed values:
0: Low: Non-inverting input below inverting input
1: High: Non-inverting input above inverting input

COMP4LOCK

Bit 31: Comparator 4 lock.

Allowed values:
0: Unlocked: Comparator CSR bits are read-write
1: Locked: Comparator CSR bits are read-only

COMP5_CSR

control and status register

Offset: 0x44, reset: 0, access: Unspecified

1/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMP5LOCK
rw 		COMP5OUT
r 		COMP5_BLANKING
rw 		COMP5HYST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
COMP5POL
rw 		COMP5OUTSEL
rw 		COMP5INPSEL
rw 		COMP5INMSEL
rw 		COMP5MODE
rw 		COMP5EN
rw
Toggle Fields.

COMP5EN

Bit 0: Comparator 5 enable.

COMP5MODE

Bits 2-3: Comparator 5 mode.

COMP5INMSEL

Bits 4-6: Comparator 5 inverting input selection.

COMP5INPSEL

Bit 7: Comparator 5 non inverted input.

COMP5OUTSEL

Bits 10-13: Comparator 5 output selection.

COMP5POL

Bit 15: Comparator 5 output polarity.

COMP5HYST

Bits 16-17: Comparator 5 hysteresis.

COMP5_BLANKING

Bits 18-20: Comparator 5 blanking source.

COMP5OUT

Bit 30: Comparator 5 output.

COMP5LOCK

Bit 31: Comparator 5 lock.

COMP6_CSR

control and status register

Offset: 0x48, reset: 0, access: Unspecified

7/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMP6LOCK
rw 		COMP6OUT
r 		COMP6INMSEL3
rw 		COMP6_BLANKING
rw 		COMP6HYST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
COMP6POL
rw 		COMP6OUTSEL
rw 		COMP6WINMODE
rw 		COMP6INPSEL
rw 		COMP6INMSEL
rw 		COMP6MODE
rw 		COMP6EN
rw
Toggle Fields.

COMP6EN

Bit 0: Comparator 6 enable.

Allowed values:
0: Disabled: Comparator disabled
1: Enabled: Comparator enabled

COMP6MODE

Bits 2-3: Comparator 6 mode.

COMP6INMSEL

Bits 4-6: Comparator 6 inverting input selection.

Allowed values:
0: OneQuarterVRef: 1/4 of VRefint
1: OneHalfVRef: 1/2 of VRefint
2: ThreeQuarterVRef: 3/4 of VRefint
3: VRef: VRefint
4: PA4_DAC1_CH1: PA4 or DAC1_CH1 output if enabled
5: DAC1_CH2: DAC1_CH2
7: PB15: PB15

COMP6INPSEL

Bit 7: Comparator 6 non inverted input.

COMP6WINMODE

Bit 9: Comparator 6 window mode.

COMP6OUTSEL

Bits 10-13: Comparator 6 output selection.

Allowed values:
0: NoSelection: No selection
1: Timer1BreakInput: Timer 1 break input
2: Timer1BreakInput2: Timer 1 break input 2
6: Timer2InputCapture2: Timer 2 input capture 2
8: Timer2OCRefClearInput: Timer 2 OCREF_CLR input
9: Timer16OCRefClearInput: Timer 16 OCREF_CLR input
10: Timer16InputCapture1: Timer 16 input capture 1

COMP6POL

Bit 15: Comparator 6 output polarity.

Allowed values:
0: NotInverted: Output is not inverted
1: Inverted: Output is inverted

COMP6HYST

Bits 16-17: Comparator 6 hysteresis.

COMP6_BLANKING

Bits 18-20: Comparator 6 blanking source.

Allowed values:
0: NoBlanking: No blanking
3: TIM2OC4: TIM2 OC4 selected as blanking source
4: TIM15OC2: TIM15 OC2 selected as blanking source

COMP6INMSEL3

Bit 22: Comparator 6 inverting input selection.

COMP6OUT

Bit 30: Comparator 6 output.

Allowed values:
0: Low: Non-inverting input below inverting input
1: High: Non-inverting input above inverting input

COMP6LOCK

Bit 31: Comparator 6 lock.

Allowed values:
0: Unlocked: Comparator CSR bits are read-write
1: Locked: Comparator CSR bits are read-only

COMP7_CSR

control and status register

Offset: 0x52, reset: 0, access: Unspecified

1/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMP7LOCK
rw 		COMP7OUT
r 		COMP7_BLANKING
rw 		COMP7HYST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
COMP7POL
rw 		COMP7OUTSEL
rw 		COMP7INPSEL
rw 		COMP7INMSEL
rw 		COMP7MODE
rw 		COMP7EN
rw
Toggle Fields.

COMP7EN

Bit 0: Comparator 7 enable.

COMP7MODE

Bits 2-3: Comparator 7 mode.

COMP7INMSEL

Bits 4-6: Comparator 7 inverting input selection.

COMP7INPSEL

Bit 7: Comparator 7 non inverted input.

COMP7OUTSEL

Bits 10-13: Comparator 7 output selection.

COMP7POL

Bit 15: Comparator 7 output polarity.

COMP7HYST

Bits 16-17: Comparator 7 hysteresis.

COMP7_BLANKING

Bits 18-20: Comparator 7 blanking source.

COMP7OUT

Bit 30: Comparator 7 output.

COMP7LOCK

Bit 31: Comparator 7 lock.

CRC

0x40023000: cyclic redundancy check calculation unit

8/8 fields covered. Toggle Registers.

DR

Data register

Offset: 0x0, reset: 0xFFFFFFFF, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DR
rw
Toggle Fields.

DR

Bits 0-31: Data register bits.

Allowed values: 0-4294967295

IDR

Independent data register

Offset: 0x4, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR
rw
Toggle Fields.

IDR

Bits 0-7: General-purpose 8-bit data register bits.

Allowed values: 0-255

CR

Control register

Offset: 0x8, reset: 0x00000000, access: read-write

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
REV_OUT
rw 		REV_IN
rw 		POLYSIZE
rw 		RESET
rw
Toggle Fields.

RESET

Bit 0: reset bit.

Allowed values:
1: Reset: Resets the CRC calculation unit and sets the data register to 0xFFFF FFFF

POLYSIZE

Bits 3-4: Polynomial size.

Allowed values:
0: Polysize32: 32-bit polynomial
1: Polysize16: 16-bit polynomial
2: Polysize8: 8-bit polynomial
3: Polysize7: 7-bit polynomial

REV_IN

Bits 5-6: Reverse input data.

Allowed values:
0: Normal: Bit order not affected
1: Byte: Bit reversal done by byte
2: HalfWord: Bit reversal done by half-word
3: Word: Bit reversal done by word

REV_OUT

Bit 7: Reverse output data.

Allowed values:
0: Normal: Bit order not affected
1: Reversed: Bit reversed output

INIT

Initial CRC value

Offset: 0x10, reset: 0xFFFFFFFF, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
INIT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
INIT
rw
Toggle Fields.

INIT

Bits 0-31: Programmable initial CRC value.

Allowed values: 0-4294967295

POL

CRC polynomial

Offset: 0x14, reset: 0x04C11DB7, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
POL
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
POL
rw
Toggle Fields.

POL

Bits 0-31: Programmable polynomial.

Allowed values: 0-4294967295

DAC1

0x40007400: Digital-to-analog converter

2/34 fields covered. Toggle Registers.

CR

control register

Offset: 0x0, reset: 0x00000000, access: read-write

0/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DMAUDRIE2
rw 		DMAEN2
rw 		MAMP2
rw 		WAVE2
rw 		TSEL2
rw 		TEN2
rw 		BOFF2
rw 		EN2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAUDRIE1
rw 		DMAEN1
rw 		MAMP1
rw 		WAVE1
rw 		TSEL1
rw 		TEN1
rw 		BOFF1
rw 		EN1
rw
Toggle Fields.

EN1

Bit 0: DAC channel1 enable.

BOFF1

Bit 1: DAC channel1 output buffer disable.

TEN1

Bit 2: DAC channel1 trigger enable.

TSEL1

Bits 3-5: DAC channel1 trigger selection.

WAVE1

Bits 6-7: DAC channel1 noise/triangle wave generation enable.

MAMP1

Bits 8-11: DAC channel1 mask/amplitude selector.

DMAEN1

Bit 12: DAC channel1 DMA enable.

DMAUDRIE1

Bit 13: DAC channel1 DMA Underrun Interrupt enable.

EN2

Bit 16: DAC channel2 enable.

BOFF2

Bit 17: DAC channel2 output buffer disable.

TEN2

Bit 18: DAC channel2 trigger enable.

TSEL2

Bits 19-21: DAC channel2 trigger selection.

WAVE2

Bits 22-23: DAC channel2 noise/triangle wave generation enable.

MAMP2

Bits 24-27: DAC channel2 mask/amplitude selector.

DMAEN2

Bit 28: DAC channel2 DMA enable.

DMAUDRIE2

Bit 29: DAC channel2 DMA underrun interrupt enable.

SWTRIGR

software trigger register

Offset: 0x4, reset: 0x00000000, access: write-only

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SWTRIG2
w 		SWTRIG1
w
Toggle Fields.

SWTRIG1

Bit 0: DAC channel1 software trigger.

SWTRIG2

Bit 1: DAC channel2 software trigger.

DHR12R1

channel1 12-bit right-aligned data holding register

Offset: 0x8, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 0-11: DAC channel1 12-bit right-aligned data.

DHR12L1

channel1 12-bit left aligned data holding register

Offset: 0xC, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 4-15: DAC channel1 12-bit left-aligned data.

DHR8R1

channel1 8-bit right aligned data holding register

Offset: 0x10, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 0-7: DAC channel1 8-bit right-aligned data.

DHR12R2

channel2 12-bit right aligned data holding register

Offset: 0x14, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC2DHR
rw
Toggle Fields.

DACC2DHR

Bits 0-11: DAC channel2 12-bit right-aligned data.

DHR12L2

channel2 12-bit left aligned data holding register

Offset: 0x18, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC2DHR
rw
Toggle Fields.

DACC2DHR

Bits 4-15: DAC channel2 12-bit left-aligned data.

DHR8R2

channel2 8-bit right-aligned data holding register

Offset: 0x1C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC2DHR
rw
Toggle Fields.

DACC2DHR

Bits 0-7: DAC channel2 8-bit right-aligned data.

DHR12RD

Dual DAC 12-bit right-aligned data holding register

Offset: 0x20, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DACC2DHR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 0-11: DAC channel1 12-bit right-aligned data.

DACC2DHR

Bits 16-27: DAC channel2 12-bit right-aligned data.

DHR12LD

DUAL DAC 12-bit left aligned data holding register

Offset: 0x24, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DACC2DHR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 4-15: DAC channel1 12-bit left-aligned data.

DACC2DHR

Bits 20-31: DAC channel2 12-bit left-aligned data.

DHR8RD

DUAL DAC 8-bit right aligned data holding register

Offset: 0x28, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC2DHR
rw 		DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 0-7: DAC channel1 8-bit right-aligned data.

DACC2DHR

Bits 8-15: DAC channel2 8-bit right-aligned data.

DOR1

channel1 data output register

Offset: 0x2C, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DOR
r
Toggle Fields.

DACC1DOR

Bits 0-11: DAC channel1 data output.

DOR2

channel2 data output register

Offset: 0x30, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC2DOR
r
Toggle Fields.

DACC2DOR

Bits 0-11: DAC channel2 data output.

SR

status register

Offset: 0x34, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DMAUDR2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAUDR1
rw
Toggle Fields.

DMAUDR1

Bit 13: DAC channel1 DMA underrun flag.

DMAUDR2

Bit 29: DAC channel2 DMA underrun flag.

DAC2

0x40009800: Digital-to-analog converter

1/18 fields covered. Toggle Registers.

CR

control register

Offset: 0x0, reset: 0x00000000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAUDRIE1
rw 		DMAEN1
rw 		MAMP13
rw 		MAMP12
rw 		MAMP11
rw 		MAMP10
rw 		WAVE1
rw 		WAVE2
rw 		TSEL1
rw 		TEN1
rw 		BOFF1
rw 		EN1
rw
Toggle Fields.

EN1

Bit 0: DAC channel1 enable.

BOFF1

Bit 1: DAC channel1 output buffer disable.

TEN1

Bit 2: DAC channel1 trigger enable.

TSEL1

Bits 3-5: DAC channel1 trigger selection.

WAVE2

Bit 6: WAVE2.

WAVE1

Bit 7: DAC channel1 noise/triangle wave generation enable.

MAMP10

Bit 8: MAMP10.

MAMP11

Bit 9: MAMP11.

MAMP12

Bit 10: MAMP12.

MAMP13

Bit 11: DAC channel1 mask/amplitude selector.

DMAEN1

Bit 12: DAC channel1 DMA enable.

DMAUDRIE1

Bit 13: DAC channel1 DMA Underrun Interrupt enable.

SWTRIGR

software trigger register

Offset: 0x4, reset: 0x00000000, access: write-only

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SWTRIG1
w
Toggle Fields.

SWTRIG1

Bit 0: DAC channel1 software trigger.

DHR12R1

channel1 12-bit right-aligned data holding register

Offset: 0x8, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 0-11: DAC channel1 12-bit right-aligned data.

DHR12L1

DAC channel1 12-bit left aligned data holding register

Offset: 0xC, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 4-15: DAC channel1 12-bit left-aligned data.

DHR8R1

DAC channel1 8-bit right aligned data holding register

Offset: 0x10, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DHR
rw
Toggle Fields.

DACC1DHR

Bits 0-7: DAC channel1 8-bit right-aligned data.

DOR1

DAC channel1 data output register

Offset: 0x2C, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DACC1DOR
r
Toggle Fields.

DACC1DOR

Bits 0-11: DAC channel1 data output.

SR

DAC status register

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAUDR1
rw
Toggle Fields.

DMAUDR1

Bit 13: DAC channel1 DMA underrun flag.

DBGMCU

0xE0042000: Debug support

2/27 fields covered. Toggle Registers.

IDCODE

MCU Device ID Code Register

Offset: 0x0, reset: 0x0, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
REV_ID
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DEV_ID
r
Toggle Fields.

DEV_ID

Bits 0-11: Device Identifier.

REV_ID

Bits 16-31: Revision Identifier.

CR

Debug MCU Configuration Register

Offset: 0x4, reset: 0x0, access: read-write

0/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TRACE_MODE
rw 		TRACE_IOEN
rw 		DBG_STANDBY
rw 		DBG_STOP
rw 		DBG_SLEEP
rw
Toggle Fields.

DBG_SLEEP

Bit 0: Debug Sleep mode.

DBG_STOP

Bit 1: Debug Stop Mode.

DBG_STANDBY

Bit 2: Debug Standby Mode.

TRACE_IOEN

Bit 5: Trace pin assignment control.

TRACE_MODE

Bits 6-7: Trace pin assignment control.

APB1_FZ

APB Low Freeze Register

Offset: 0x8, reset: 0x0, access: read-write

0/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DBG_CAN_STOP
rw 		I2C2_SMBUS_TIMEOUT
rw 		I2C1_SMBUS_TIMEOUT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBG_IWDG_STOP
rw 		DBG_WWDG_STOP
rw 		DBG_RTC_STOP
rw 		DBG_TIM18_STOP
rw 		DBG_TIMER14_STOP
rw 		DBG_TIM13_STOP
rw 		DBG_TIM12_STOP
rw 		DBG_TIM7_STOP
rw 		DBG_TIM6_STOP
rw 		DBG_TIM5_STOP
rw 		DBG_TIM4_STOP
rw 		DBG_TIM3_STOP
rw 		DBG_TIM2_STOP
rw
Toggle Fields.

DBG_TIM2_STOP

Bit 0: Debug Timer 2 stopped when Core is halted.

DBG_TIM3_STOP

Bit 1: Debug Timer 3 stopped when Core is halted.

DBG_TIM4_STOP

Bit 2: Debug Timer 4 stopped when Core is halted.

DBG_TIM5_STOP

Bit 3: Debug Timer 5 stopped when Core is halted.

DBG_TIM6_STOP

Bit 4: Debug Timer 6 stopped when Core is halted.

DBG_TIM7_STOP

Bit 5: Debug Timer 7 stopped when Core is halted.

DBG_TIM12_STOP

Bit 6: Debug Timer 12 stopped when Core is halted.

DBG_TIM13_STOP

Bit 7: Debug Timer 13 stopped when Core is halted.

DBG_TIMER14_STOP

Bit 8: Debug Timer 14 stopped when Core is halted.

DBG_TIM18_STOP

Bit 9: Debug Timer 18 stopped when Core is halted.

DBG_RTC_STOP

Bit 10: Debug RTC stopped when Core is halted.

DBG_WWDG_STOP

Bit 11: Debug Window Wachdog stopped when Core is halted.

DBG_IWDG_STOP

Bit 12: Debug Independent Wachdog stopped when Core is halted.

I2C1_SMBUS_TIMEOUT

Bit 21: SMBUS timeout mode stopped when Core is halted.

I2C2_SMBUS_TIMEOUT

Bit 22: SMBUS timeout mode stopped when Core is halted.

DBG_CAN_STOP

Bit 25: Debug CAN stopped when core is halted.

APB2FZ

APB High Freeze Register

Offset: 0xC, reset: 0x0, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBG_TIM19_STOP
rw 		DBG_TIM17_STO
rw 		DBG_TIM16_STOP
rw 		DBG_TIM15_STOP
rw
Toggle Fields.

DBG_TIM15_STOP

Bit 2: Debug Timer 15 stopped when Core is halted.

DBG_TIM16_STOP

Bit 3: Debug Timer 16 stopped when Core is halted.

DBG_TIM17_STO

Bit 4: Debug Timer 17 stopped when Core is halted.

DBG_TIM19_STOP

Bit 5: Debug Timer 19 stopped when Core is halted.

DMA1

0x40020000: DMA controller 1

69/71 fields covered. Toggle Registers.

CR

DMA channel configuration register (DMA_CCR)

Offset: 0x0, reset: 0x00000000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MEM2MEM
rw 		PL
rw 		MSIZE
rw 		PSIZE
rw 		MINC
rw 		PINC
rw 		CIRC
rw 		DIR
rw 		TEIE
rw 		HTIE
rw 		TCIE
rw 		EN
rw
Toggle Fields.

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR

DMA channel 1 number of data register

Offset: 0x4, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
NDT
rw
Toggle Fields.

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0-65535

PAR

DMA channel 1 peripheral address register

Offset: 0x8, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PA
rw
Toggle Fields.

PA

Bits 0-31: Peripheral address.

MAR

DMA channel 1 memory address register

Offset: 0xC, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MA
rw
Toggle Fields.

MA

Bits 0-31: Memory address.

DMA2

0x40020400: DMA controller 1

69/71 fields covered. Toggle Registers.

CR

DMA channel configuration register (DMA_CCR)

Offset: 0x0, reset: 0x00000000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MEM2MEM
rw 		PL
rw 		MSIZE
rw 		PSIZE
rw 		MINC
rw 		PINC
rw 		CIRC
rw 		DIR
rw 		TEIE
rw 		HTIE
rw 		TCIE
rw 		EN
rw
Toggle Fields.

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR

DMA channel 1 number of data register

Offset: 0x4, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
NDT
rw
Toggle Fields.

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0-65535

PAR

DMA channel 1 peripheral address register

Offset: 0x8, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PA
rw
Toggle Fields.

PA

Bits 0-31: Peripheral address.

MAR

DMA channel 1 memory address register

Offset: 0xC, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MA
rw
Toggle Fields.

MA

Bits 0-31: Memory address.

EXTI

0x40010400: External interrupt/event controller

134/134 fields covered. Toggle Registers.

IMR

Interrupt mask register (EXTI_IMR)

Offset: 0x0, reset: 0x1F800000, access: read-write

29/29 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MR28
rw 		MR27
rw 		MR26
rw 		MR25
rw 		MR24
rw 		MR23
rw 		MR22
rw 		MR21
rw 		MR20
rw 		MR19
rw 		MR18
rw 		MR17
rw 		MR16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MR15
rw 		MR14
rw 		MR13
rw 		MR12
rw 		MR11
rw 		MR10
rw 		MR9
rw 		MR8
rw 		MR7
rw 		MR6
rw 		MR5
rw 		MR4
rw 		MR3
rw 		MR2
rw 		MR1
rw 		MR0
rw
Toggle Fields.

MR0

Bit 0: Interrupt Mask on line 0.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR1

Bit 1: Interrupt Mask on line 1.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR2

Bit 2: Interrupt Mask on line 2.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR3

Bit 3: Interrupt Mask on line 3.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR4

Bit 4: Interrupt Mask on line 4.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR5

Bit 5: Interrupt Mask on line 5.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR6

Bit 6: Interrupt Mask on line 6.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR7

Bit 7: Interrupt Mask on line 7.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR8

Bit 8: Interrupt Mask on line 8.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR9

Bit 9: Interrupt Mask on line 9.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR10

Bit 10: Interrupt Mask on line 10.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR11

Bit 11: Interrupt Mask on line 11.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR12

Bit 12: Interrupt Mask on line 12.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR13

Bit 13: Interrupt Mask on line 13.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR14

Bit 14: Interrupt Mask on line 14.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR15

Bit 15: Interrupt Mask on line 15.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR16

Bit 16: Interrupt Mask on line 16.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR17

Bit 17: Interrupt Mask on line 17.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR18

Bit 18: Interrupt Mask on line 18.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR19

Bit 19: Interrupt Mask on line 19.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR20

Bit 20: Interrupt Mask on line 20.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR21

Bit 21: Interrupt Mask on line 21.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR22

Bit 22: Interrupt Mask on line 22.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR23

Bit 23: Interrupt Mask on line 23.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR24

Bit 24: Interrupt Mask on line 24.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR25

Bit 25: Interrupt Mask on line 25.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR26

Bit 26: Interrupt Mask on line 26.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR27

Bit 27: Interrupt Mask on line 27.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR28

Bit 28: Interrupt Mask on line 28.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EMR

Event mask register (EXTI_EMR)

Offset: 0x4, reset: 0x00000000, access: read-write

29/29 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MR28
rw 		MR27
rw 		MR26
rw 		MR25
rw 		MR24
rw 		MR23
rw 		MR22
rw 		MR21
rw 		MR20
rw 		MR19
rw 		MR18
rw 		MR17
rw 		MR16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MR15
rw 		MR14
rw 		MR13
rw 		MR12
rw 		MR11
rw 		MR10
rw 		MR9
rw 		MR8
rw 		MR7
rw 		MR6
rw 		MR5
rw 		MR4
rw 		MR3
rw 		MR2
rw 		MR1
rw 		MR0
rw
Toggle Fields.

MR0

Bit 0: Event Mask on line 0.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR1

Bit 1: Event Mask on line 1.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR2

Bit 2: Event Mask on line 2.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR3

Bit 3: Event Mask on line 3.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR4

Bit 4: Event Mask on line 4.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR5

Bit 5: Event Mask on line 5.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR6

Bit 6: Event Mask on line 6.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR7

Bit 7: Event Mask on line 7.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR8

Bit 8: Event Mask on line 8.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR9

Bit 9: Event Mask on line 9.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR10

Bit 10: Event Mask on line 10.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR11

Bit 11: Event Mask on line 11.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR12

Bit 12: Event Mask on line 12.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR13

Bit 13: Event Mask on line 13.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR14

Bit 14: Event Mask on line 14.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR15

Bit 15: Event Mask on line 15.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR16

Bit 16: Event Mask on line 16.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR17

Bit 17: Event Mask on line 17.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR18

Bit 18: Event Mask on line 18.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR19

Bit 19: Event Mask on line 19.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR20

Bit 20: Event Mask on line 20.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR21

Bit 21: Event Mask on line 21.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR22

Bit 22: Event Mask on line 22.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR23

Bit 23: Event Mask on line 23.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR24

Bit 24: Event Mask on line 24.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR25

Bit 25: Event Mask on line 25.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR26

Bit 26: Event Mask on line 26.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR27

Bit 27: Event Mask on line 27.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR28

Bit 28: Event Mask on line 28.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

RTSR

Rising Trigger selection register (EXTI_RTSR)

Offset: 0x8, reset: 0x00000000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TR19
rw 		TR17
rw 		TR16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TR15
rw 		TR14
rw 		TR13
rw 		TR12
rw 		TR11
rw 		TR10
rw 		TR9
rw 		TR8
rw 		TR7
rw 		TR6
rw 		TR5
rw 		TR4
rw 		TR3
rw 		TR2
rw 		TR1
rw 		TR0
rw
Toggle Fields.

TR0

Bit 0: Rising trigger event configuration of line 0.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR1

Bit 1: Rising trigger event configuration of line 1.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR2

Bit 2: Rising trigger event configuration of line 2.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR3

Bit 3: Rising trigger event configuration of line 3.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR4

Bit 4: Rising trigger event configuration of line 4.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR5

Bit 5: Rising trigger event configuration of line 5.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR6

Bit 6: Rising trigger event configuration of line 6.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR7

Bit 7: Rising trigger event configuration of line 7.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR8

Bit 8: Rising trigger event configuration of line 8.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR9

Bit 9: Rising trigger event configuration of line 9.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR10

Bit 10: Rising trigger event configuration of line 10.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR11

Bit 11: Rising trigger event configuration of line 11.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR12

Bit 12: Rising trigger event configuration of line 12.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR13

Bit 13: Rising trigger event configuration of line 13.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR14

Bit 14: Rising trigger event configuration of line 14.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR15

Bit 15: Rising trigger event configuration of line 15.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR16

Bit 16: Rising trigger event configuration of line 16.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR17

Bit 17: Rising trigger event configuration of line 17.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR19

Bit 19: Rising trigger event configuration of line 19.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

FTSR

Falling Trigger selection register (EXTI_FTSR)

Offset: 0xC, reset: 0x00000000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TR19
rw 		TR17
rw 		TR16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TR15
rw 		TR14
rw 		TR13
rw 		TR12
rw 		TR11
rw 		TR10
rw 		TR9
rw 		TR8
rw 		TR7
rw 		TR6
rw 		TR5
rw 		TR4
rw 		TR3
rw 		TR2
rw 		TR1
rw 		TR0
rw
Toggle Fields.

TR0

Bit 0: Falling trigger event configuration of line 0.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR1

Bit 1: Falling trigger event configuration of line 1.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR2

Bit 2: Falling trigger event configuration of line 2.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR3

Bit 3: Falling trigger event configuration of line 3.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR4

Bit 4: Falling trigger event configuration of line 4.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR5

Bit 5: Falling trigger event configuration of line 5.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR6

Bit 6: Falling trigger event configuration of line 6.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR7

Bit 7: Falling trigger event configuration of line 7.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR8

Bit 8: Falling trigger event configuration of line 8.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR9

Bit 9: Falling trigger event configuration of line 9.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR10

Bit 10: Falling trigger event configuration of line 10.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR11

Bit 11: Falling trigger event configuration of line 11.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR12

Bit 12: Falling trigger event configuration of line 12.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR13

Bit 13: Falling trigger event configuration of line 13.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR14

Bit 14: Falling trigger event configuration of line 14.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR15

Bit 15: Falling trigger event configuration of line 15.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR16

Bit 16: Falling trigger event configuration of line 16.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR17

Bit 17: Falling trigger event configuration of line 17.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR19

Bit 19: Falling trigger event configuration of line 19.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

SWIER

Software interrupt event register (EXTI_SWIER)

Offset: 0x10, reset: 0x00000000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SWIER19
rw 		SWIER17
rw 		SWIER16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SWIER15
rw 		SWIER14
rw 		SWIER13
rw 		SWIER12
rw 		SWIER11
rw 		SWIER10
rw 		SWIER9
rw 		SWIER8
rw 		SWIER7
rw 		SWIER6
rw 		SWIER5
rw 		SWIER4
rw 		SWIER3
rw 		SWIER2
rw 		SWIER1
rw 		SWIER0
rw
Toggle Fields.

SWIER0

Bit 0: Software Interrupt on line 0.

Allowed values:
1: Pend: Generates an interrupt request

SWIER1

Bit 1: Software Interrupt on line 1.

Allowed values:
1: Pend: Generates an interrupt request

SWIER2

Bit 2: Software Interrupt on line 2.

Allowed values:
1: Pend: Generates an interrupt request

SWIER3

Bit 3: Software Interrupt on line 3.

Allowed values:
1: Pend: Generates an interrupt request

SWIER4

Bit 4: Software Interrupt on line 4.

Allowed values:
1: Pend: Generates an interrupt request

SWIER5

Bit 5: Software Interrupt on line 5.

Allowed values:
1: Pend: Generates an interrupt request

SWIER6

Bit 6: Software Interrupt on line 6.

Allowed values:
1: Pend: Generates an interrupt request

SWIER7

Bit 7: Software Interrupt on line 7.

Allowed values:
1: Pend: Generates an interrupt request

SWIER8

Bit 8: Software Interrupt on line 8.

Allowed values:
1: Pend: Generates an interrupt request

SWIER9

Bit 9: Software Interrupt on line 9.

Allowed values:
1: Pend: Generates an interrupt request

SWIER10

Bit 10: Software Interrupt on line 10.

Allowed values:
1: Pend: Generates an interrupt request

SWIER11

Bit 11: Software Interrupt on line 11.

Allowed values:
1: Pend: Generates an interrupt request

SWIER12

Bit 12: Software Interrupt on line 12.

Allowed values:
1: Pend: Generates an interrupt request

SWIER13

Bit 13: Software Interrupt on line 13.

Allowed values:
1: Pend: Generates an interrupt request

SWIER14

Bit 14: Software Interrupt on line 14.

Allowed values:
1: Pend: Generates an interrupt request

SWIER15

Bit 15: Software Interrupt on line 15.

Allowed values:
1: Pend: Generates an interrupt request

SWIER16

Bit 16: Software Interrupt on line 16.

Allowed values:
1: Pend: Generates an interrupt request

SWIER17

Bit 17: Software Interrupt on line 17.

Allowed values:
1: Pend: Generates an interrupt request

SWIER19

Bit 19: Software Interrupt on line 19.

Allowed values:
1: Pend: Generates an interrupt request

PR

Pending register (EXTI_PR)

Offset: 0x14, reset: 0x00000000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PR19
rw 		PR17
rw 		PR16
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PR15
rw 		PR14
rw 		PR13
rw 		PR12
rw 		PR11
rw 		PR10
rw 		PR9
rw 		PR8
rw 		PR7
rw 		PR6
rw 		PR5
rw 		PR4
rw 		PR3
rw 		PR2
rw 		PR1
rw 		PR0
rw
Toggle Fields.

PR0

Bit 0: Pending bit 0.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR1

Bit 1: Pending bit 1.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR2

Bit 2: Pending bit 2.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR3

Bit 3: Pending bit 3.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR4

Bit 4: Pending bit 4.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR5

Bit 5: Pending bit 5.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR6

Bit 6: Pending bit 6.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR7

Bit 7: Pending bit 7.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR8

Bit 8: Pending bit 8.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR9

Bit 9: Pending bit 9.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR10

Bit 10: Pending bit 10.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR11

Bit 11: Pending bit 11.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR12

Bit 12: Pending bit 12.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR13

Bit 13: Pending bit 13.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR14

Bit 14: Pending bit 14.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR15

Bit 15: Pending bit 15.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR16

Bit 16: Pending bit 16.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR17

Bit 17: Pending bit 17.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR19

Bit 19: Pending bit 19.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FLASH

0x40022000: Flash

34/34 fields covered. Toggle Registers.

ACR

Flash access control register

Offset: 0x0, reset: 0x00000030, access: Unspecified

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PRFTBS
r 		PRFTBE
rw 		HLFCYA
rw 		LATENCY
rw
Toggle Fields.

LATENCY

Bits 0-2: LATENCY.

Allowed values:
0: WS0: 0 wait states, if 0 < HCLK <= 24 MHz
1: WS1: 1 wait state, if 24 < HCLK <= 48 MHz
2: WS2: 2 wait states, if 48 < HCLK <= 72 MHz

HLFCYA

Bit 3: Flash half cycle access enable.

Allowed values:
0: Disabled: Half cycle is disabled
1: Enabled: Half cycle is enabled

PRFTBE

Bit 4: PRFTBE.

Allowed values:
0: Disabled: Prefetch is disabled
1: Enabled: Prefetch is enabled

PRFTBS

Bit 5: PRFTBS.

Allowed values:
0: Disabled: Prefetch buffer is disabled
1: Enabled: Prefetch buffer is enabled

KEYR

Flash key register

Offset: 0x4, reset: 0x00000000, access: write-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FKEYR
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FKEYR
w
Toggle Fields.

FKEYR

Bits 0-31: Flash Key.

Allowed values: 0-4294967295

OPTKEYR

Flash option key register

Offset: 0x8, reset: 0x00000000, access: write-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OPTKEYR
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OPTKEYR
w
Toggle Fields.

OPTKEYR

Bits 0-31: Option byte key.

Allowed values: 0-4294967295

SR

Flash status register

Offset: 0xC, reset: 0x00000000, access: Unspecified

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EOP
rw 		WRPRTERR
rw 		PGERR
rw 		BSY
r
Toggle Fields.

BSY

Bit 0: Busy.

Allowed values:
0: Inactive: No write/erase operation is in progress
1: Active: No write/erase operation is in progress

PGERR

Bit 2: Programming error.

Allowed values:
0: NoError: No programming error occurred
1: Error: A programming error occurred

WRPRTERR

Bit 4: Write protection error.

Allowed values:
0: NoError: No write protection error occurred
1: Error: A write protection error occurred

EOP

Bit 5: End of operation.

Allowed values:
0: NoEvent: No EOP event occurred
1: Event: An EOP event occurred

CR

Flash control register

Offset: 0x10, reset: 0x00000080, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OBL_LAUNCH
rw 		EOPIE
rw 		ERRIE
rw 		OPTWRE
rw 		LOCK
rw 		STRT
rw 		OPTER
rw 		OPTPG
rw 		MER
rw 		PER
rw 		PG
rw
Toggle Fields.

PG

Bit 0: Programming.

Allowed values:
1: Program: Flash programming activated

PER

Bit 1: Page erase.

Allowed values:
1: PageErase: Erase activated for selected page

MER

Bit 2: Mass erase.

Allowed values:
1: MassErase: Erase activated for all user sectors

OPTPG

Bit 4: Option byte programming.

Allowed values:
1: OptionByteProgramming: Program option byte activated

OPTER

Bit 5: Option byte erase.

Allowed values:
1: OptionByteErase: Erase option byte activated

STRT

Bit 6: Start.

Allowed values:
1: Start: Trigger an erase operation

LOCK

Bit 7: Lock.

Allowed values:
0: Unlocked: FLASH_CR register is unlocked
1: Locked: FLASH_CR register is locked

OPTWRE

Bit 9: Option bytes write enable.

Allowed values:
0: Disabled: Option byte write enabled
1: Enabled: Option byte write disabled

ERRIE

Bit 10: Error interrupt enable.

Allowed values:
0: Disabled: Error interrupt generation disabled
1: Enabled: Error interrupt generation enabled

EOPIE

Bit 12: End of operation interrupt enable.

Allowed values:
0: Disabled: End of operation interrupt disabled
1: Enabled: End of operation interrupt enabled

OBL_LAUNCH

Bit 13: Force option byte loading.

Allowed values:
0: Inactive: Force option byte loading inactive
1: Active: Force option byte loading active

AR

Flash address register

Offset: 0x14, reset: 0x00000000, access: write-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FAR
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FAR
w
Toggle Fields.

FAR

Bits 0-31: Flash address.

Allowed values: 0-4294967295

OBR

Option byte register

Offset: 0x1C, reset: 0xFFFFFF02, access: read-only

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
Data1
r 		Data0
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SDADC12_VDD_MONITOR
r 		SRAM_PARITY_CHECK
r 		VDDA_MONITOR
r 		nBOOT1
r 		nRST_STDBY
r 		nRST_STOP
r 		WDG_SW
r 		RDPRT
r 		OPTERR
r
Toggle Fields.

OPTERR

Bit 0: Option byte error.

Allowed values:
1: OptionByteError: The loaded option byte and its complement do not match

RDPRT

Bits 1-2: Read protection Level status.

Allowed values:
0: Level0: Level 0
1: Level1: Level 1
3: Level2: Level 2

WDG_SW

Bit 8: WDG_SW.

Allowed values:
0: Hardware: Hardware watchdog
1: Software: Software watchdog

nRST_STOP

Bit 9: nRST_STOP.

Allowed values:
0: Reset: Reset generated when entering Stop mode
1: NoReset: No reset generated

nRST_STDBY

Bit 10: nRST_STDBY.

Allowed values:
0: Reset: Reset generated when entering Standby mode
1: NoReset: No reset generated

nBOOT1

Bit 12: BOOT1.

Allowed values:
0: Disabled: Together with BOOT0, select the device boot mode
1: Enabled: Together with BOOT0, select the device boot mode

VDDA_MONITOR

Bit 13: VDDA_MONITOR.

Allowed values:
0: Disabled: VDDA power supply supervisor disabled
1: Enabled: VDDA power supply supervisor enabled

SRAM_PARITY_CHECK

Bit 14: SRAM_PARITY_CHECK.

SDADC12_VDD_MONITOR

Bit 15: SDADC12_VDD_MONITOR.

Data0

Bits 16-23: Data0.

Allowed values: 0-255

Data1

Bits 24-31: Data1.

Allowed values: 0-255

WRPR

Write protection register

Offset: 0x20, reset: 0xFFFFFFFF, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WRP
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
WRP
r
Toggle Fields.

WRP

Bits 0-31: Write protect.

Allowed values: 0-4294967295

FMC

0xA0000400: Flexible memory controller

5/187 fields covered. Toggle Registers.

BCR1

SRAM/NOR-Flash chip-select control register 1

Offset: 0x0, reset: 0x000030D0, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CCLKEN
rw 		CBURSTRW
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ASYNCWAIT
rw 		EXTMOD
rw 		WAITEN
rw 		WREN
rw 		WAITCFG
rw 		WAITPOL
rw 		BURSTEN
rw 		FACCEN
rw 		MWID
rw 		MTYP
rw 		MUXEN
rw 		MBKEN
rw
Toggle Fields.

MBKEN

Bit 0: MBKEN.

MUXEN

Bit 1: MUXEN.

MTYP

Bits 2-3: MTYP.

MWID

Bits 4-5: MWID.

FACCEN

Bit 6: FACCEN.

BURSTEN

Bit 8: BURSTEN.

WAITPOL

Bit 9: WAITPOL.

WAITCFG

Bit 11: WAITCFG.

WREN

Bit 12: WREN.

WAITEN

Bit 13: WAITEN.

EXTMOD

Bit 14: EXTMOD.

ASYNCWAIT

Bit 15: ASYNCWAIT.

CBURSTRW

Bit 19: CBURSTRW.

CCLKEN

Bit 20: CCLKEN.

BTR1

SRAM/NOR-Flash chip-select timing register 1

Offset: 0x4, reset: 0xFFFFFFFF, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACCMOD
rw 		DATLAT
rw 		CLKDIV
rw 		BUSTURN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATAST
rw 		ADDHLD
rw 		ADDSET
rw
Toggle Fields.

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: BUSTURN.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BCR2

SRAM/NOR-Flash chip-select control register 2

Offset: 0x8, reset: 0x000030D0, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CBURSTRW
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ASYNCWAIT
rw 		EXTMOD
rw 		WAITEN
rw 		WREN
rw 		WAITCFG
rw 		WRAPMOD
rw 		WAITPOL
rw 		BURSTEN
rw 		FACCEN
rw 		MWID
rw 		MTYP
rw 		MUXEN
rw 		MBKEN
rw
Toggle Fields.

MBKEN

Bit 0: MBKEN.

MUXEN

Bit 1: MUXEN.

MTYP

Bits 2-3: MTYP.

MWID

Bits 4-5: MWID.

FACCEN

Bit 6: FACCEN.

BURSTEN

Bit 8: BURSTEN.

WAITPOL

Bit 9: WAITPOL.

WRAPMOD

Bit 10: WRAPMOD.

WAITCFG

Bit 11: WAITCFG.

WREN

Bit 12: WREN.

WAITEN

Bit 13: WAITEN.

EXTMOD

Bit 14: EXTMOD.

ASYNCWAIT

Bit 15: ASYNCWAIT.

CBURSTRW

Bit 19: CBURSTRW.

BTR2

SRAM/NOR-Flash chip-select timing register 2

Offset: 0xC, reset: 0xFFFFFFFF, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACCMOD
rw 		DATLAT
rw 		CLKDIV
rw 		BUSTURN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATAST
rw 		ADDHLD
rw 		ADDSET
rw
Toggle Fields.

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: BUSTURN.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BCR3

SRAM/NOR-Flash chip-select control register 3

Offset: 0x10, reset: 0x000030D0, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CBURSTRW
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ASYNCWAIT
rw 		EXTMOD
rw 		WAITEN
rw 		WREN
rw 		WAITCFG
rw 		WRAPMOD
rw 		WAITPOL
rw 		BURSTEN
rw 		FACCEN
rw 		MWID
rw 		MTYP
rw 		MUXEN
rw 		MBKEN
rw
Toggle Fields.

MBKEN

Bit 0: MBKEN.

MUXEN

Bit 1: MUXEN.

MTYP

Bits 2-3: MTYP.

MWID

Bits 4-5: MWID.

FACCEN

Bit 6: FACCEN.

BURSTEN

Bit 8: BURSTEN.

WAITPOL

Bit 9: WAITPOL.

WRAPMOD

Bit 10: WRAPMOD.

WAITCFG

Bit 11: WAITCFG.

WREN

Bit 12: WREN.

WAITEN

Bit 13: WAITEN.

EXTMOD

Bit 14: EXTMOD.

ASYNCWAIT

Bit 15: ASYNCWAIT.

CBURSTRW

Bit 19: CBURSTRW.

BTR3

SRAM/NOR-Flash chip-select timing register 3

Offset: 0x14, reset: 0xFFFFFFFF, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACCMOD
rw 		DATLAT
rw 		CLKDIV
rw 		BUSTURN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATAST
rw 		ADDHLD
rw 		ADDSET
rw
Toggle Fields.

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: BUSTURN.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BCR4

SRAM/NOR-Flash chip-select control register 4

Offset: 0x18, reset: 0x000030D0, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CBURSTRW
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ASYNCWAIT
rw 		EXTMOD
rw 		WAITEN
rw 		WREN
rw 		WAITCFG
rw 		WRAPMOD
rw 		WAITPOL
rw 		BURSTEN
rw 		FACCEN
rw 		MWID
rw 		MTYP
rw 		MUXEN
rw 		MBKEN
rw
Toggle Fields.

MBKEN

Bit 0: MBKEN.

MUXEN

Bit 1: MUXEN.

MTYP

Bits 2-3: MTYP.

MWID

Bits 4-5: MWID.

FACCEN

Bit 6: FACCEN.

BURSTEN

Bit 8: BURSTEN.

WAITPOL

Bit 9: WAITPOL.

WRAPMOD

Bit 10: WRAPMOD.

WAITCFG

Bit 11: WAITCFG.

WREN

Bit 12: WREN.

WAITEN

Bit 13: WAITEN.

EXTMOD

Bit 14: EXTMOD.

ASYNCWAIT

Bit 15: ASYNCWAIT.

CBURSTRW

Bit 19: CBURSTRW.

BTR4

SRAM/NOR-Flash chip-select timing register 4

Offset: 0x1C, reset: 0xFFFFFFFF, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACCMOD
rw 		DATLAT
rw 		CLKDIV
rw 		BUSTURN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATAST
rw 		ADDHLD
rw 		ADDSET
rw
Toggle Fields.

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: BUSTURN.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

PCR2

PC Card/NAND Flash control register 2

Offset: 0x60, reset: 0x00000018, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ECCPS
rw 		TAR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TAR
rw 		TCLR
rw 		ECCEN
rw 		PWID
rw 		PTYP
rw 		PBKEN
rw 		PWAITEN
rw
Toggle Fields.

PWAITEN

Bit 1: PWAITEN.

PBKEN

Bit 2: PBKEN.

PTYP

Bit 3: PTYP.

PWID

Bits 4-5: PWID.

ECCEN

Bit 6: ECCEN.

TCLR

Bits 9-12: TCLR.

TAR

Bits 13-16: TAR.

ECCPS

Bits 17-19: ECCPS.

SR2

FIFO status and interrupt register 2

Offset: 0x64, reset: 0x00000040, access: Unspecified

1/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FEMPT
r 		IFEN
rw 		ILEN
rw 		IREN
rw 		IFS
rw 		ILS
rw 		IRS
rw
Toggle Fields.

IRS

Bit 0: IRS.

ILS

Bit 1: ILS.

IFS

Bit 2: IFS.

IREN

Bit 3: IREN.

ILEN

Bit 4: ILEN.

IFEN

Bit 5: IFEN.

FEMPT

Bit 6: FEMPT.

PMEM2

Common memory space timing register 2

Offset: 0x68, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MEMHIZx
rw 		MEMHOLDx
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MEMWAITx
rw 		MEMSETx
rw
Toggle Fields.

MEMSETx

Bits 0-7: MEMSETx.

MEMWAITx

Bits 8-15: MEMWAITx.

MEMHOLDx

Bits 16-23: MEMHOLDx.

MEMHIZx

Bits 24-31: MEMHIZx.

PATT2

Attribute memory space timing register 2

Offset: 0x6C, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ATTHIZx
rw 		ATTHOLDx
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ATTWAITx
rw 		ATTSETx
rw
Toggle Fields.

ATTSETx

Bits 0-7: ATTSETx.

ATTWAITx

Bits 8-15: ATTWAITx.

ATTHOLDx

Bits 16-23: ATTHOLDx.

ATTHIZx

Bits 24-31: ATTHIZx.

ECCR2

ECC result register 2

Offset: 0x74, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ECCx
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ECCx
r
Toggle Fields.

ECCx

Bits 0-31: ECCx.

PCR3

PC Card/NAND Flash control register 3

Offset: 0x80, reset: 0x00000018, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ECCPS
rw 		TAR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TAR
rw 		TCLR
rw 		ECCEN
rw 		PWID
rw 		PTYP
rw 		PBKEN
rw 		PWAITEN
rw
Toggle Fields.

PWAITEN

Bit 1: PWAITEN.

PBKEN

Bit 2: PBKEN.

PTYP

Bit 3: PTYP.

PWID

Bits 4-5: PWID.

ECCEN

Bit 6: ECCEN.

TCLR

Bits 9-12: TCLR.

TAR

Bits 13-16: TAR.

ECCPS

Bits 17-19: ECCPS.

SR3

FIFO status and interrupt register 3

Offset: 0x84, reset: 0x00000040, access: Unspecified

1/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FEMPT
r 		IFEN
rw 		ILEN
rw 		IREN
rw 		IFS
rw 		ILS
rw 		IRS
rw
Toggle Fields.

IRS

Bit 0: IRS.

ILS

Bit 1: ILS.

IFS

Bit 2: IFS.

IREN

Bit 3: IREN.

ILEN

Bit 4: ILEN.

IFEN

Bit 5: IFEN.

FEMPT

Bit 6: FEMPT.

PMEM3

Common memory space timing register 3

Offset: 0x88, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MEMHIZx
rw 		MEMHOLDx
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MEMWAITx
rw 		MEMSETx
rw
Toggle Fields.

MEMSETx

Bits 0-7: MEMSETx.

MEMWAITx

Bits 8-15: MEMWAITx.

MEMHOLDx

Bits 16-23: MEMHOLDx.

MEMHIZx

Bits 24-31: MEMHIZx.

PATT3

Attribute memory space timing register 3

Offset: 0x8C, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ATTHIZx
rw 		ATTHOLDx
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ATTWAITx
rw 		ATTSETx
rw
Toggle Fields.

ATTSETx

Bits 0-7: ATTSETx.

ATTWAITx

Bits 8-15: ATTWAITx.

ATTHOLDx

Bits 16-23: ATTHOLDx.

ATTHIZx

Bits 24-31: ATTHIZx.

ECCR3

ECC result register 3

Offset: 0x94, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ECCx
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ECCx
r
Toggle Fields.

ECCx

Bits 0-31: ECCx.

PCR4

PC Card/NAND Flash control register 4

Offset: 0xA0, reset: 0x00000018, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ECCPS
rw 		TAR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TAR
rw 		TCLR
rw 		ECCEN
rw 		PWID
rw 		PTYP
rw 		PBKEN
rw 		PWAITEN
rw
Toggle Fields.

PWAITEN

Bit 1: PWAITEN.

PBKEN

Bit 2: PBKEN.

PTYP

Bit 3: PTYP.

PWID

Bits 4-5: PWID.

ECCEN

Bit 6: ECCEN.

TCLR

Bits 9-12: TCLR.

TAR

Bits 13-16: TAR.

ECCPS

Bits 17-19: ECCPS.

SR4

FIFO status and interrupt register 4

Offset: 0xA4, reset: 0x00000040, access: Unspecified

1/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FEMPT
r 		IFEN
rw 		ILEN
rw 		IREN
rw 		IFS
rw 		ILS
rw 		IRS
rw
Toggle Fields.

IRS

Bit 0: IRS.

ILS

Bit 1: ILS.

IFS

Bit 2: IFS.

IREN

Bit 3: IREN.

ILEN

Bit 4: ILEN.

IFEN

Bit 5: IFEN.

FEMPT

Bit 6: FEMPT.

PMEM4

Common memory space timing register 4

Offset: 0xA8, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MEMHIZx
rw 		MEMHOLDx
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MEMWAITx
rw 		MEMSETx
rw
Toggle Fields.

MEMSETx

Bits 0-7: MEMSETx.

MEMWAITx

Bits 8-15: MEMWAITx.

MEMHOLDx

Bits 16-23: MEMHOLDx.

MEMHIZx

Bits 24-31: MEMHIZx.

PATT4

Attribute memory space timing register 4

Offset: 0xAC, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ATTHIZx
rw 		ATTHOLDx
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ATTWAITx
rw 		ATTSETx
rw
Toggle Fields.

ATTSETx

Bits 0-7: ATTSETx.

ATTWAITx

Bits 8-15: ATTWAITx.

ATTHOLDx

Bits 16-23: ATTHOLDx.

ATTHIZx

Bits 24-31: ATTHIZx.

PIO4

I/O space timing register 4

Offset: 0xB0, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IOHIZx
rw 		IOHOLDx
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IOWAITx
rw 		IOSETx
rw
Toggle Fields.

IOSETx

Bits 0-7: IOSETx.

IOWAITx

Bits 8-15: IOWAITx.

IOHOLDx

Bits 16-23: IOHOLDx.

IOHIZx

Bits 24-31: IOHIZx.

BWTR1

SRAM/NOR-Flash write timing registers 1

Offset: 0x104, reset: 0x0FFFFFFF, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACCMOD
rw 		DATLAT
rw 		CLKDIV
rw 		BUSTURN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATAST
rw 		ADDHLD
rw 		ADDSET
rw
Toggle Fields.

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: Bus turnaround phase duration.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BWTR2

SRAM/NOR-Flash write timing registers 2

Offset: 0x10C, reset: 0x0FFFFFFF, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACCMOD
rw 		DATLAT
rw 		CLKDIV
rw 		BUSTURN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATAST
rw 		ADDHLD
rw 		ADDSET
rw
Toggle Fields.

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: Bus turnaround phase duration.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BWTR3

SRAM/NOR-Flash write timing registers 3

Offset: 0x114, reset: 0x0FFFFFFF, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACCMOD
rw 		DATLAT
rw 		CLKDIV
rw 		BUSTURN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATAST
rw 		ADDHLD
rw 		ADDSET
rw
Toggle Fields.

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: Bus turnaround phase duration.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BWTR4

SRAM/NOR-Flash write timing registers 4

Offset: 0x11C, reset: 0x0FFFFFFF, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACCMOD
rw 		DATLAT
rw 		CLKDIV
rw 		BUSTURN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DATAST
rw 		ADDHLD
rw 		ADDSET
rw
Toggle Fields.

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: Bus turnaround phase duration.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

FPU

0xE000EF34: Floting point unit

0/24 fields covered. Toggle Registers.

FPCCR

Floating-point context control register

Offset: 0x0, reset: 0x00000000, access: read-write

0/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ASPEN
rw 		LSPEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MONRDY
rw 		BFRDY
rw 		MMRDY
rw 		HFRDY
rw 		THREAD
rw 		USER
rw 		LSPACT
rw
Toggle Fields.

LSPACT

Bit 0: LSPACT.

USER

Bit 1: USER.

THREAD

Bit 3: THREAD.

HFRDY

Bit 4: HFRDY.

MMRDY

Bit 5: MMRDY.

BFRDY

Bit 6: BFRDY.

MONRDY

Bit 8: MONRDY.

LSPEN

Bit 30: LSPEN.

ASPEN

Bit 31: ASPEN.

FPCAR

Floating-point context address register

Offset: 0x4, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADDRESS
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ADDRESS
rw
Toggle Fields.

ADDRESS

Bits 3-31: Location of unpopulated floating-point.

FPSCR

Floating-point status control register

Offset: 0x8, reset: 0x00000000, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
N
rw 		Z
rw 		C
rw 		V
rw 		AHP
rw 		DN
rw 		FZ
rw 		RMode
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDC
rw 		IXC
rw 		UFC
rw 		OFC
rw 		DZC
rw 		IOC
rw
Toggle Fields.

IOC

Bit 0: Invalid operation cumulative exception bit.

DZC

Bit 1: Division by zero cumulative exception bit..

OFC

Bit 2: Overflow cumulative exception bit.

UFC

Bit 3: Underflow cumulative exception bit.

IXC

Bit 4: Inexact cumulative exception bit.

IDC

Bit 7: Input denormal cumulative exception bit..

RMode

Bits 22-23: Rounding Mode control field.

FZ

Bit 24: Flush-to-zero mode control bit:.

DN

Bit 25: Default NaN mode control bit.

AHP

Bit 26: Alternative half-precision control bit.

V

Bit 28: Overflow condition code flag.

C

Bit 29: Carry condition code flag.

Z

Bit 30: Zero condition code flag.

N

Bit 31: Negative condition code flag.

FPU_CPACR

0xE000ED88: Floating point unit CPACR

0/1 fields covered. Toggle Registers.

CPACR

Coprocessor access control register

Offset: 0x0, reset: 0x0000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CP
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Toggle Fields.

CP

Bits 20-23: CP.

GPIOA

0x48000000: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0xa8000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MODER15
rw 		MODER14
rw 		MODER13
rw 		MODER12
rw 		MODER11
rw 		MODER10
rw 		MODER9
rw 		MODER8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MODER7
rw 		MODER6
rw 		MODER5
rw 		MODER4
rw 		MODER3
rw 		MODER2
rw 		MODER1
rw 		MODER0
rw
Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OT15
rw 		OT14
rw 		OT13
rw 		OT12
rw 		OT11
rw 		OT10
rw 		OT9
rw 		OT8
rw 		OT7
rw 		OT6
rw 		OT5
rw 		OT4
rw 		OT3
rw 		OT2
rw 		OT1
rw 		OT0
rw
Toggle Fields.

OT0

Bit 0: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x0C000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OSPEEDR15
rw 		OSPEEDR14
rw 		OSPEEDR13
rw 		OSPEEDR12
rw 		OSPEEDR11
rw 		OSPEEDR10
rw 		OSPEEDR9
rw 		OSPEEDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OSPEEDR7
rw 		OSPEEDR6
rw 		OSPEEDR5
rw 		OSPEEDR4
rw 		OSPEEDR3
rw 		OSPEEDR2
rw 		OSPEEDR1
rw 		OSPEEDR0
rw
Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x64000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PUPDR15
rw 		PUPDR14
rw 		PUPDR13
rw 		PUPDR12
rw 		PUPDR11
rw 		PUPDR10
rw 		PUPDR9
rw 		PUPDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PUPDR7
rw 		PUPDR6
rw 		PUPDR5
rw 		PUPDR4
rw 		PUPDR3
rw 		PUPDR2
rw 		PUPDR1
rw 		PUPDR0
rw
Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR15
r 		IDR14
r 		IDR13
r 		IDR12
r 		IDR11
r 		IDR10
r 		IDR9
r 		IDR8
r 		IDR7
r 		IDR6
r 		IDR5
r 		IDR4
r 		IDR3
r 		IDR2
r 		IDR1
r 		IDR0
r
Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ODR15
rw 		ODR14
rw 		ODR13
rw 		ODR12
rw 		ODR11
rw 		ODR10
rw 		ODR9
rw 		ODR8
rw 		ODR7
rw 		ODR6
rw 		ODR5
rw 		ODR4
rw 		ODR3
rw 		ODR2
rw 		ODR1
rw 		ODR0
rw
Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BS15
w 		BS14
w 		BS13
w 		BS12
w 		BS11
w 		BS10
w 		BS9
w 		BS8
w 		BS7
w 		BS6
w 		BS5
w 		BS4
w 		BS3
w 		BS2
w 		BS1
w 		BS0
w
Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LCKK
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LCK15
rw 		LCK14
rw 		LCK13
rw 		LCK12
rw 		LCK11
rw 		LCK10
rw 		LCK9
rw 		LCK8
rw 		LCK7
rw 		LCK6
rw 		LCK5
rw 		LCK4
rw 		LCK3
rw 		LCK2
rw 		LCK1
rw 		LCK0
rw
Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRL7
rw 		AFRL6
rw 		AFRL5
rw 		AFRL4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRL3
rw 		AFRL2
rw 		AFRL1
rw 		AFRL0
rw
Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRH15
rw 		AFRH14
rw 		AFRH13
rw 		AFRH12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRH11
rw 		AFRH10
rw 		AFRH9
rw 		AFRH8
rw
Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOB

0x48000400: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000280, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MODER15
rw 		MODER14
rw 		MODER13
rw 		MODER12
rw 		MODER11
rw 		MODER10
rw 		MODER9
rw 		MODER8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MODER7
rw 		MODER6
rw 		MODER5
rw 		MODER4
rw 		MODER3
rw 		MODER2
rw 		MODER1
rw 		MODER0
rw
Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OT15
rw 		OT14
rw 		OT13
rw 		OT12
rw 		OT11
rw 		OT10
rw 		OT9
rw 		OT8
rw 		OT7
rw 		OT6
rw 		OT5
rw 		OT4
rw 		OT3
rw 		OT2
rw 		OT1
rw 		OT0
rw
Toggle Fields.

OT0

Bit 0: Port x configuration bit 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bit 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bit 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bit 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bit 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bit 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bit 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bit 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bit 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bit 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bit 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bit 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bit 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bit 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bit 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bit 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x000000C0, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OSPEEDR15
rw 		OSPEEDR14
rw 		OSPEEDR13
rw 		OSPEEDR12
rw 		OSPEEDR11
rw 		OSPEEDR10
rw 		OSPEEDR9
rw 		OSPEEDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OSPEEDR7
rw 		OSPEEDR6
rw 		OSPEEDR5
rw 		OSPEEDR4
rw 		OSPEEDR3
rw 		OSPEEDR2
rw 		OSPEEDR1
rw 		OSPEEDR0
rw
Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000100, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PUPDR15
rw 		PUPDR14
rw 		PUPDR13
rw 		PUPDR12
rw 		PUPDR11
rw 		PUPDR10
rw 		PUPDR9
rw 		PUPDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PUPDR7
rw 		PUPDR6
rw 		PUPDR5
rw 		PUPDR4
rw 		PUPDR3
rw 		PUPDR2
rw 		PUPDR1
rw 		PUPDR0
rw
Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR15
r 		IDR14
r 		IDR13
r 		IDR12
r 		IDR11
r 		IDR10
r 		IDR9
r 		IDR8
r 		IDR7
r 		IDR6
r 		IDR5
r 		IDR4
r 		IDR3
r 		IDR2
r 		IDR1
r 		IDR0
r
Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ODR15
rw 		ODR14
rw 		ODR13
rw 		ODR12
rw 		ODR11
rw 		ODR10
rw 		ODR9
rw 		ODR8
rw 		ODR7
rw 		ODR6
rw 		ODR5
rw 		ODR4
rw 		ODR3
rw 		ODR2
rw 		ODR1
rw 		ODR0
rw
Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BS15
w 		BS14
w 		BS13
w 		BS12
w 		BS11
w 		BS10
w 		BS9
w 		BS8
w 		BS7
w 		BS6
w 		BS5
w 		BS4
w 		BS3
w 		BS2
w 		BS1
w 		BS0
w
Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LCKK
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LCK15
rw 		LCK14
rw 		LCK13
rw 		LCK12
rw 		LCK11
rw 		LCK10
rw 		LCK9
rw 		LCK8
rw 		LCK7
rw 		LCK6
rw 		LCK5
rw 		LCK4
rw 		LCK3
rw 		LCK2
rw 		LCK1
rw 		LCK0
rw
Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRL7
rw 		AFRL6
rw 		AFRL5
rw 		AFRL4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRL3
rw 		AFRL2
rw 		AFRL1
rw 		AFRL0
rw
Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRH15
rw 		AFRH14
rw 		AFRH13
rw 		AFRH12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRH11
rw 		AFRH10
rw 		AFRH9
rw 		AFRH8
rw
Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOC

0x48000800: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MODER15
rw 		MODER14
rw 		MODER13
rw 		MODER12
rw 		MODER11
rw 		MODER10
rw 		MODER9
rw 		MODER8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MODER7
rw 		MODER6
rw 		MODER5
rw 		MODER4
rw 		MODER3
rw 		MODER2
rw 		MODER1
rw 		MODER0
rw
Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OT15
rw 		OT14
rw 		OT13
rw 		OT12
rw 		OT11
rw 		OT10
rw 		OT9
rw 		OT8
rw 		OT7
rw 		OT6
rw 		OT5
rw 		OT4
rw 		OT3
rw 		OT2
rw 		OT1
rw 		OT0
rw
Toggle Fields.

OT0

Bit 0: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OSPEEDR15
rw 		OSPEEDR14
rw 		OSPEEDR13
rw 		OSPEEDR12
rw 		OSPEEDR11
rw 		OSPEEDR10
rw 		OSPEEDR9
rw 		OSPEEDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OSPEEDR7
rw 		OSPEEDR6
rw 		OSPEEDR5
rw 		OSPEEDR4
rw 		OSPEEDR3
rw 		OSPEEDR2
rw 		OSPEEDR1
rw 		OSPEEDR0
rw
Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PUPDR15
rw 		PUPDR14
rw 		PUPDR13
rw 		PUPDR12
rw 		PUPDR11
rw 		PUPDR10
rw 		PUPDR9
rw 		PUPDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PUPDR7
rw 		PUPDR6
rw 		PUPDR5
rw 		PUPDR4
rw 		PUPDR3
rw 		PUPDR2
rw 		PUPDR1
rw 		PUPDR0
rw
Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR15
r 		IDR14
r 		IDR13
r 		IDR12
r 		IDR11
r 		IDR10
r 		IDR9
r 		IDR8
r 		IDR7
r 		IDR6
r 		IDR5
r 		IDR4
r 		IDR3
r 		IDR2
r 		IDR1
r 		IDR0
r
Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ODR15
rw 		ODR14
rw 		ODR13
rw 		ODR12
rw 		ODR11
rw 		ODR10
rw 		ODR9
rw 		ODR8
rw 		ODR7
rw 		ODR6
rw 		ODR5
rw 		ODR4
rw 		ODR3
rw 		ODR2
rw 		ODR1
rw 		ODR0
rw
Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BS15
w 		BS14
w 		BS13
w 		BS12
w 		BS11
w 		BS10
w 		BS9
w 		BS8
w 		BS7
w 		BS6
w 		BS5
w 		BS4
w 		BS3
w 		BS2
w 		BS1
w 		BS0
w
Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LCKK
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LCK15
rw 		LCK14
rw 		LCK13
rw 		LCK12
rw 		LCK11
rw 		LCK10
rw 		LCK9
rw 		LCK8
rw 		LCK7
rw 		LCK6
rw 		LCK5
rw 		LCK4
rw 		LCK3
rw 		LCK2
rw 		LCK1
rw 		LCK0
rw
Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRL7
rw 		AFRL6
rw 		AFRL5
rw 		AFRL4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRL3
rw 		AFRL2
rw 		AFRL1
rw 		AFRL0
rw
Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRH15
rw 		AFRH14
rw 		AFRH13
rw 		AFRH12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRH11
rw 		AFRH10
rw 		AFRH9
rw 		AFRH8
rw
Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOD

0x48000C00: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MODER15
rw 		MODER14
rw 		MODER13
rw 		MODER12
rw 		MODER11
rw 		MODER10
rw 		MODER9
rw 		MODER8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MODER7
rw 		MODER6
rw 		MODER5
rw 		MODER4
rw 		MODER3
rw 		MODER2
rw 		MODER1
rw 		MODER0
rw
Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OT15
rw 		OT14
rw 		OT13
rw 		OT12
rw 		OT11
rw 		OT10
rw 		OT9
rw 		OT8
rw 		OT7
rw 		OT6
rw 		OT5
rw 		OT4
rw 		OT3
rw 		OT2
rw 		OT1
rw 		OT0
rw
Toggle Fields.

OT0

Bit 0: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OSPEEDR15
rw 		OSPEEDR14
rw 		OSPEEDR13
rw 		OSPEEDR12
rw 		OSPEEDR11
rw 		OSPEEDR10
rw 		OSPEEDR9
rw 		OSPEEDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OSPEEDR7
rw 		OSPEEDR6
rw 		OSPEEDR5
rw 		OSPEEDR4
rw 		OSPEEDR3
rw 		OSPEEDR2
rw 		OSPEEDR1
rw 		OSPEEDR0
rw
Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PUPDR15
rw 		PUPDR14
rw 		PUPDR13
rw 		PUPDR12
rw 		PUPDR11
rw 		PUPDR10
rw 		PUPDR9
rw 		PUPDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PUPDR7
rw 		PUPDR6
rw 		PUPDR5
rw 		PUPDR4
rw 		PUPDR3
rw 		PUPDR2
rw 		PUPDR1
rw 		PUPDR0
rw
Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR15
r 		IDR14
r 		IDR13
r 		IDR12
r 		IDR11
r 		IDR10
r 		IDR9
r 		IDR8
r 		IDR7
r 		IDR6
r 		IDR5
r 		IDR4
r 		IDR3
r 		IDR2
r 		IDR1
r 		IDR0
r
Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ODR15
rw 		ODR14
rw 		ODR13
rw 		ODR12
rw 		ODR11
rw 		ODR10
rw 		ODR9
rw 		ODR8
rw 		ODR7
rw 		ODR6
rw 		ODR5
rw 		ODR4
rw 		ODR3
rw 		ODR2
rw 		ODR1
rw 		ODR0
rw
Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BS15
w 		BS14
w 		BS13
w 		BS12
w 		BS11
w 		BS10
w 		BS9
w 		BS8
w 		BS7
w 		BS6
w 		BS5
w 		BS4
w 		BS3
w 		BS2
w 		BS1
w 		BS0
w
Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LCKK
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LCK15
rw 		LCK14
rw 		LCK13
rw 		LCK12
rw 		LCK11
rw 		LCK10
rw 		LCK9
rw 		LCK8
rw 		LCK7
rw 		LCK6
rw 		LCK5
rw 		LCK4
rw 		LCK3
rw 		LCK2
rw 		LCK1
rw 		LCK0
rw
Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRL7
rw 		AFRL6
rw 		AFRL5
rw 		AFRL4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRL3
rw 		AFRL2
rw 		AFRL1
rw 		AFRL0
rw
Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRH15
rw 		AFRH14
rw 		AFRH13
rw 		AFRH12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRH11
rw 		AFRH10
rw 		AFRH9
rw 		AFRH8
rw
Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOE

0x48001000: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MODER15
rw 		MODER14
rw 		MODER13
rw 		MODER12
rw 		MODER11
rw 		MODER10
rw 		MODER9
rw 		MODER8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MODER7
rw 		MODER6
rw 		MODER5
rw 		MODER4
rw 		MODER3
rw 		MODER2
rw 		MODER1
rw 		MODER0
rw
Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OT15
rw 		OT14
rw 		OT13
rw 		OT12
rw 		OT11
rw 		OT10
rw 		OT9
rw 		OT8
rw 		OT7
rw 		OT6
rw 		OT5
rw 		OT4
rw 		OT3
rw 		OT2
rw 		OT1
rw 		OT0
rw
Toggle Fields.

OT0

Bit 0: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OSPEEDR15
rw 		OSPEEDR14
rw 		OSPEEDR13
rw 		OSPEEDR12
rw 		OSPEEDR11
rw 		OSPEEDR10
rw 		OSPEEDR9
rw 		OSPEEDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OSPEEDR7
rw 		OSPEEDR6
rw 		OSPEEDR5
rw 		OSPEEDR4
rw 		OSPEEDR3
rw 		OSPEEDR2
rw 		OSPEEDR1
rw 		OSPEEDR0
rw
Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PUPDR15
rw 		PUPDR14
rw 		PUPDR13
rw 		PUPDR12
rw 		PUPDR11
rw 		PUPDR10
rw 		PUPDR9
rw 		PUPDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PUPDR7
rw 		PUPDR6
rw 		PUPDR5
rw 		PUPDR4
rw 		PUPDR3
rw 		PUPDR2
rw 		PUPDR1
rw 		PUPDR0
rw
Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR15
r 		IDR14
r 		IDR13
r 		IDR12
r 		IDR11
r 		IDR10
r 		IDR9
r 		IDR8
r 		IDR7
r 		IDR6
r 		IDR5
r 		IDR4
r 		IDR3
r 		IDR2
r 		IDR1
r 		IDR0
r
Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ODR15
rw 		ODR14
rw 		ODR13
rw 		ODR12
rw 		ODR11
rw 		ODR10
rw 		ODR9
rw 		ODR8
rw 		ODR7
rw 		ODR6
rw 		ODR5
rw 		ODR4
rw 		ODR3
rw 		ODR2
rw 		ODR1
rw 		ODR0
rw
Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BS15
w 		BS14
w 		BS13
w 		BS12
w 		BS11
w 		BS10
w 		BS9
w 		BS8
w 		BS7
w 		BS6
w 		BS5
w 		BS4
w 		BS3
w 		BS2
w 		BS1
w 		BS0
w
Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LCKK
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LCK15
rw 		LCK14
rw 		LCK13
rw 		LCK12
rw 		LCK11
rw 		LCK10
rw 		LCK9
rw 		LCK8
rw 		LCK7
rw 		LCK6
rw 		LCK5
rw 		LCK4
rw 		LCK3
rw 		LCK2
rw 		LCK1
rw 		LCK0
rw
Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRL7
rw 		AFRL6
rw 		AFRL5
rw 		AFRL4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRL3
rw 		AFRL2
rw 		AFRL1
rw 		AFRL0
rw
Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRH15
rw 		AFRH14
rw 		AFRH13
rw 		AFRH12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRH11
rw 		AFRH10
rw 		AFRH9
rw 		AFRH8
rw
Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOF

0x48001400: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MODER15
rw 		MODER14
rw 		MODER13
rw 		MODER12
rw 		MODER11
rw 		MODER10
rw 		MODER9
rw 		MODER8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MODER7
rw 		MODER6
rw 		MODER5
rw 		MODER4
rw 		MODER3
rw 		MODER2
rw 		MODER1
rw 		MODER0
rw
Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OT15
rw 		OT14
rw 		OT13
rw 		OT12
rw 		OT11
rw 		OT10
rw 		OT9
rw 		OT8
rw 		OT7
rw 		OT6
rw 		OT5
rw 		OT4
rw 		OT3
rw 		OT2
rw 		OT1
rw 		OT0
rw
Toggle Fields.

OT0

Bit 0: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OSPEEDR15
rw 		OSPEEDR14
rw 		OSPEEDR13
rw 		OSPEEDR12
rw 		OSPEEDR11
rw 		OSPEEDR10
rw 		OSPEEDR9
rw 		OSPEEDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OSPEEDR7
rw 		OSPEEDR6
rw 		OSPEEDR5
rw 		OSPEEDR4
rw 		OSPEEDR3
rw 		OSPEEDR2
rw 		OSPEEDR1
rw 		OSPEEDR0
rw
Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PUPDR15
rw 		PUPDR14
rw 		PUPDR13
rw 		PUPDR12
rw 		PUPDR11
rw 		PUPDR10
rw 		PUPDR9
rw 		PUPDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PUPDR7
rw 		PUPDR6
rw 		PUPDR5
rw 		PUPDR4
rw 		PUPDR3
rw 		PUPDR2
rw 		PUPDR1
rw 		PUPDR0
rw
Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR15
r 		IDR14
r 		IDR13
r 		IDR12
r 		IDR11
r 		IDR10
r 		IDR9
r 		IDR8
r 		IDR7
r 		IDR6
r 		IDR5
r 		IDR4
r 		IDR3
r 		IDR2
r 		IDR1
r 		IDR0
r
Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ODR15
rw 		ODR14
rw 		ODR13
rw 		ODR12
rw 		ODR11
rw 		ODR10
rw 		ODR9
rw 		ODR8
rw 		ODR7
rw 		ODR6
rw 		ODR5
rw 		ODR4
rw 		ODR3
rw 		ODR2
rw 		ODR1
rw 		ODR0
rw
Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BS15
w 		BS14
w 		BS13
w 		BS12
w 		BS11
w 		BS10
w 		BS9
w 		BS8
w 		BS7
w 		BS6
w 		BS5
w 		BS4
w 		BS3
w 		BS2
w 		BS1
w 		BS0
w
Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LCKK
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LCK15
rw 		LCK14
rw 		LCK13
rw 		LCK12
rw 		LCK11
rw 		LCK10
rw 		LCK9
rw 		LCK8
rw 		LCK7
rw 		LCK6
rw 		LCK5
rw 		LCK4
rw 		LCK3
rw 		LCK2
rw 		LCK1
rw 		LCK0
rw
Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRL7
rw 		AFRL6
rw 		AFRL5
rw 		AFRL4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRL3
rw 		AFRL2
rw 		AFRL1
rw 		AFRL0
rw
Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRH15
rw 		AFRH14
rw 		AFRH13
rw 		AFRH12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRH11
rw 		AFRH10
rw 		AFRH9
rw 		AFRH8
rw
Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOG

0x48001800: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MODER15
rw 		MODER14
rw 		MODER13
rw 		MODER12
rw 		MODER11
rw 		MODER10
rw 		MODER9
rw 		MODER8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MODER7
rw 		MODER6
rw 		MODER5
rw 		MODER4
rw 		MODER3
rw 		MODER2
rw 		MODER1
rw 		MODER0
rw
Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OT15
rw 		OT14
rw 		OT13
rw 		OT12
rw 		OT11
rw 		OT10
rw 		OT9
rw 		OT8
rw 		OT7
rw 		OT6
rw 		OT5
rw 		OT4
rw 		OT3
rw 		OT2
rw 		OT1
rw 		OT0
rw
Toggle Fields.

OT0

Bit 0: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OSPEEDR15
rw 		OSPEEDR14
rw 		OSPEEDR13
rw 		OSPEEDR12
rw 		OSPEEDR11
rw 		OSPEEDR10
rw 		OSPEEDR9
rw 		OSPEEDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OSPEEDR7
rw 		OSPEEDR6
rw 		OSPEEDR5
rw 		OSPEEDR4
rw 		OSPEEDR3
rw 		OSPEEDR2
rw 		OSPEEDR1
rw 		OSPEEDR0
rw
Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PUPDR15
rw 		PUPDR14
rw 		PUPDR13
rw 		PUPDR12
rw 		PUPDR11
rw 		PUPDR10
rw 		PUPDR9
rw 		PUPDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PUPDR7
rw 		PUPDR6
rw 		PUPDR5
rw 		PUPDR4
rw 		PUPDR3
rw 		PUPDR2
rw 		PUPDR1
rw 		PUPDR0
rw
Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR15
r 		IDR14
r 		IDR13
r 		IDR12
r 		IDR11
r 		IDR10
r 		IDR9
r 		IDR8
r 		IDR7
r 		IDR6
r 		IDR5
r 		IDR4
r 		IDR3
r 		IDR2
r 		IDR1
r 		IDR0
r
Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ODR15
rw 		ODR14
rw 		ODR13
rw 		ODR12
rw 		ODR11
rw 		ODR10
rw 		ODR9
rw 		ODR8
rw 		ODR7
rw 		ODR6
rw 		ODR5
rw 		ODR4
rw 		ODR3
rw 		ODR2
rw 		ODR1
rw 		ODR0
rw
Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BS15
w 		BS14
w 		BS13
w 		BS12
w 		BS11
w 		BS10
w 		BS9
w 		BS8
w 		BS7
w 		BS6
w 		BS5
w 		BS4
w 		BS3
w 		BS2
w 		BS1
w 		BS0
w
Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LCKK
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LCK15
rw 		LCK14
rw 		LCK13
rw 		LCK12
rw 		LCK11
rw 		LCK10
rw 		LCK9
rw 		LCK8
rw 		LCK7
rw 		LCK6
rw 		LCK5
rw 		LCK4
rw 		LCK3
rw 		LCK2
rw 		LCK1
rw 		LCK0
rw
Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRL7
rw 		AFRL6
rw 		AFRL5
rw 		AFRL4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRL3
rw 		AFRL2
rw 		AFRL1
rw 		AFRL0
rw
Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRH15
rw 		AFRH14
rw 		AFRH13
rw 		AFRH12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRH11
rw 		AFRH10
rw 		AFRH9
rw 		AFRH8
rw
Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOH

0x48001C00: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MODER15
rw 		MODER14
rw 		MODER13
rw 		MODER12
rw 		MODER11
rw 		MODER10
rw 		MODER9
rw 		MODER8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MODER7
rw 		MODER6
rw 		MODER5
rw 		MODER4
rw 		MODER3
rw 		MODER2
rw 		MODER1
rw 		MODER0
rw
Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OT15
rw 		OT14
rw 		OT13
rw 		OT12
rw 		OT11
rw 		OT10
rw 		OT9
rw 		OT8
rw 		OT7
rw 		OT6
rw 		OT5
rw 		OT4
rw 		OT3
rw 		OT2
rw 		OT1
rw 		OT0
rw
Toggle Fields.

OT0

Bit 0: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OSPEEDR15
rw 		OSPEEDR14
rw 		OSPEEDR13
rw 		OSPEEDR12
rw 		OSPEEDR11
rw 		OSPEEDR10
rw 		OSPEEDR9
rw 		OSPEEDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OSPEEDR7
rw 		OSPEEDR6
rw 		OSPEEDR5
rw 		OSPEEDR4
rw 		OSPEEDR3
rw 		OSPEEDR2
rw 		OSPEEDR1
rw 		OSPEEDR0
rw
Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PUPDR15
rw 		PUPDR14
rw 		PUPDR13
rw 		PUPDR12
rw 		PUPDR11
rw 		PUPDR10
rw 		PUPDR9
rw 		PUPDR8
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PUPDR7
rw 		PUPDR6
rw 		PUPDR5
rw 		PUPDR4
rw 		PUPDR3
rw 		PUPDR2
rw 		PUPDR1
rw 		PUPDR0
rw
Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IDR15
r 		IDR14
r 		IDR13
r 		IDR12
r 		IDR11
r 		IDR10
r 		IDR9
r 		IDR8
r 		IDR7
r 		IDR6
r 		IDR5
r 		IDR4
r 		IDR3
r 		IDR2
r 		IDR1
r 		IDR0
r
Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ODR15
rw 		ODR14
rw 		ODR13
rw 		ODR12
rw 		ODR11
rw 		ODR10
rw 		ODR9
rw 		ODR8
rw 		ODR7
rw 		ODR6
rw 		ODR5
rw 		ODR4
rw 		ODR3
rw 		ODR2
rw 		ODR1
rw 		ODR0
rw
Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BS15
w 		BS14
w 		BS13
w 		BS12
w 		BS11
w 		BS10
w 		BS9
w 		BS8
w 		BS7
w 		BS6
w 		BS5
w 		BS4
w 		BS3
w 		BS2
w 		BS1
w 		BS0
w
Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LCKK
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LCK15
rw 		LCK14
rw 		LCK13
rw 		LCK12
rw 		LCK11
rw 		LCK10
rw 		LCK9
rw 		LCK8
rw 		LCK7
rw 		LCK6
rw 		LCK5
rw 		LCK4
rw 		LCK3
rw 		LCK2
rw 		LCK1
rw 		LCK0
rw
Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRL7
rw 		AFRL6
rw 		AFRL5
rw 		AFRL4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRL3
rw 		AFRL2
rw 		AFRL1
rw 		AFRL0
rw
Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
AFRH15
rw 		AFRH14
rw 		AFRH13
rw 		AFRH12
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
AFRH11
rw 		AFRH10
rw 		AFRH9
rw 		AFRH8
rw
Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BR15
w 		BR14
w 		BR13
w 		BR12
w 		BR11
w 		BR10
w 		BR9
w 		BR8
w 		BR7
w 		BR6
w 		BR5
w 		BR4
w 		BR3
w 		BR2
w 		BR1
w 		BR0
w
Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

I2C1

0x40005400: Inter-integrated circuit

76/77 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x00000000, access: Unspecified

20/21 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PECEN
rw 		ALERTEN
rw 		SMBDEN
rw 		SMBHEN
rw 		GCEN
rw 		WUPEN
rw 		NOSTRETCH
rw 		SBC
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXDMAEN
rw 		TXDMAEN
rw 		SWRST
w 		ANFOFF
rw 		DNF
rw 		ERRIE
rw 		TCIE
rw 		STOPIE
rw 		NACKIE
rw 		ADDRIE
rw 		RXIE
rw 		TXIE
rw 		PE
rw
Toggle Fields.

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

SWRST

Bit 13: Software reset.

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PECBYTE
rw 		AUTOEND
rw 		RELOAD
rw 		NBYTES
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
NACK
rw 		STOP
rw 		START
rw 		HEAD10R
rw 		ADD10
rw 		RD_WRN
rw 		SADD
rw
Toggle Fields.

SADD

Bits 0-9: Slave address bit 9:8 (master mode).

Allowed values: 0-1023

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0-255

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompeted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OA1EN
rw 		OA1MODE
rw 		OA1
rw
Toggle Fields.

OA1

Bits 0-9: Interface address.

Allowed values: 0-1023

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xC, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OA2EN
rw 		OA2MSK
rw 		OA2
rw
Toggle Fields.

OA2

Bits 1-7: Interface address.

Allowed values: 0-127

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PRESC
rw 		SCLDEL
rw 		SDADEL
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SCLH
rw 		SCLL
rw
Toggle Fields.

SCLL

Bits 0-7: SCL low period (master mode).

Allowed values: 0-255

SCLH

Bits 8-15: SCL high period (master mode).

Allowed values: 0-255

SDADEL

Bits 16-19: Data hold time.

Allowed values: 0-15

SCLDEL

Bits 20-23: Data setup time.

Allowed values: 0-15

PRESC

Bits 28-31: Timing prescaler.

Allowed values: 0-15

TIMEOUTR

Status register 1

Offset: 0x14, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TEXTEN
rw 		TIMEOUTB
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TIMOUTEN
rw 		TIDLE
rw 		TIMEOUTA
rw
Toggle Fields.

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0-4095

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0-4095

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADDCODE
r 		DIR
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BUSY
r 		ALERT
r 		TIMEOUT
r 		PECERR
r 		OVR
r 		ARLO
r 		BERR
r 		TCR
r 		TC
r 		STOPF
r 		NACKF
r 		ADDR
r 		RXNE
r 		TXIS
rw 		TXE
rw
Toggle Fields.

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0-127

ICR

Interrupt clear register

Offset: 0x1C, reset: 0x00000000, access: write-only

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ALERTCF
w 		TIMOUTCF
w 		PECCF
w 		OVRCF
w 		ARLOCF
w 		BERRCF
w 		STOPCF
w 		NACKCF
w 		ADDRCF
w
Toggle Fields.

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PEC
r
Toggle Fields.

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0-255

RXDR

Receive data register

Offset: 0x24, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXDATA
r
Toggle Fields.

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0-255

TXDR

Transmit data register

Offset: 0x28, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TXDATA
rw
Toggle Fields.

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0-255

I2C2

0x40005800: Inter-integrated circuit

76/77 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x00000000, access: Unspecified

20/21 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PECEN
rw 		ALERTEN
rw 		SMBDEN
rw 		SMBHEN
rw 		GCEN
rw 		WUPEN
rw 		NOSTRETCH
rw 		SBC
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXDMAEN
rw 		TXDMAEN
rw 		SWRST
w 		ANFOFF
rw 		DNF
rw 		ERRIE
rw 		TCIE
rw 		STOPIE
rw 		NACKIE
rw 		ADDRIE
rw 		RXIE
rw 		TXIE
rw 		PE
rw
Toggle Fields.

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

SWRST

Bit 13: Software reset.

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PECBYTE
rw 		AUTOEND
rw 		RELOAD
rw 		NBYTES
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
NACK
rw 		STOP
rw 		START
rw 		HEAD10R
rw 		ADD10
rw 		RD_WRN
rw 		SADD
rw
Toggle Fields.

SADD

Bits 0-9: Slave address bit 9:8 (master mode).

Allowed values: 0-1023

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0-255

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompeted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OA1EN
rw 		OA1MODE
rw 		OA1
rw
Toggle Fields.

OA1

Bits 0-9: Interface address.

Allowed values: 0-1023

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xC, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OA2EN
rw 		OA2MSK
rw 		OA2
rw
Toggle Fields.

OA2

Bits 1-7: Interface address.

Allowed values: 0-127

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PRESC
rw 		SCLDEL
rw 		SDADEL
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SCLH
rw 		SCLL
rw
Toggle Fields.

SCLL

Bits 0-7: SCL low period (master mode).

Allowed values: 0-255

SCLH

Bits 8-15: SCL high period (master mode).

Allowed values: 0-255

SDADEL

Bits 16-19: Data hold time.

Allowed values: 0-15

SCLDEL

Bits 20-23: Data setup time.

Allowed values: 0-15

PRESC

Bits 28-31: Timing prescaler.

Allowed values: 0-15

TIMEOUTR

Status register 1

Offset: 0x14, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TEXTEN
rw 		TIMEOUTB
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TIMOUTEN
rw 		TIDLE
rw 		TIMEOUTA
rw
Toggle Fields.

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0-4095

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0-4095

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADDCODE
r 		DIR
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BUSY
r 		ALERT
r 		TIMEOUT
r 		PECERR
r 		OVR
r 		ARLO
r 		BERR
r 		TCR
r 		TC
r 		STOPF
r 		NACKF
r 		ADDR
r 		RXNE
r 		TXIS
rw 		TXE
rw
Toggle Fields.

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0-127

ICR

Interrupt clear register

Offset: 0x1C, reset: 0x00000000, access: write-only

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ALERTCF
w 		TIMOUTCF
w 		PECCF
w 		OVRCF
w 		ARLOCF
w 		BERRCF
w 		STOPCF
w 		NACKCF
w 		ADDRCF
w
Toggle Fields.

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PEC
r
Toggle Fields.

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0-255

RXDR

Receive data register

Offset: 0x24, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXDATA
r
Toggle Fields.

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0-255

TXDR

Transmit data register

Offset: 0x28, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TXDATA
rw
Toggle Fields.

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0-255

I2C3

0x40007800: Inter-integrated circuit

76/77 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x00000000, access: Unspecified

20/21 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PECEN
rw 		ALERTEN
rw 		SMBDEN
rw 		SMBHEN
rw 		GCEN
rw 		WUPEN
rw 		NOSTRETCH
rw 		SBC
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXDMAEN
rw 		TXDMAEN
rw 		SWRST
w 		ANFOFF
rw 		DNF
rw 		ERRIE
rw 		TCIE
rw 		STOPIE
rw 		NACKIE
rw 		ADDRIE
rw 		RXIE
rw 		TXIE
rw 		PE
rw
Toggle Fields.

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

SWRST

Bit 13: Software reset.

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PECBYTE
rw 		AUTOEND
rw 		RELOAD
rw 		NBYTES
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
NACK
rw 		STOP
rw 		START
rw 		HEAD10R
rw 		ADD10
rw 		RD_WRN
rw 		SADD
rw
Toggle Fields.

SADD

Bits 0-9: Slave address bit 9:8 (master mode).

Allowed values: 0-1023

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0-255

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompeted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OA1EN
rw 		OA1MODE
rw 		OA1
rw
Toggle Fields.

OA1

Bits 0-9: Interface address.

Allowed values: 0-1023

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xC, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OA2EN
rw 		OA2MSK
rw 		OA2
rw
Toggle Fields.

OA2

Bits 1-7: Interface address.

Allowed values: 0-127

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PRESC
rw 		SCLDEL
rw 		SDADEL
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SCLH
rw 		SCLL
rw
Toggle Fields.

SCLL

Bits 0-7: SCL low period (master mode).

Allowed values: 0-255

SCLH

Bits 8-15: SCL high period (master mode).

Allowed values: 0-255

SDADEL

Bits 16-19: Data hold time.

Allowed values: 0-15

SCLDEL

Bits 20-23: Data setup time.

Allowed values: 0-15

PRESC

Bits 28-31: Timing prescaler.

Allowed values: 0-15

TIMEOUTR

Status register 1

Offset: 0x14, reset: 0x00000000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TEXTEN
rw 		TIMEOUTB
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TIMOUTEN
rw 		TIDLE
rw 		TIMEOUTA
rw
Toggle Fields.

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0-4095

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0-4095

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADDCODE
r 		DIR
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BUSY
r 		ALERT
r 		TIMEOUT
r 		PECERR
r 		OVR
r 		ARLO
r 		BERR
r 		TCR
r 		TC
r 		STOPF
r 		NACKF
r 		ADDR
r 		RXNE
r 		TXIS
rw 		TXE
rw
Toggle Fields.

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0-127

ICR

Interrupt clear register

Offset: 0x1C, reset: 0x00000000, access: write-only

9/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ALERTCF
w 		TIMOUTCF
w 		PECCF
w 		OVRCF
w 		ARLOCF
w 		BERRCF
w 		STOPCF
w 		NACKCF
w 		ADDRCF
w
Toggle Fields.

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PEC
r
Toggle Fields.

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0-255

RXDR

Receive data register

Offset: 0x24, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXDATA
r
Toggle Fields.

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0-255

TXDR

Transmit data register

Offset: 0x28, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TXDATA
rw
Toggle Fields.

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0-255

I2S2ext

0x40003400: Serial peripheral interface/Inter-IC sound

52/52 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BIDIMODE
rw 		BIDIOE
rw 		CRCEN
rw 		CRCNEXT
rw 		CRCL
rw 		RXONLY
rw 		SSM
rw 		SSI
rw 		LSBFIRST
rw 		SPE
rw 		BR
rw 		MSTR
rw 		CPOL
rw 		CPHA
rw
Toggle Fields.

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LDMA_TX
rw 		LDMA_RX
rw 		FRXTH
rw 		DS
rw 		TXEIE
rw 		RXNEIE
rw 		ERRIE
rw 		FRF
rw 		NSSP
rw 		SSOE
rw 		TXDMAEN
rw 		RXDMAEN
rw
Toggle Fields.

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, reset: 0x0002, access: Unspecified

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FTLVL
r 		FRLVL
r 		TIFRFE
r 		BSY
r 		OVR
r 		MODF
r 		CRCERR
rw 		UDR
r 		CHSIDE
r 		TXE
r 		RXNE
r
Toggle Fields.

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

TIFRFE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DR
rw
Toggle Fields.

DR

Bits 0-15: Data register.

Allowed values: 0-65535

CRCPR

CRC polynomial register

Offset: 0x10, reset: 0x0007, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CRCPOLY
rw
Toggle Fields.

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0-65535

RXCRCR

RX CRC register

Offset: 0x14, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RxCRC
r
Toggle Fields.

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0-65535

TXCRCR

TX CRC register

Offset: 0x18, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TxCRC
r
Toggle Fields.

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0-65535

I2SCFGR

I2S configuration register

Offset: 0x1C, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I2SMOD
rw 		I2SE
rw 		I2SCFG
rw 		PCMSYNC
rw 		I2SSTD
rw 		CKPOL
rw 		DATLEN
rw 		CHLEN
rw
Toggle Fields.

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, reset: 0x00000010, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCKOE
rw 		ODD
rw 		I2SDIV
rw
Toggle Fields.

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 2-255

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

I2S3ext

0x40004000: Serial peripheral interface/Inter-IC sound

52/52 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BIDIMODE
rw 		BIDIOE
rw 		CRCEN
rw 		CRCNEXT
rw 		CRCL
rw 		RXONLY
rw 		SSM
rw 		SSI
rw 		LSBFIRST
rw 		SPE
rw 		BR
rw 		MSTR
rw 		CPOL
rw 		CPHA
rw
Toggle Fields.

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LDMA_TX
rw 		LDMA_RX
rw 		FRXTH
rw 		DS
rw 		TXEIE
rw 		RXNEIE
rw 		ERRIE
rw 		FRF
rw 		NSSP
rw 		SSOE
rw 		TXDMAEN
rw 		RXDMAEN
rw
Toggle Fields.

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, reset: 0x0002, access: Unspecified

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FTLVL
r 		FRLVL
r 		TIFRFE
r 		BSY
r 		OVR
r 		MODF
r 		CRCERR
rw 		UDR
r 		CHSIDE
r 		TXE
r 		RXNE
r
Toggle Fields.

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

TIFRFE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DR
rw
Toggle Fields.

DR

Bits 0-15: Data register.

Allowed values: 0-65535

CRCPR

CRC polynomial register

Offset: 0x10, reset: 0x0007, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CRCPOLY
rw
Toggle Fields.

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0-65535

RXCRCR

RX CRC register

Offset: 0x14, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RxCRC
r
Toggle Fields.

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0-65535

TXCRCR

TX CRC register

Offset: 0x18, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TxCRC
r
Toggle Fields.

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0-65535

I2SCFGR

I2S configuration register

Offset: 0x1C, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I2SMOD
rw 		I2SE
rw 		I2SCFG
rw 		PCMSYNC
rw 		I2SSTD
rw 		CKPOL
rw 		DATLEN
rw 		CHLEN
rw
Toggle Fields.

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, reset: 0x00000010, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCKOE
rw 		ODD
rw 		I2SDIV
rw
Toggle Fields.

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 2-255

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

IWDG

0x40003000: Independent watchdog

7/7 fields covered. Toggle Registers.

KR

Key register

Offset: 0x0, reset: 0x00000000, access: write-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
KEY
w
Toggle Fields.

KEY

Bits 0-15: Key value.

Allowed values:
21845: Enable: Enable access to PR, RLR and WINR registers (0x5555)
43690: Reset: Reset the watchdog value (0xAAAA)
52428: Start: Start the watchdog (0xCCCC)

PR

Prescaler register

Offset: 0x4, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PR
rw
Toggle Fields.

PR

Bits 0-2: Prescaler divider.

Allowed values:
0: DivideBy4: Divider /4
1: DivideBy8: Divider /8
2: DivideBy16: Divider /16
3: DivideBy32: Divider /32
4: DivideBy64: Divider /64
5: DivideBy128: Divider /128
6: DivideBy256: Divider /256
7: DivideBy256bis: Divider /256

RLR

Reload register

Offset: 0x8, reset: 0x00000FFF, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RL
rw
Toggle Fields.

RL

Bits 0-11: Watchdog counter reload value.

Allowed values: 0-4095

SR

Status register

Offset: 0xC, reset: 0x00000000, access: read-only

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
WVU
r 		RVU
r 		PVU
r
Toggle Fields.

PVU

Bit 0: Watchdog prescaler value update.

RVU

Bit 1: Watchdog counter reload value update.

WVU

Bit 2: Watchdog counter window value update.

WINR

Window register

Offset: 0x10, reset: 0x00000FFF, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
WIN
rw
Toggle Fields.

WIN

Bits 0-11: Watchdog counter window value.

Allowed values: 0-4095

MPU

0xE000ED90: Memory protection unit

6/19 fields covered. Toggle Registers.

MPU_TYPER

MPU type register

Offset: 0x0, reset: 0X00000800, access: read-only

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IREGION
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DREGION
r 		SEPARATE
r
Toggle Fields.

SEPARATE

Bit 0: Separate flag.

DREGION

Bits 8-15: Number of MPU data regions.

IREGION

Bits 16-23: Number of MPU instruction regions.

MPU_CTRL

MPU control register

Offset: 0x4, reset: 0X00000000, access: read-only

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PRIVDEFENA
r 		HFNMIENA
r 		ENABLE
r
Toggle Fields.

ENABLE

Bit 0: Enables the MPU.

HFNMIENA

Bit 1: Enables the operation of MPU during hard fault.

PRIVDEFENA

Bit 2: Enable priviliged software access to default memory map.

MPU_RNR

MPU region number register

Offset: 0x8, reset: 0X00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
REGION
rw
Toggle Fields.

REGION

Bits 0-7: MPU region.

MPU_RBAR

MPU region base address register

Offset: 0xC, reset: 0X00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADDR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ADDR
rw 		VALID
rw 		REGION
rw
Toggle Fields.

REGION

Bits 0-3: MPU region field.

VALID

Bit 4: MPU region number valid.

ADDR

Bits 5-31: Region base address field.

MPU_RASR

MPU region attribute and size register

Offset: 0x10, reset: 0X00000000, access: read-write

0/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
XN
rw 		AP
rw 		TEX
rw 		S
rw 		C
rw 		B
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SRD
rw 		SIZE
rw 		ENABLE
rw
Toggle Fields.

ENABLE

Bit 0: Region enable bit..

SIZE

Bits 1-5: Size of the MPU protection region.

SRD

Bits 8-15: Subregion disable bits.

B

Bit 16: memory attribute.

C

Bit 17: memory attribute.

S

Bit 18: Shareable memory attribute.

TEX

Bits 19-21: memory attribute.

AP

Bits 24-26: Access permission.

XN

Bit 28: Instruction access disable bit.

NVIC

0xE000E100: Nested Vectored Interrupt Controller

3/99 fields covered. Toggle Registers.

ISER0

Interrupt Set-Enable Register

Offset: 0x0, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SETENA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SETENA
rw
Toggle Fields.

SETENA

Bits 0-31: SETENA.

ISER1

Interrupt Set-Enable Register

Offset: 0x4, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SETENA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SETENA
rw
Toggle Fields.

SETENA

Bits 0-31: SETENA.

ISER2

Interrupt Set-Enable Register

Offset: 0x8, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SETENA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SETENA
rw
Toggle Fields.

SETENA

Bits 0-31: SETENA.

ICER0

Interrupt Clear-Enable Register

Offset: 0x80, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CLRENA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRENA
rw
Toggle Fields.

CLRENA

Bits 0-31: CLRENA.

ICER1

Interrupt Clear-Enable Register

Offset: 0x84, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CLRENA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRENA
rw
Toggle Fields.

CLRENA

Bits 0-31: CLRENA.

ICER2

Interrupt Clear-Enable Register

Offset: 0x88, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CLRENA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRENA
rw
Toggle Fields.

CLRENA

Bits 0-31: CLRENA.

ISPR0

Interrupt Set-Pending Register

Offset: 0x100, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SETPEND
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SETPEND
rw
Toggle Fields.

SETPEND

Bits 0-31: SETPEND.

ISPR1

Interrupt Set-Pending Register

Offset: 0x104, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SETPEND
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SETPEND
rw
Toggle Fields.

SETPEND

Bits 0-31: SETPEND.

ISPR2

Interrupt Set-Pending Register

Offset: 0x108, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SETPEND
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SETPEND
rw
Toggle Fields.

SETPEND

Bits 0-31: SETPEND.

ICPR0

Interrupt Clear-Pending Register

Offset: 0x180, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CLRPEND
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRPEND
rw
Toggle Fields.

CLRPEND

Bits 0-31: CLRPEND.

ICPR1

Interrupt Clear-Pending Register

Offset: 0x184, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CLRPEND
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRPEND
rw
Toggle Fields.

CLRPEND

Bits 0-31: CLRPEND.

ICPR2

Interrupt Clear-Pending Register

Offset: 0x188, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CLRPEND
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRPEND
rw
Toggle Fields.

CLRPEND

Bits 0-31: CLRPEND.

IABR0

Interrupt Active Bit Register

Offset: 0x200, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACTIVE
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ACTIVE
r
Toggle Fields.

ACTIVE

Bits 0-31: ACTIVE.

IABR1

Interrupt Active Bit Register

Offset: 0x204, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACTIVE
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ACTIVE
r
Toggle Fields.

ACTIVE

Bits 0-31: ACTIVE.

IABR2

Interrupt Active Bit Register

Offset: 0x208, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ACTIVE
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ACTIVE
r
Toggle Fields.

ACTIVE

Bits 0-31: ACTIVE.

IPR0

Interrupt Priority Register

Offset: 0x300, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR1

Interrupt Priority Register

Offset: 0x304, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR2

Interrupt Priority Register

Offset: 0x308, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR3

Interrupt Priority Register

Offset: 0x30C, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR4

Interrupt Priority Register

Offset: 0x310, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR5

Interrupt Priority Register

Offset: 0x314, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR6

Interrupt Priority Register

Offset: 0x318, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR7

Interrupt Priority Register

Offset: 0x31C, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR8

Interrupt Priority Register

Offset: 0x320, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR9

Interrupt Priority Register

Offset: 0x324, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR10

Interrupt Priority Register

Offset: 0x328, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR11

Interrupt Priority Register

Offset: 0x32C, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR12

Interrupt Priority Register

Offset: 0x330, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR13

Interrupt Priority Register

Offset: 0x334, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR14

Interrupt Priority Register

Offset: 0x338, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR15

Interrupt Priority Register

Offset: 0x33C, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR16

Interrupt Priority Register

Offset: 0x340, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR17

Interrupt Priority Register

Offset: 0x344, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR18

Interrupt Priority Register

Offset: 0x348, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR19

Interrupt Priority Register

Offset: 0x34C, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR20

Interrupt Priority Register

Offset: 0x350, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IPR_N3
rw 		IPR_N2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IPR_N1
rw 		IPR_N0
rw
Toggle Fields.

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

NVIC_STIR

0xE000EF00: Nested vectored interrupt controller

0/1 fields covered. Toggle Registers.

STIR

Software trigger interrupt register

Offset: 0x0, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
INTID
rw
Toggle Fields.

INTID

Bits 0-8: Software generated interrupt ID.

OPAMP

1073807360: Operational Amplifier

19/64 fields covered. Toggle Registers.

OPAMP1_CSR

OPAMP1 control register

Offset: 0x56, reset: 0, access: Unspecified

1/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LOCK
rw 		OUTCAL
r 		TSTREF
rw 		TRIMOFFSETN
rw 		TRIMOFFSETP
rw 		USER_TRIM
rw 		PGA_GAIN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PGA_GAIN
rw 		CALSEL
rw 		CALON
rw 		VPS_SEL
rw 		VMS_SEL
rw 		TCM_EN
rw 		VM_SEL
rw 		VP_SEL
rw 		FORCE_VP
rw 		OPAMP1EN
rw
Toggle Fields.

OPAMP1EN

Bit 0: OPAMP1 enable.

FORCE_VP

Bit 1: FORCE_VP.

VP_SEL

Bits 2-3: OPAMP Non inverting input selection.

VM_SEL

Bits 5-6: OPAMP inverting input selection.

TCM_EN

Bit 7: Timer controlled Mux mode enable.

VMS_SEL

Bit 8: OPAMP inverting input secondary selection.

VPS_SEL

Bits 9-10: OPAMP Non inverting input secondary selection.

CALON

Bit 11: Calibration mode enable.

CALSEL

Bits 12-13: Calibration selection.

PGA_GAIN

Bits 14-17: Gain in PGA mode.

USER_TRIM

Bit 18: User trimming enable.

TRIMOFFSETP

Bits 19-23: Offset trimming value (PMOS).

TRIMOFFSETN

Bits 24-28: Offset trimming value (NMOS).

TSTREF

Bit 29: TSTREF.

OUTCAL

Bit 30: OPAMP ouput status flag.

LOCK

Bit 31: OPAMP lock.

OPAMP2_CSR

OPAMP2 control register

Offset: 0x60, reset: 0, access: Unspecified

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LOCK
rw 		OUTCAL
r 		TSTREF
rw 		TRIMOFFSETN
rw 		TRIMOFFSETP
rw 		USER_TRIM
rw 		PGA_GAIN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PGA_GAIN
rw 		CALSEL
rw 		CALON
rw 		VPS_SEL
rw 		VMS_SEL
rw 		TCM_EN
rw 		VM_SEL
rw 		VP_SEL
rw 		FORCE_VP
rw 		OPAMP2EN
rw
Toggle Fields.

OPAMP2EN

Bit 0: OPAMP2 enable.

Allowed values:
0: Disabled: OPAMP2 is disabled
1: Enabled: OPAMP2 is enabled

FORCE_VP

Bit 1: FORCE_VP.

Allowed values:
0: Normal: Normal operating mode
1: Calibration: Calibration mode. Non-inverting input connected to calibration reference

VP_SEL

Bits 2-3: OPAMP Non inverting input selection.

Allowed values:
1: PB14: PB14 used as OPAMP2 non-inverting input
2: PB0: PB0 used as OPAMP2 non-inverting input
3: PA7: PA7 used as OPAMP2 non-inverting input

VM_SEL

Bits 5-6: OPAMP inverting input selection.

Allowed values:
0: PC5: PC5 (VM0) used as OPAMP2 inverting input
1: PA5: PA5 (VM1) used as OPAMP2 inverting input
2: PGA: Resistor feedback output (PGA mode)
3: Follower: Follower mode

TCM_EN

Bit 7: Timer controlled Mux mode enable.

Allowed values:
0: Disabled: Timer controlled mux disabled
1: Enabled: Timer controlled mux enabled

VMS_SEL

Bit 8: OPAMP inverting input secondary selection.

Allowed values:
0: PC5: PC5 (VM0) used as OPAMP2 inverting input when TCM_EN=1
1: PA5: PA5 (VM1) used as OPAMP2 inverting input when TCM_EN=1

VPS_SEL

Bits 9-10: OPAMP Non inverting input secondary selection.

Allowed values:
1: PB14: PB14 used as OPAMP2 non-inverting input when TCM_EN=1
2: PB0: PB0 used as OPAMP2 non-inverting input when TCM_EN=1
3: PA7: PA7 used as OPAMP2 non-inverting input when TCM_EN=1

CALON

Bit 11: Calibration mode enable.

Allowed values:
0: Disabled: Calibration mode disabled
1: Enabled: Calibration mode enabled

CALSEL

Bits 12-13: Calibration selection.

Allowed values:
0: Percent3_3: VREFOPAMP=3.3% VDDA
1: Percent10: VREFOPAMP=10% VDDA
2: Percent50: VREFOPAMP=50% VDDA
3: Percent90: VREFOPAMP=90% VDDA

PGA_GAIN

Bits 14-17: Gain in PGA mode.

Allowed values:
0: Gain2: Gain 2
1: Gain4: Gain 4
2: Gain8: Gain 8
4: Gain16: Gain 16
8: Gain2_VM0: Gain 2, feedback connected to VM0
9: Gain4_VM0: Gain 4, feedback connected to VM0
10: Gain8_VM0: Gain 8, feedback connected to VM0
11: Gain16_VM0: Gain 16, feedback connected to VM0
12: Gain2_VM1: Gain 2, feedback connected to VM1
13: Gain4_VM1: Gain 4, feedback connected to VM1
14: Gain8_VM1: Gain 8, feedback connected to VM1
15: Gain16_VM1: Gain 16, feedback connected to VM1

USER_TRIM

Bit 18: User trimming enable.

Allowed values:
0: Disabled: User trimming disabled
1: Enabled: User trimming enabled

TRIMOFFSETP

Bits 19-23: Offset trimming value (PMOS).

Allowed values: 0-31

TRIMOFFSETN

Bits 24-28: Offset trimming value (NMOS).

Allowed values: 0-31

TSTREF

Bit 29: TSTREF.

Allowed values:
0: Output: VREFOPAMP2 is output
1: NotOutput: VREFOPAMP2 is not output

OUTCAL

Bit 30: OPAMP ouput status flag.

Allowed values:
0: Low: Non-inverting < inverting
1: High: Non-inverting > inverting

LOCK

Bit 31: OPAMP lock.

Allowed values:
0: Unlocked: Comparator CSR bits are read-write
1: Locked: Comparator CSR bits are read-only

OPAMP3_CSR

OPAMP3 control register

Offset: 0x64, reset: 0, access: Unspecified

1/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LOCK
rw 		OUTCAL
r 		TSTREF
rw 		TRIMOFFSETN
rw 		TRIMOFFSETP
rw 		USER_TRIM
rw 		PGA_GAIN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PGA_GAIN
rw 		CALSEL
rw 		CALON
rw 		VPS_SEL
rw 		VMS_SEL
rw 		TCM_EN
rw 		VM_SEL
rw 		VP_SEL
rw 		FORCE_VP
rw 		OPAMP3EN
rw
Toggle Fields.

OPAMP3EN

Bit 0: OPAMP3 enable.

FORCE_VP

Bit 1: FORCE_VP.

VP_SEL

Bits 2-3: OPAMP Non inverting input selection.

VM_SEL

Bits 5-6: OPAMP inverting input selection.

TCM_EN

Bit 7: Timer controlled Mux mode enable.

VMS_SEL

Bit 8: OPAMP inverting input secondary selection.

VPS_SEL

Bits 9-10: OPAMP Non inverting input secondary selection.

CALON

Bit 11: Calibration mode enable.

CALSEL

Bits 12-13: Calibration selection.

PGA_GAIN

Bits 14-17: Gain in PGA mode.

USER_TRIM

Bit 18: User trimming enable.

TRIMOFFSETP

Bits 19-23: Offset trimming value (PMOS).

TRIMOFFSETN

Bits 24-28: Offset trimming value (NMOS).

TSTREF

Bit 29: TSTREF.

OUTCAL

Bit 30: OPAMP ouput status flag.

LOCK

Bit 31: OPAMP lock.

OPAMP4_CSR

OPAMP4 control register

Offset: 0x68, reset: 0, access: Unspecified

1/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LOCK
rw 		OUTCAL
r 		TSTREF
rw 		TRIMOFFSETN
rw 		TRIMOFFSETP
rw 		USER_TRIM
rw 		PGA_GAIN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PGA_GAIN
rw 		CALSEL
rw 		CALON
rw 		VPS_SEL
rw 		VMS_SEL
rw 		TCM_EN
rw 		VM_SEL
rw 		VP_SEL
rw 		FORCE_VP
rw 		OPAMP4EN
rw
Toggle Fields.

OPAMP4EN

Bit 0: OPAMP4 enable.

FORCE_VP

Bit 1: FORCE_VP.

VP_SEL

Bits 2-3: OPAMP Non inverting input selection.

VM_SEL

Bits 5-6: OPAMP inverting input selection.

TCM_EN

Bit 7: Timer controlled Mux mode enable.

VMS_SEL

Bit 8: OPAMP inverting input secondary selection.

VPS_SEL

Bits 9-10: OPAMP Non inverting input secondary selection.

CALON

Bit 11: Calibration mode enable.

CALSEL

Bits 12-13: Calibration selection.

PGA_GAIN

Bits 14-17: Gain in PGA mode.

USER_TRIM

Bit 18: User trimming enable.

TRIMOFFSETP

Bits 19-23: Offset trimming value (PMOS).

TRIMOFFSETN

Bits 24-28: Offset trimming value (NMOS).

TSTREF

Bit 29: TSTREF.

OUTCAL

Bit 30: OPAMP ouput status flag.

LOCK

Bit 31: OPAMP lock.

PWR

0x40007000: Power control

4/16 fields covered. Toggle Registers.

CR

power control register

Offset: 0x0, reset: 0x00000000, access: read-write

1/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ENSD3
rw 		ENSD2
rw 		ENSD1
rw 		DBP
rw 		PLS
rw 		PVDE
rw 		CSBF
rw 		CWUF
rw 		PDDS
rw 		LPDS
rw
Toggle Fields.

LPDS

Bit 0: Low-power deep sleep.

PDDS

Bit 1: Power down deepsleep.

Allowed values:
0: STOP_MODE: Enter Stop mode when the CPU enters deepsleep
1: STANDBY_MODE: Enter Standby mode when the CPU enters deepsleep

CWUF

Bit 2: Clear wakeup flag.

CSBF

Bit 3: Clear standby flag.

PVDE

Bit 4: Power voltage detector enable.

PLS

Bits 5-7: PVD level selection.

DBP

Bit 8: Disable backup domain write protection.

ENSD1

Bit 9: ENable SD1 ADC.

ENSD2

Bit 10: ENable SD2 ADC.

ENSD3

Bit 11: ENable SD3 ADC.

CSR

power control/status register

Offset: 0x4, reset: 0x00000000, access: Unspecified

3/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EWUP3
rw 		EWUP2
rw 		EWUP1
rw 		PVDO
r 		SBF
r 		WUF
r
Toggle Fields.

WUF

Bit 0: Wakeup flag.

SBF

Bit 1: Standby flag.

PVDO

Bit 2: PVD output.

EWUP1

Bit 8: Enable WKUP1 pin.

EWUP2

Bit 9: Enable WKUP2 pin.

EWUP3

Bit 10: Enable WKUP3 pin.

RCC

0x40021000: Reset and clock control

164/164 fields covered. Toggle Registers.

CR

Clock control register

Offset: 0x0, reset: 0x00000083, access: Unspecified

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PLLRDY
r 		PLLON
rw 		CSSON
rw 		HSEBYP
rw 		HSERDY
r 		HSEON
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
HSICAL
r 		HSITRIM
rw 		HSIRDY
r 		HSION
rw
Toggle Fields.

HSION

Bit 0: Internal High Speed clock enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

HSIRDY

Bit 1: Internal High Speed clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

HSITRIM

Bits 3-7: Internal High Speed clock trimming.

Allowed values: 0-31

HSICAL

Bits 8-15: Internal High Speed clock Calibration.

Allowed values: 0-255

HSEON

Bit 16: External High Speed clock enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

HSERDY

Bit 17: External High Speed clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

HSEBYP

Bit 18: External High Speed clock Bypass.

Allowed values:
0: NotBypassed: HSE crystal oscillator not bypassed
1: Bypassed: HSE crystal oscillator bypassed with external clock

CSSON

Bit 19: Clock Security System enable.

Allowed values:
0: Off: Clock security system disabled (clock detector OFF)
1: On: Clock security system enable (clock detector ON if the HSE is ready, OFF if not)

PLLON

Bit 24: PLL enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

PLLRDY

Bit 25: PLL clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

CFGR

Clock configuration register (RCC_CFGR)

Offset: 0x4, reset: 0x00000000, access: Unspecified

13/13 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PLLNODIV
N/A 		MCOPRE
N/A 		MCO
rw 		I2SSRC
N/A 		USBPRE
rw 		PLLMUL
rw 		PLLXTPRE
rw 		PLLSRC
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PLLSRC
rw 		PPRE2
rw 		PPRE1
rw 		HPRE
rw 		SWS
r 		SW
rw
Toggle Fields.

SW

Bits 0-1: System clock Switch.

Allowed values:
0: HSI: HSI selected as system clock
1: HSE: HSE selected as system clock
2: PLL: PLL selected as system clock

SWS

Bits 2-3: System Clock Switch Status.

Allowed values:
0: HSI: HSE oscillator used as system clock
1: HSE: HSI oscillator used as system clock
2: PLL: PLL used as system clock

HPRE

Bits 4-7: AHB prescaler.

Allowed values:
0: Div1: SYSCLK not divided
8: Div2: SYSCLK divided by 2
9: Div4: SYSCLK divided by 4
10: Div8: SYSCLK divided by 8
11: Div16: SYSCLK divided by 16
12: Div64: SYSCLK divided by 64
13: Div128: SYSCLK divided by 128
14: Div256: SYSCLK divided by 256
15: Div512: SYSCLK divided by 512

PPRE1

Bits 8-10: APB Low speed prescaler (APB1).

Allowed values:
0: Div1: HCLK not divided
4: Div2: HCLK divided by 2
5: Div4: HCLK divided by 4
6: Div8: HCLK divided by 8
7: Div16: HCLK divided by 16

PPRE2

Bits 11-13: APB high speed prescaler (APB2).

Allowed values:
0: Div1: HCLK not divided
4: Div2: HCLK divided by 2
5: Div4: HCLK divided by 4
6: Div8: HCLK divided by 8
7: Div16: HCLK divided by 16

PLLSRC

Bits 15-16: PLL entry clock source.

Allowed values:
0: HSI_Div2: HSI divided by 2 selected as PLL input clock
1: HSI_Div_PREDIV: HSI divided by PREDIV selected as PLL input clock
2: HSE_Div_PREDIV: HSE divided by PREDIV selected as PLL input clock

PLLXTPRE

Bit 17: HSE divider for PLL entry.

Allowed values:
0: Div1: HSE clock not divided
1: Div2: HSE clock divided by 2

PLLMUL

Bits 18-21: PLL Multiplication Factor.

Allowed values:
0: Mul2: PLL input clock x2
1: Mul3: PLL input clock x3
2: Mul4: PLL input clock x4
3: Mul5: PLL input clock x5
4: Mul6: PLL input clock x6
5: Mul7: PLL input clock x7
6: Mul8: PLL input clock x8
7: Mul9: PLL input clock x9
8: Mul10: PLL input clock x10
9: Mul11: PLL input clock x11
10: Mul12: PLL input clock x12
11: Mul13: PLL input clock x13
12: Mul14: PLL input clock x14
13: Mul15: PLL input clock x15
14: Mul16: PLL input clock x16
15: Mul16x: PLL input clock x16

USBPRE

Bit 22: USB prescaler.

Allowed values:
0: DIV1_5: PLL clock is divided by 1.5
1: DIV1: PLL clock is not divided

I2SSRC

Bit 23: I2S external clock source selection.

Allowed values:
0: SYSCLK: System clock used as I2S clock source
1: CKIN: External clock mapped on the I2S_CKIN pin used as I2S clock source

MCO

Bits 24-26: Microcontroller clock output.

Allowed values:
0: NoMCO: MCO output disabled, no clock on MCO
2: LSI: Internal low speed (LSI) oscillator clock selected
3: LSE: External low speed (LSE) oscillator clock selected
4: SYSCLK: System clock selected
5: HSI: Internal RC 8 MHz (HSI) oscillator clock selected
6: HSE: External 4-32 MHz (HSE) oscillator clock selected
7: PLL: PLL clock selected (divided by 1 or 2, depending en PLLNODIV)

MCOPRE

Bits 28-30: Microcontroller Clock Output Prescaler.

Allowed values:
0: Div1: MCO is divided by 1
1: Div2: MCO is divided by 2
2: Div4: MCO is divided by 4
3: Div8: MCO is divided by 8
4: Div16: MCO is divided by 16
5: Div32: MCO is divided by 32
6: Div64: MCO is divided by 64
7: Div128: MCO is divided by 128

PLLNODIV

Bit 31: Do not divide PLL to MCO.

Allowed values:
0: Div2: PLL is divided by 2 for MCO
1: Div1: PLL is not divided for MCO

CIR

Clock interrupt register (RCC_CIR)

Offset: 0x8, reset: 0x00000000, access: Unspecified

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CSSC
w 		PLLRDYC
w 		HSERDYC
w 		HSIRDYC
w 		LSERDYC
w 		LSIRDYC
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PLLRDYIE
rw 		HSERDYIE
rw 		HSIRDYIE
rw 		LSERDYIE
rw 		LSIRDYIE
rw 		CSSF
r 		PLLRDYF
r 		HSERDYF
r 		HSIRDYF
r 		LSERDYF
r 		LSIRDYF
r
Toggle Fields.

LSIRDYF

Bit 0: LSI Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

LSERDYF

Bit 1: LSE Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

HSIRDYF

Bit 2: HSI Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

HSERDYF

Bit 3: HSE Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

PLLRDYF

Bit 4: PLL Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

CSSF

Bit 7: Clock Security System Interrupt flag.

Allowed values:
0: NotInterrupted: No clock security interrupt caused by HSE clock failure
1: Interrupted: Clock security interrupt caused by HSE clock failure

LSIRDYIE

Bit 8: LSI Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

LSERDYIE

Bit 9: LSE Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSIRDYIE

Bit 10: HSI Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSERDYIE

Bit 11: HSE Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

PLLRDYIE

Bit 12: PLL Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

LSIRDYC

Bit 16: LSI Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

LSERDYC

Bit 17: LSE Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

HSIRDYC

Bit 18: HSI Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

HSERDYC

Bit 19: HSE Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

PLLRDYC

Bit 20: PLL Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

CSSC

Bit 23: Clock security system interrupt clear.

Allowed values:
1: Clear: Clear CSSF flag

APB2RSTR

APB2 peripheral reset register (RCC_APB2RSTR)

Offset: 0xC, reset: 0x00000000, access: read-write

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TIM20RST
rw 		TIM17RST
rw 		TIM16RST
rw 		TIM15RST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SPI4RST
rw 		USART1RST
rw 		TIM8RST
rw 		SPI1RST
rw 		TIM1RST
rw 		SYSCFGRST
rw
Toggle Fields.

SYSCFGRST

Bit 0: SYSCFG and COMP reset.

Allowed values:
1: Reset: Reset the selected module

TIM1RST

Bit 11: TIM1 timer reset.

Allowed values:
1: Reset: Reset the selected module

SPI1RST

Bit 12: SPI 1 reset.

Allowed values:
1: Reset: Reset the selected module

TIM8RST

Bit 13: TIM8 timer reset.

Allowed values:
1: Reset: Reset the selected module

USART1RST

Bit 14: USART1 reset.

Allowed values:
1: Reset: Reset the selected module

SPI4RST

Bit 15: SPI4 reset.

Allowed values:
1: Reset: Reset the selected module

TIM15RST

Bit 16: TIM15 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM16RST

Bit 17: TIM16 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM17RST

Bit 18: TIM17 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM20RST

Bit 20: TIM20 timer reset.

Allowed values:
1: Reset: Reset the selected module

APB1RSTR

APB1 peripheral reset register (RCC_APB1RSTR)

Offset: 0x10, reset: 0x00000000, access: read-write

20/20 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
I2C3RST
rw 		DAC1RST
rw 		PWRRST
rw 		DAC2RST
rw 		CANRST
rw 		USBRST
rw 		I2C2RST
rw 		I2C1RST
rw 		UART5RST
rw 		UART4RST
rw 		USART3RST
rw 		USART2RST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SPI3RST
rw 		SPI2RST
rw 		WWDGRST
rw 		TIM7RST
rw 		TIM6RST
rw 		TIM4RST
rw 		TIM3RST
rw 		TIM2RST
rw
Toggle Fields.

TIM2RST

Bit 0: Timer 2 reset.

Allowed values:
1: Reset: Reset the selected module

TIM3RST

Bit 1: Timer 3 reset.

Allowed values:
1: Reset: Reset the selected module

TIM4RST

Bit 2: Timer 14 reset.

Allowed values:
1: Reset: Reset the selected module

TIM6RST

Bit 4: Timer 6 reset.

Allowed values:
1: Reset: Reset the selected module

TIM7RST

Bit 5: Timer 7 reset.

Allowed values:
1: Reset: Reset the selected module

WWDGRST

Bit 11: Window watchdog reset.

Allowed values:
1: Reset: Reset the selected module

SPI2RST

Bit 14: SPI2 reset.

Allowed values:
1: Reset: Reset the selected module

SPI3RST

Bit 15: SPI3 reset.

Allowed values:
1: Reset: Reset the selected module

USART2RST

Bit 17: USART 2 reset.

Allowed values:
1: Reset: Reset the selected module

USART3RST

Bit 18: USART3 reset.

Allowed values:
1: Reset: Reset the selected module

UART4RST

Bit 19: UART4 reset.

Allowed values:
1: Reset: Reset the selected module

UART5RST

Bit 20: UART5 reset.

Allowed values:
1: Reset: Reset the selected module

I2C1RST

Bit 21: I2C1 reset.

Allowed values:
1: Reset: Reset the selected module

I2C2RST

Bit 22: I2C2 reset.

Allowed values:
1: Reset: Reset the selected module

USBRST

Bit 23: USB reset.

Allowed values:
1: Reset: Reset the selected module

CANRST

Bit 25: CAN reset.

Allowed values:
1: Reset: Reset the selected module

DAC2RST

Bit 26: DAC3 reset.

Allowed values:
1: Reset: Reset the selected module

PWRRST

Bit 28: Power interface reset.

Allowed values:
1: Reset: Reset the selected module

DAC1RST

Bit 29: DAC interface reset.

Allowed values:
1: Reset: Reset the selected module

I2C3RST

Bit 30: I2C3 reset.

Allowed values:
1: Reset: Reset the selected module

AHBENR

AHB Peripheral Clock enable register (RCC_AHBENR)

Offset: 0x14, reset: 0x00000014, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADC34EN
rw 		ADC12EN
rw 		TSCEN
rw 		IOPGEN
rw 		IOPFEN
rw 		IOPEEN
rw 		IOPDEN
rw 		IOPCEN
rw 		IOPBEN
rw 		IOPAEN
rw 		IOPHEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CRCEN
rw 		FLITFEN
rw 		SRAMEN
rw 		DMA2EN
rw 		DMA1EN
rw
Toggle Fields.

DMA1EN

Bit 0: DMA1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

DMA2EN

Bit 1: DMA2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SRAMEN

Bit 2: SRAM interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

FLITFEN

Bit 4: FLITF clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

CRCEN

Bit 6: CRC clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPHEN

Bit 16: I/O port H clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPAEN

Bit 17: I/O port A clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPBEN

Bit 18: I/O port B clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPCEN

Bit 19: I/O port C clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPDEN

Bit 20: I/O port D clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPEEN

Bit 21: I/O port E clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPFEN

Bit 22: I/O port F clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPGEN

Bit 23: I/O port G clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TSCEN

Bit 24: Touch sensing controller clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

ADC12EN

Bit 28: ADC1 and ADC2 enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

ADC34EN

Bit 29: ADC3 and ADC4 enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

APB2ENR

APB2 peripheral clock enable register (RCC_APB2ENR)

Offset: 0x18, reset: 0x00000000, access: read-write

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TIM20EN
rw 		TIM17EN
rw 		TIM16EN
rw 		TIM15EN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SPI4EN
rw 		USART1EN
rw 		TIM8EN
rw 		SPI1EN
rw 		TIM1EN
rw 		SYSCFGEN
rw
Toggle Fields.

SYSCFGEN

Bit 0: SYSCFG clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM1EN

Bit 11: TIM1 Timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI1EN

Bit 12: SPI 1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM8EN

Bit 13: TIM8 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART1EN

Bit 14: USART1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI4EN

Bit 15: SPI4 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM15EN

Bit 16: TIM15 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM16EN

Bit 17: TIM16 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM17EN

Bit 18: TIM17 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM20EN

Bit 20: TIM20 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

APB1ENR

APB1 peripheral clock enable register (RCC_APB1ENR)

Offset: 0x1C, reset: 0x00000000, access: read-write

20/20 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
I2C3EN
rw 		DAC1EN
rw 		PWREN
rw 		DAC2EN
rw 		CANEN
rw 		USBEN
rw 		I2C2EN
rw 		I2C1EN
rw 		UART5EN
rw 		UART4EN
rw 		USART3EN
rw 		USART2EN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SPI3EN
rw 		SPI2EN
rw 		WWDGEN
rw 		TIM7EN
rw 		TIM6EN
rw 		TIM4EN
rw 		TIM3EN
rw 		TIM2EN
rw
Toggle Fields.

TIM2EN

Bit 0: Timer 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM3EN

Bit 1: Timer 3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM4EN

Bit 2: Timer 4 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM6EN

Bit 4: Timer 6 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM7EN

Bit 5: Timer 7 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

WWDGEN

Bit 11: Window watchdog clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI2EN

Bit 14: SPI 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI3EN

Bit 15: SPI 3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART2EN

Bit 17: USART 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART3EN

Bit 18: USART 3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

UART4EN

Bit 19: UART4 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

UART5EN

Bit 20: UART5 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

I2C1EN

Bit 21: I2C 1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

I2C2EN

Bit 22: I2C 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USBEN

Bit 23: USB clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

CANEN

Bit 25: CAN clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

DAC2EN

Bit 26: DAC3 interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

PWREN

Bit 28: Power interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

DAC1EN

Bit 29: DAC interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

I2C3EN

Bit 30: I2C3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

BDCR

Backup domain control register (RCC_BDCR)

Offset: 0x20, reset: 0x00000000, access: Unspecified

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BDRST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RTCEN
rw 		RTCSEL
rw 		LSEDRV
rw 		LSEBYP
rw 		LSERDY
r 		LSEON
rw
Toggle Fields.

LSEON

Bit 0: External Low Speed oscillator enable.

Allowed values:
0: Off: LSE oscillator Off
1: On: LSE oscillator On

LSERDY

Bit 1: External Low Speed oscillator ready.

Allowed values:
0: NotReady: LSE oscillator not ready
1: Ready: LSE oscillator ready

LSEBYP

Bit 2: External Low Speed oscillator bypass.

Allowed values:
0: NotBypassed: LSE crystal oscillator not bypassed
1: Bypassed: LSE crystal oscillator bypassed with external clock

LSEDRV

Bits 3-4: LSE oscillator drive capability.

Allowed values:
0: Low: Low drive capacity
1: MediumHigh: Medium-high drive capacity
2: MediumLow: Medium-low drive capacity
3: High: High drive capacity

RTCSEL

Bits 8-9: RTC clock source selection.

Allowed values:
0: NoClock: No clock
1: LSE: LSE oscillator clock used as RTC clock
2: LSI: LSI oscillator clock used as RTC clock
3: HSE: HSE oscillator clock divided by a prescaler used as RTC clock

RTCEN

Bit 15: RTC clock enable.

Allowed values:
0: Disabled: RTC clock disabled
1: Enabled: RTC clock enabled

BDRST

Bit 16: Backup domain software reset.

Allowed values:
0: Disabled: Reset not activated
1: Enabled: Reset the entire RTC domain

CSR

Control/status register (RCC_CSR)

Offset: 0x24, reset: 0x0C000000, access: Unspecified

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
LPWRRSTF
rw 		WWDGRSTF
rw 		IWDGRSTF
rw 		SFTRSTF
rw 		PORRSTF
rw 		PINRSTF
rw 		OBLRSTF
rw 		RMVF
rw 		V18PWRRSTF
N/A
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LSIRDY
r 		LSION
rw
Toggle Fields.

LSION

Bit 0: Internal low speed oscillator enable.

Allowed values:
0: Off: LSI oscillator Off
1: On: LSI oscillator On

LSIRDY

Bit 1: Internal low speed oscillator ready.

Allowed values:
0: NotReady: LSI oscillator not ready
1: Ready: LSI oscillator ready

V18PWRRSTF

Bit 23: Reset flag of the 1.8 V domain.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

RMVF

Bit 24: Remove reset flag.

Allowed values:
1: Clear: Clears the reset flag

OBLRSTF

Bit 25: Option byte loader reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

PINRSTF

Bit 26: PIN reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

PORRSTF

Bit 27: POR/PDR reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

SFTRSTF

Bit 28: Software reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

IWDGRSTF

Bit 29: Independent watchdog reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

WWDGRSTF

Bit 30: Window watchdog reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

LPWRRSTF

Bit 31: Low-power reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

AHBRSTR

AHB peripheral reset register

Offset: 0x28, reset: 0x00000000, access: read-write

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADC34RST
rw 		ADC12RST
rw 		TSCRST
rw 		IOPGRST
rw 		IOPFRST
rw 		IOPERST
rw 		IOPDRST
rw 		IOPCRST
rw 		IOPBRST
rw 		IOPARST
rw 		IOPHRST
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Toggle Fields.

IOPHRST

Bit 16: I/O port H reset.

Allowed values:
1: Reset: Reset the selected module

IOPARST

Bit 17: I/O port A reset.

Allowed values:
1: Reset: Reset the selected module

IOPBRST

Bit 18: I/O port B reset.

Allowed values:
1: Reset: Reset the selected module

IOPCRST

Bit 19: I/O port C reset.

Allowed values:
1: Reset: Reset the selected module

IOPDRST

Bit 20: I/O port D reset.

Allowed values:
1: Reset: Reset the selected module

IOPERST

Bit 21: I/O port E reset.

Allowed values:
1: Reset: Reset the selected module

IOPFRST

Bit 22: I/O port F reset.

Allowed values:
1: Reset: Reset the selected module

IOPGRST

Bit 23: I/O port G reset.

Allowed values:
1: Reset: Reset the selected module

TSCRST

Bit 24: Touch sensing controller reset.

Allowed values:
1: Reset: Reset the selected module

ADC12RST

Bit 28: ADC1 and ADC2 reset.

Allowed values:
1: Reset: Reset the selected module

ADC34RST

Bit 29: ADC3 and ADC4 reset.

Allowed values:
1: Reset: Reset the selected module

CFGR2

Clock configuration register 2

Offset: 0x2C, reset: 0x00000000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ADC34PRES
rw 		ADC12PRES
rw 		PREDIV
rw
Toggle Fields.

PREDIV

Bits 0-3: PREDIV division factor.

Allowed values:
0: Div1: PREDIV input clock not divided
1: Div2: PREDIV input clock divided by 2
2: Div3: PREDIV input clock divided by 3
3: Div4: PREDIV input clock divided by 4
4: Div5: PREDIV input clock divided by 5
5: Div6: PREDIV input clock divided by 6
6: Div7: PREDIV input clock divided by 7
7: Div8: PREDIV input clock divided by 8
8: Div9: PREDIV input clock divided by 9
9: Div10: PREDIV input clock divided by 10
10: Div11: PREDIV input clock divided by 11
11: Div12: PREDIV input clock divided by 12
12: Div13: PREDIV input clock divided by 13
13: Div14: PREDIV input clock divided by 14
14: Div15: PREDIV input clock divided by 15
15: Div16: PREDIV input clock divided by 16

ADC12PRES

Bits 4-8: ADC1 and ADC2 reset.

Allowed values:
0: NoClock: No clock
16: Div1: PLL clock not divided
17: Div2: PLL clock divided by 2
18: Div4: PLL clock divided by 4
19: Div6: PLL clock divided by 6
20: Div8: PLL clock divided by 8
21: Div10: PLL clock divided by 10
22: Div12: PLL clock divided by 12
23: Div16: PLL clock divided by 16
24: Div32: PLL clock divided by 32
25: Div64: PLL clock divided by 64
26: Div128: PLL clock divided by 128
27: Div256: PLL clock divided by 256

ADC34PRES

Bits 9-13: ADC3 and ADC4 reset.

Allowed values:
0: NoClock: No clock
16: Div1: PLL clock not divided
17: Div2: PLL clock divided by 2
18: Div4: PLL clock divided by 4
19: Div6: PLL clock divided by 6
20: Div8: PLL clock divided by 8
21: Div10: PLL clock divided by 10
22: Div12: PLL clock divided by 12
23: Div16: PLL clock divided by 16
24: Div32: PLL clock divided by 32
25: Div64: PLL clock divided by 64
26: Div128: PLL clock divided by 128
27: Div256: PLL clock divided by 256

CFGR3

Clock configuration register 3

Offset: 0x30, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TIM34SW
rw 		TIM2SW
rw 		UART5SW
rw 		UART4SW
rw 		USART3SW
rw 		USART2SW
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TIM20SW
rw 		TIM17SW
rw 		TIM16SW
rw 		TIM15SW
rw 		TIM8SW
rw 		TIM1SW
rw 		I2C3SW
rw 		I2C2SW
rw 		I2C1SW
rw 		USART1SW
rw
Toggle Fields.

USART1SW

Bits 0-1: USART1 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

I2C1SW

Bit 4: I2C1 clock source selection.

Allowed values:
0: HSI: HSI clock selected as I2C clock source
1: SYSCLK: SYSCLK clock selected as I2C clock source

I2C2SW

Bit 5: I2C2 clock source selection.

Allowed values:
0: HSI: HSI clock selected as I2C clock source
1: SYSCLK: SYSCLK clock selected as I2C clock source

I2C3SW

Bit 6: I2C3 clock source selection.

Allowed values:
0: HSI: HSI clock selected as I2C clock source
1: SYSCLK: SYSCLK clock selected as I2C clock source

TIM1SW

Bit 8: Timer1 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM8SW

Bit 9: Timer8 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM15SW

Bit 10: Timer15 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM16SW

Bit 11: Timer16 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM17SW

Bit 13: Timer17 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM20SW

Bit 15: Timer20 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

USART2SW

Bits 16-17: USART2 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

USART3SW

Bits 18-19: USART3 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

UART4SW

Bits 20-21: UART4 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

UART5SW

Bits 22-23: UART5 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

TIM2SW

Bit 24: Timer2 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM34SW

Bit 25: Timer34 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

RTC

0x40002800: Real-time clock

124/124 fields covered. Toggle Registers.

TR

time register

Offset: 0x0, reset: 0x00000000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PM
rw 		HT
rw 		HU
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MNT
rw 		MNU
rw 		ST
rw 		SU
rw
Toggle Fields.

SU

Bits 0-3: Second units in BCD format.

Allowed values: 0-15

ST

Bits 4-6: Second tens in BCD format.

Allowed values: 0-7

MNU

Bits 8-11: Minute units in BCD format.

Allowed values: 0-15

MNT

Bits 12-14: Minute tens in BCD format.

Allowed values: 0-7

HU

Bits 16-19: Hour units in BCD format.

Allowed values: 0-15

HT

Bits 20-21: Hour tens in BCD format.

Allowed values: 0-3

PM

Bit 22: AM/PM notation.

Allowed values:
0: AM: AM or 24-hour format
1: PM: PM

DR

date register

Offset: 0x4, reset: 0x00002101, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
YT
rw 		YU
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
WDU
rw 		MT
rw 		MU
rw 		DT
rw 		DU
rw
Toggle Fields.

DU

Bits 0-3: Date units in BCD format.

Allowed values: 0-15

DT

Bits 4-5: Date tens in BCD format.

Allowed values: 0-3

MU

Bits 8-11: Month units in BCD format.

Allowed values: 0-15

MT

Bit 12: Month tens in BCD format.

Allowed values: 0-1

WDU

Bits 13-15: Week day units.

Allowed values: 1-7

YU

Bits 16-19: Year units in BCD format.

Allowed values: 0-15

YT

Bits 20-23: Year tens in BCD format.

Allowed values: 0-15

CR

control register

Offset: 0x8, reset: 0x00000000, access: read-write

20/20 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COE
rw 		OSEL
rw 		POL
rw 		COSEL
rw 		BKP
rw 		SUB1H
rw 		ADD1H
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TSIE
rw 		WUTIE
rw 		ALRBIE
rw 		ALRAIE
rw 		TSE
rw 		WUTE
rw 		ALRBE
rw 		ALRAE
rw 		FMT
rw 		BYPSHAD
rw 		REFCKON
rw 		TSEDGE
rw 		WUCKSEL
rw
Toggle Fields.

WUCKSEL

Bits 0-2: Wakeup clock selection.

Allowed values:
0: Div16: RTC/16 clock is selected
1: Div8: RTC/8 clock is selected
2: Div4: RTC/4 clock is selected
3: Div2: RTC/2 clock is selected
4: ClockSpare: ck_spre (usually 1 Hz) clock is selected
6: ClockSpareWithOffset: ck_spre (usually 1 Hz) clock is selected and 2^16 is added to the WUT counter value

TSEDGE

Bit 3: Time-stamp event active edge.

Allowed values:
0: RisingEdge: RTC_TS input rising edge generates a time-stamp event
1: FallingEdge: RTC_TS input falling edge generates a time-stamp event

REFCKON

Bit 4: Reference clock detection enable (50 or 60 Hz).

Allowed values:
0: Disabled: RTC_REFIN detection disabled
1: Enabled: RTC_REFIN detection enabled

BYPSHAD

Bit 5: Bypass the shadow registers.

Allowed values:
0: ShadowReg: Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken from the shadow registers, which are updated once every two RTCCLK cycles
1: BypassShadowReg: Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken directly from the calendar counters

FMT

Bit 6: Hour format.

Allowed values:
0: Twenty_Four_Hour: 24 hour/day format
1: AM_PM: AM/PM hour format

ALRAE

Bit 8: Alarm A enable.

Allowed values:
0: Disabled: Alarm A disabled
1: Enabled: Alarm A enabled

ALRBE

Bit 9: Alarm B enable.

Allowed values:
0: Disabled: Alarm B disabled
1: Enabled: Alarm B enabled

WUTE

Bit 10: Wakeup timer enable.

Allowed values:
0: Disabled: Wakeup timer disabled
1: Enabled: Wakeup timer enabled

TSE

Bit 11: Time stamp enable.

Allowed values:
0: Disabled: Timestamp disabled
1: Enabled: Timestamp enabled

ALRAIE

Bit 12: Alarm A interrupt enable.

Allowed values:
0: Disabled: Alarm A interrupt disabled
1: Enabled: Alarm A interrupt enabled

ALRBIE

Bit 13: Alarm B interrupt enable.

Allowed values:
0: Disabled: Alarm B Interrupt disabled
1: Enabled: Alarm B Interrupt enabled

WUTIE

Bit 14: Wakeup timer interrupt enable.

Allowed values:
0: Disabled: Wakeup timer interrupt disabled
1: Enabled: Wakeup timer interrupt enabled

TSIE

Bit 15: Time-stamp interrupt enable.

Allowed values:
0: Disabled: Time-stamp Interrupt disabled
1: Enabled: Time-stamp Interrupt enabled

ADD1H

Bit 16: Add 1 hour (summer time change).

Allowed values:
1: Add1: Adds 1 hour to the current time. This can be used for summer time change outside initialization mode

SUB1H

Bit 17: Subtract 1 hour (winter time change).

Allowed values:
1: Sub1: Subtracts 1 hour to the current time. This can be used for winter time change outside initialization mode

BKP

Bit 18: Backup.

Allowed values:
0: DST_Not_Changed: Daylight Saving Time change has not been performed
1: DST_Changed: Daylight Saving Time change has been performed

COSEL

Bit 19: Calibration output selection.

Allowed values:
0: CalFreq_512Hz: Calibration output is 512 Hz (with default prescaler setting)
1: CalFreq_1Hz: Calibration output is 1 Hz (with default prescaler setting)

POL

Bit 20: Output polarity.

Allowed values:
0: High: The pin is high when ALRAF/ALRBF/WUTF is asserted (depending on OSEL[1:0])
1: Low: The pin is low when ALRAF/ALRBF/WUTF is asserted (depending on OSEL[1:0])

OSEL

Bits 21-22: Output selection.

Allowed values:
0: Disabled: Output disabled
1: AlarmA: Alarm A output enabled
2: AlarmB: Alarm B output enabled
3: Wakeup: Wakeup output enabled

COE

Bit 23: Calibration output enable.

Allowed values:
0: Disabled: Calibration output disabled
1: Enabled: Calibration output enabled

ISR

initialization and status register

Offset: 0xC, reset: 0x00000007, access: Unspecified

17/17 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RECALPF
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TAMP3F
rw 		TAMP2F
rw 		TAMP1F
rw 		TSOVF
rw 		TSF
rw 		WUTF
rw 		ALRBF
rw 		ALRAF
rw 		INIT
rw 		INITF
r 		RSF
rw 		INITS
r 		SHPF
rw 		WUTWF
r 		ALRBWF
r 		ALRAWF
r
Toggle Fields.

ALRAWF

Bit 0: Alarm A write flag.

Allowed values:
0: UpdateNotAllowed: Alarm update not allowed
1: UpdateAllowed: Alarm update allowed

ALRBWF

Bit 1: Alarm B write flag.

Allowed values:
0: UpdateNotAllowed: Alarm update not allowed
1: UpdateAllowed: Alarm update allowed

WUTWF

Bit 2: Wakeup timer write flag.

Allowed values:
0: UpdateNotAllowed: Wakeup timer configuration update not allowed
1: UpdateAllowed: Wakeup timer configuration update allowed

SHPF

Bit 3: Shift operation pending.

Allowed values:
0: NoShiftPending: No shift operation is pending
1: ShiftPending: A shift operation is pending

INITS

Bit 4: Initialization status flag.

Allowed values:
0: NotInitalized: Calendar has not been initialized
1: Initalized: Calendar has been initialized

RSF

Bit 5: Registers synchronization flag.

Allowed values:
0: NotSynced: Calendar shadow registers not yet synchronized
1: Synced: Calendar shadow registers synchronized

INITF

Bit 6: Initialization flag.

Allowed values:
0: NotAllowed: Calendar registers update is not allowed
1: Allowed: Calendar registers update is allowed

INIT

Bit 7: Initialization mode.

Allowed values:
0: FreeRunningMode: Free running mode
1: InitMode: Initialization mode used to program time and date register (RTC_TR and RTC_DR), and prescaler register (RTC_PRER). Counters are stopped and start counting from the new value when INIT is reset.

ALRAF

Bit 8: Alarm A flag.

Allowed values:
1: Match: This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm A register (RTC_ALRMAR)

ALRBF

Bit 9: Alarm B flag.

Allowed values:
1: Match: This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm B register (RTC_ALRMBR)

WUTF

Bit 10: Wakeup timer flag.

Allowed values:
1: Zero: This flag is set by hardware when the wakeup auto-reload counter reaches 0

TSF

Bit 11: Time-stamp flag.

Allowed values:
1: TimestampEvent: This flag is set by hardware when a time-stamp event occurs

TSOVF

Bit 12: Time-stamp overflow flag.

Allowed values:
1: Overflow: This flag is set by hardware when a time-stamp event occurs while TSF is already set

TAMP1F

Bit 13: Tamper detection flag.

Allowed values:
1: Tampered: This flag is set by hardware when a tamper detection event is detected on the RTC_TAMPx input

TAMP2F

Bit 14: RTC_TAMP2 detection flag.

Allowed values:
1: Tampered: This flag is set by hardware when a tamper detection event is detected on the RTC_TAMPx input

TAMP3F

Bit 15: RTC_TAMP3 detection flag.

Allowed values:
1: Tampered: This flag is set by hardware when a tamper detection event is detected on the RTC_TAMPx input

RECALPF

Bit 16: Recalibration pending Flag.

Allowed values:
1: Pending: The RECALPF status flag is automatically set to 1 when software writes to the RTC_CALR register, indicating that the RTC_CALR register is blocked. When the new calibration settings are taken into account, this bit returns to 0

PRER

prescaler register

Offset: 0x10, reset: 0x007F00FF, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PREDIV_A
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PREDIV_S
rw
Toggle Fields.

PREDIV_S

Bits 0-14: Synchronous prescaler factor.

Allowed values: 0-32767

PREDIV_A

Bits 16-22: Asynchronous prescaler factor.

Allowed values: 0-127

WUTR

wakeup timer register

Offset: 0x14, reset: 0x0000FFFF, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
WUT
rw
Toggle Fields.

WUT

Bits 0-15: Wakeup auto-reload value bits.

Allowed values: 0-65535

ALRMAR

alarm A register

Offset: 0x1C, reset: 0x00000000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MSK4
rw 		WDSEL
rw 		DT
rw 		DU
rw 		MSK3
rw 		PM
rw 		HT
rw 		HU
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MSK2
rw 		MNT
rw 		MNU
rw 		MSK1
rw 		ST
rw 		SU
rw
Toggle Fields.

SU

Bits 0-3: Second units in BCD format.

Allowed values: 0-15

ST

Bits 4-6: Second tens in BCD format.

Allowed values: 0-7

MSK1

Bit 7: Alarm A seconds mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

MNU

Bits 8-11: Minute units in BCD format.

Allowed values: 0-15

MNT

Bits 12-14: Minute tens in BCD format.

Allowed values: 0-7

MSK2

Bit 15: Alarm A minutes mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

HU

Bits 16-19: Hour units in BCD format.

Allowed values: 0-15

HT

Bits 20-21: Hour tens in BCD format.

Allowed values: 0-3

PM

Bit 22: AM/PM notation.

Allowed values:
0: AM: AM or 24-hour format
1: PM: PM

MSK3

Bit 23: Alarm A hours mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

DU

Bits 24-27: Date units or day in BCD format.

Allowed values: 0-15

DT

Bits 28-29: Date tens in BCD format.

Allowed values: 0-3

WDSEL

Bit 30: Week day selection.

Allowed values:
0: DateUnits: DU[3:0] represents the date units
1: WeekDay: DU[3:0] represents the week day. DT[1:0] is don’t care.

MSK4

Bit 31: Alarm A date mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

ALRMBR

alarm B register

Offset: 0x20, reset: 0x00000000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MSK4
rw 		WDSEL
rw 		DT
rw 		DU
rw 		MSK3
rw 		PM
rw 		HT
rw 		HU
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MSK2
rw 		MNT
rw 		MNU
rw 		MSK1
rw 		ST
rw 		SU
rw
Toggle Fields.

SU

Bits 0-3: Second units in BCD format.

Allowed values: 0-15

ST

Bits 4-6: Second tens in BCD format.

Allowed values: 0-7

MSK1

Bit 7: Alarm B seconds mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

MNU

Bits 8-11: Minute units in BCD format.

Allowed values: 0-15

MNT

Bits 12-14: Minute tens in BCD format.

Allowed values: 0-7

MSK2

Bit 15: Alarm B minutes mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

HU

Bits 16-19: Hour units in BCD format.

Allowed values: 0-15

HT

Bits 20-21: Hour tens in BCD format.

Allowed values: 0-3

PM

Bit 22: AM/PM notation.

Allowed values:
0: AM: AM or 24-hour format
1: PM: PM

MSK3

Bit 23: Alarm B hours mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

DU

Bits 24-27: Date units or day in BCD format.

Allowed values: 0-15

DT

Bits 28-29: Date tens in BCD format.

Allowed values: 0-3

WDSEL

Bit 30: Week day selection.

Allowed values:
0: DateUnits: DU[3:0] represents the date units
1: WeekDay: DU[3:0] represents the week day. DT[1:0] is don’t care.

MSK4

Bit 31: Alarm B date mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

WPR

write protection register

Offset: 0x24, reset: 0x00000000, access: write-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
KEY
w
Toggle Fields.

KEY

Bits 0-7: Write protection key.

Allowed values: 0-255

SSR

sub second register

Offset: 0x28, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SS
r
Toggle Fields.

SS

Bits 0-15: Sub second value.

Allowed values: 0-65535

SHIFTR

shift control register

Offset: 0x2C, reset: 0x00000000, access: write-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADD1S
w
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SUBFS
w
Toggle Fields.

SUBFS

Bits 0-14: Subtract a fraction of a second.

Allowed values: 0-32767

ADD1S

Bit 31: Add one second.

Allowed values:
1: Add1: Add one second to the clock/calendar

TSTR

time stamp time register

Offset: 0x30, reset: 0x00000000, access: read-only

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PM
r 		HT
r 		HU
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MNT
r 		MNU
r 		ST
r 		SU
r
Toggle Fields.

SU

Bits 0-3: Second units in BCD format.

ST

Bits 4-6: Second tens in BCD format.

MNU

Bits 8-11: Minute units in BCD format.

MNT

Bits 12-14: Minute tens in BCD format.

HU

Bits 16-19: Hour units in BCD format.

HT

Bits 20-21: Hour tens in BCD format.

PM

Bit 22: AM/PM notation.

TSDR

time stamp date register

Offset: 0x34, reset: 0x00000000, access: read-only

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
WDU
r 		MT
r 		MU
r 		DT
r 		DU
r
Toggle Fields.

DU

Bits 0-3: Date units in BCD format.

DT

Bits 4-5: Date tens in BCD format.

MU

Bits 8-11: Month units in BCD format.

MT

Bit 12: Month tens in BCD format.

WDU

Bits 13-15: Week day units.

TSSSR

timestamp sub second register

Offset: 0x38, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SS
r
Toggle Fields.

SS

Bits 0-15: Sub second value.

CALR

calibration register

Offset: 0x3C, reset: 0x00000000, access: read-write

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CALP
rw 		CALW8
rw 		CALW16
rw 		CALM
rw
Toggle Fields.

CALM

Bits 0-8: Calibration minus.

Allowed values: 0-511

CALW16

Bit 13: Use a 16-second calibration cycle period.

Allowed values:
1: Sixteen_Second: When CALW16 is set to ‘1’, the 16-second calibration cycle period is selected.This bit must not be set to ‘1’ if CALW8=1

CALW8

Bit 14: Use an 8-second calibration cycle period.

Allowed values:
1: Eight_Second: When CALW8 is set to ‘1’, the 8-second calibration cycle period is selected

CALP

Bit 15: Increase frequency of RTC by 488.5 ppm.

Allowed values:
0: NoChange: No RTCCLK pulses are added
1: IncreaseFreq: One RTCCLK pulse is effectively inserted every 2^11 pulses (frequency increased by 488.5 ppm)

TAFCR

tamper and alternate function configuration register

Offset: 0x40, reset: 0x00000000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PC15MODE
rw 		PC15VALUE
rw 		PC14MODE
rw 		PC14VALUE
rw 		PC13MODE
rw 		PC13VALUE
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TAMPPUDIS
rw 		TAMPPRCH
rw 		TAMPFLT
rw 		TAMPFREQ
rw 		TAMPTS
rw 		TAMP2TRG
rw 		TAMP2E
rw 		TAMPIE
rw 		TAMP1TRG
rw 		TAMP1E
rw
Toggle Fields.

TAMP1E

Bit 0: Tamper 1 detection enable.

Allowed values:
0: Disabled: RTC_TAMPx input detection disabled
1: Enabled: RTC_TAMPx input detection enabled

TAMP1TRG

Bit 1: Active level for tamper 1.

Allowed values:
0: RisingEdge: If TAMPFLT = 00: RTC_TAMPx input rising edge triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input staying low triggers a tamper detection event.
1: FallingEdge: If TAMPFLT = 00: RTC_TAMPx input staying high triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input falling edge triggers a tamper detection event

TAMPIE

Bit 2: Tamper interrupt enable.

Allowed values:
0: Disabled: Tamper interrupt disabled
1: Enabled: Tamper interrupt enabled

TAMP2E

Bit 3: Tamper 2 detection enable.

Allowed values:
0: Disabled: RTC_TAMPx input detection disabled
1: Enabled: RTC_TAMPx input detection enabled

TAMP2TRG

Bit 4: Active level for tamper 2.

Allowed values:
0: RisingEdge: If TAMPFLT = 00: RTC_TAMPx input rising edge triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input staying low triggers a tamper detection event.
1: FallingEdge: If TAMPFLT = 00: RTC_TAMPx input staying high triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input falling edge triggers a tamper detection event

TAMPTS

Bit 7: Activate timestamp on tamper detection event.

Allowed values:
0: NoSave: Tamper detection event does not cause a timestamp to be saved
1: Save: Save timestamp on tamper detection event

TAMPFREQ

Bits 8-10: Tamper sampling frequency.

Allowed values:
0: Div32768: RTCCLK / 32768 (1 Hz when RTCCLK = 32768 Hz)
1: Div16384: RTCCLK / 16384 (2 Hz when RTCCLK = 32768 Hz)
2: Div8192: RTCCLK / 8192 (4 Hz when RTCCLK = 32768 Hz)
3: Div4096: RTCCLK / 4096 (8 Hz when RTCCLK = 32768 Hz)
4: Div2048: RTCCLK / 2048 (16 Hz when RTCCLK = 32768 Hz)
5: Div1024: RTCCLK / 1024 (32 Hz when RTCCLK = 32768 Hz)
6: Div512: RTCCLK / 512 (64 Hz when RTCCLK = 32768 Hz)
7: Div256: RTCCLK / 256 (128 Hz when RTCCLK = 32768 Hz)

TAMPFLT

Bits 11-12: Tamper filter count.

Allowed values:
0: Immediate: Tamper event is activated on edge of RTC_TAMPx input transitions to the active level (no internal pull-up on RTC_TAMPx input)
1: Samples2: Tamper event is activated after 2 consecutive samples at the active level
2: Samples4: Tamper event is activated after 4 consecutive samples at the active level
3: Samples8: Tamper event is activated after 8 consecutive samples at the active level

TAMPPRCH

Bits 13-14: Tamper precharge duration.

Allowed values:
0: Cycles1: 1 RTCCLK cycle
1: Cycles2: 2 RTCCLK cycles
2: Cycles4: 4 RTCCLK cycles
3: Cycles8: 8 RTCCLK cycles

TAMPPUDIS

Bit 15: TAMPER pull-up disable.

Allowed values:
0: Enabled: Precharge RTC_TAMPx pins before sampling (enable internal pull-up)
1: Disabled: Disable precharge of RTC_TAMPx pins

PC13VALUE

Bit 18: PC13 value.

Allowed values:
1: High: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic high
0: Low: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic low

PC13MODE

Bit 19: PC13 mode.

Allowed values:
0: Floating: PCx is controlled by the GPIO configuration Register. Consequently PC15 is floating in Standby mode
1: PushPull: PCx is forced to push-pull output if LSE is disabled

PC14VALUE

Bit 20: PC14 value.

Allowed values:
1: High: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic high
0: Low: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic low

PC14MODE

Bit 21: PC 14 mode.

Allowed values:
0: Floating: PCx is controlled by the GPIO configuration Register. Consequently PC15 is floating in Standby mode
1: PushPull: PCx is forced to push-pull output if LSE is disabled

PC15VALUE

Bit 22: PC15 value.

Allowed values:
1: High: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic high
0: Low: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic low

PC15MODE

Bit 23: PC15 mode.

Allowed values:
0: Floating: PCx is controlled by the GPIO configuration Register. Consequently PC15 is floating in Standby mode
1: PushPull: PCx is forced to push-pull output if LSE is disabled

ALRMASSR

alarm A sub second register

Offset: 0x44, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MASKSS
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SS
rw
Toggle Fields.

SS

Bits 0-14: Sub seconds value.

Allowed values: 0-32767

MASKSS

Bits 24-27: Mask the most-significant bits starting at this bit.

Allowed values: 0-15

ALRMBSSR

alarm B sub second register

Offset: 0x48, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MASKSS
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SS
rw
Toggle Fields.

SS

Bits 0-14: Sub seconds value.

Allowed values: 0-32767

MASKSS

Bits 24-27: Mask the most-significant bits starting at this bit.

Allowed values: 0-15

BKP%sR

backup register

Offset: 0x50, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BKP
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BKP
rw
Toggle Fields.

BKP

Bits 0-31: BKP.

Allowed values: 0-4294967295

SCB

0xE000ED00: System control block

5/74 fields covered. Toggle Registers.

CPUID

CPUID base register

Offset: 0x0, reset: 0x410FC241, access: read-only

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
Implementer
r 		Variant
r 		Constant
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PartNo
r 		Revision
r
Toggle Fields.

Revision

Bits 0-3: Revision number.

PartNo

Bits 4-15: Part number of the processor.

Constant

Bits 16-19: Reads as 0xF.

Variant

Bits 20-23: Variant number.

Implementer

Bits 24-31: Implementer code.

ICSR

Interrupt control and state register

Offset: 0x4, reset: 0x00000000, access: read-write

0/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
NMIPENDSET
rw 		PENDSVSET
rw 		PENDSVCLR
rw 		PENDSTSET
rw 		PENDSTCLR
rw 		ISRPENDING
rw 		VECTPENDING
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
VECTPENDING
rw 		RETTOBASE
rw 		VECTACTIVE
rw
Toggle Fields.

VECTACTIVE

Bits 0-8: Active vector.

RETTOBASE

Bit 11: Return to base level.

VECTPENDING

Bits 12-18: Pending vector.

ISRPENDING

Bit 22: Interrupt pending flag.

PENDSTCLR

Bit 25: SysTick exception clear-pending bit.

PENDSTSET

Bit 26: SysTick exception set-pending bit.

PENDSVCLR

Bit 27: PendSV clear-pending bit.

PENDSVSET

Bit 28: PendSV set-pending bit.

NMIPENDSET

Bit 31: NMI set-pending bit..

VTOR

Vector table offset register

Offset: 0x8, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
TBLOFF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TBLOFF
rw
Toggle Fields.

TBLOFF

Bits 9-29: Vector table base offset field.

AIRCR

Application interrupt and reset control register

Offset: 0xC, reset: 0x00000000, access: read-write

0/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
VECTKEYSTAT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ENDIANESS
rw 		PRIGROUP
rw 		SYSRESETREQ
rw 		VECTCLRACTIVE
rw 		VECTRESET
rw
Toggle Fields.

VECTRESET

Bit 0: VECTRESET.

VECTCLRACTIVE

Bit 1: VECTCLRACTIVE.

SYSRESETREQ

Bit 2: SYSRESETREQ.

PRIGROUP

Bits 8-10: PRIGROUP.

ENDIANESS

Bit 15: ENDIANESS.

VECTKEYSTAT

Bits 16-31: Register key.

SCR

System control register

Offset: 0x10, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SEVEONPEND
rw 		SLEEPDEEP
rw 		SLEEPONEXIT
rw
Toggle Fields.

SLEEPONEXIT

Bit 1: SLEEPONEXIT.

SLEEPDEEP

Bit 2: SLEEPDEEP.

SEVEONPEND

Bit 4: Send Event on Pending bit.

CCR

Configuration and control register

Offset: 0x14, reset: 0x00000000, access: read-write

0/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
STKALIGN
rw 		BFHFNMIGN
rw 		DIV_0_TRP
rw 		UNALIGN__TRP
rw 		USERSETMPEND
rw 		NONBASETHRDENA
rw
Toggle Fields.

NONBASETHRDENA

Bit 0: Configures how the processor enters Thread mode.

USERSETMPEND

Bit 1: USERSETMPEND.

UNALIGN__TRP

Bit 3: UNALIGN_ TRP.

DIV_0_TRP

Bit 4: DIV_0_TRP.

BFHFNMIGN

Bit 8: BFHFNMIGN.

STKALIGN

Bit 9: STKALIGN.

SHPR1

System handler priority registers

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PRI_6
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PRI_5
rw 		PRI_4
rw
Toggle Fields.

PRI_4

Bits 0-7: Priority of system handler 4.

PRI_5

Bits 8-15: Priority of system handler 5.

PRI_6

Bits 16-23: Priority of system handler 6.

SHPR2

System handler priority registers

Offset: 0x1C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PRI_11
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Toggle Fields.

PRI_11

Bits 24-31: Priority of system handler 11.

SHPR3

System handler priority registers

Offset: 0x20, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
PRI_15
rw 		PRI_14
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Toggle Fields.

PRI_14

Bits 16-23: Priority of system handler 14.

PRI_15

Bits 24-31: Priority of system handler 15.

SHCRS

System handler control and state register

Offset: 0x24, reset: 0x00000000, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
USGFAULTENA
rw 		BUSFAULTENA
rw 		MEMFAULTENA
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SVCALLPENDED
rw 		BUSFAULTPENDED
rw 		MEMFAULTPENDED
rw 		USGFAULTPENDED
rw 		SYSTICKACT
rw 		PENDSVACT
rw 		MONITORACT
rw 		SVCALLACT
rw 		USGFAULTACT
rw 		BUSFAULTACT
rw 		MEMFAULTACT
rw
Toggle Fields.

MEMFAULTACT

Bit 0: Memory management fault exception active bit.

BUSFAULTACT

Bit 1: Bus fault exception active bit.

USGFAULTACT

Bit 3: Usage fault exception active bit.

SVCALLACT

Bit 7: SVC call active bit.

MONITORACT

Bit 8: Debug monitor active bit.

PENDSVACT

Bit 10: PendSV exception active bit.

SYSTICKACT

Bit 11: SysTick exception active bit.

USGFAULTPENDED

Bit 12: Usage fault exception pending bit.

MEMFAULTPENDED

Bit 13: Memory management fault exception pending bit.

BUSFAULTPENDED

Bit 14: Bus fault exception pending bit.

SVCALLPENDED

Bit 15: SVC call pending bit.

MEMFAULTENA

Bit 16: Memory management fault enable bit.

BUSFAULTENA

Bit 17: Bus fault enable bit.

USGFAULTENA

Bit 18: Usage fault enable bit.

CFSR_UFSR_BFSR_MMFSR

Configurable fault status register

Offset: 0x28, reset: 0x00000000, access: read-write

0/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DIVBYZERO
rw 		UNALIGNED
rw 		NOCP
rw 		INVPC
rw 		INVSTATE
rw 		UNDEFINSTR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BFARVALID
rw 		LSPERR
rw 		STKERR
rw 		UNSTKERR
rw 		IMPRECISERR
rw 		PRECISERR
rw 		IBUSERR
rw 		MMARVALID
rw 		MLSPERR
rw 		MSTKERR
rw 		MUNSTKERR
rw 		IACCVIOL
rw
Toggle Fields.

IACCVIOL

Bit 1: Instruction access violation flag.

MUNSTKERR

Bit 3: Memory manager fault on unstacking for a return from exception.

MSTKERR

Bit 4: Memory manager fault on stacking for exception entry..

MLSPERR

Bit 5: MLSPERR.

MMARVALID

Bit 7: Memory Management Fault Address Register (MMAR) valid flag.

IBUSERR

Bit 8: Instruction bus error.

PRECISERR

Bit 9: Precise data bus error.

IMPRECISERR

Bit 10: Imprecise data bus error.

UNSTKERR

Bit 11: Bus fault on unstacking for a return from exception.

STKERR

Bit 12: Bus fault on stacking for exception entry.

LSPERR

Bit 13: Bus fault on floating-point lazy state preservation.

BFARVALID

Bit 15: Bus Fault Address Register (BFAR) valid flag.

UNDEFINSTR

Bit 16: Undefined instruction usage fault.

INVSTATE

Bit 17: Invalid state usage fault.

INVPC

Bit 18: Invalid PC load usage fault.

NOCP

Bit 19: No coprocessor usage fault..

UNALIGNED

Bit 24: Unaligned access usage fault.

DIVBYZERO

Bit 25: Divide by zero usage fault.

HFSR

Hard fault status register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
DEBUG_VT
rw 		FORCED
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
VECTTBL
rw
Toggle Fields.

VECTTBL

Bit 1: Vector table hard fault.

FORCED

Bit 30: Forced hard fault.

DEBUG_VT

Bit 31: Reserved for Debug use.

MMFAR

Memory management fault address register

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MMFAR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MMFAR
rw
Toggle Fields.

MMFAR

Bits 0-31: Memory management fault address.

BFAR

Bus fault address register

Offset: 0x38, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BFAR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BFAR
rw
Toggle Fields.

BFAR

Bits 0-31: Bus fault address.

AFSR

Auxiliary fault status register

Offset: 0x3C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
IMPDEF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IMPDEF
rw
Toggle Fields.

IMPDEF

Bits 0-31: Implementation defined.

SCB_ACTRL

0xE000E008: System control block ACTLR

0/5 fields covered. Toggle Registers.

ACTRL

Auxiliary control register

Offset: 0x0, reset: 0x00000000, access: read-write

0/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DISOOFP
rw 		DISFPCA
rw 		DISFOLD
rw 		DISDEFWBUF
rw 		DISMCYCINT
rw
Toggle Fields.

DISMCYCINT

Bit 0: DISMCYCINT.

DISDEFWBUF

Bit 1: DISDEFWBUF.

DISFOLD

Bit 2: DISFOLD.

DISFPCA

Bit 8: DISFPCA.

DISOOFP

Bit 9: DISOOFP.

SDADC1

0x40016000: Sigma-delta analog-to-digital converter

21/72 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x00000000, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
INIT
rw 		RDMAEN
rw 		JDMAEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RSYNC
rw 		JSYNC
rw 		PDI
rw 		SBI
rw 		SLOWCK
rw 		REFV
rw 		ROVRIE
rw 		REOCIE
rw 		JOVRIE
rw 		JEOCIE
rw 		EOCALIE
rw
Toggle Fields.

EOCALIE

Bit 0: End of calibration interrupt enable.

JEOCIE

Bit 1: Injected end of conversion interrupt enable.

JOVRIE

Bit 2: Injected data overrun interrupt enable.

REOCIE

Bit 3: Regular end of conversion interrupt enable.

ROVRIE

Bit 4: Regular data overrun interrupt enable.

REFV

Bits 8-9: Reference voltage selection.

SLOWCK

Bit 10: Slow clock mode enable.

SBI

Bit 11: Enter Standby mode when idle.

PDI

Bit 12: Enter power down mode when idle.

JSYNC

Bit 14: Launch a injected conversion synchronously with SDADC1.

RSYNC

Bit 15: Launch regular conversion synchronously with SDADC1.

JDMAEN

Bit 16: DMA channel enabled to read data for the injected channel group.

RDMAEN

Bit 17: DMA channel enabled to read data for the regular channel.

INIT

Bit 31: Initialization mode request.

CR2

control register 2

Offset: 0x4, reset: 0x00000000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FAST
rw 		RSWSTART
rw 		RCONT
rw 		RCH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JSWSTART
rw 		JEXTEN
rw 		JEXTSEL
rw 		JDS
rw 		JCONT
rw 		STARTCALIB
rw 		CALIBCNT
rw 		ADON
rw
Toggle Fields.

ADON

Bit 0: SDADC enable.

CALIBCNT

Bits 1-2: Number of calibration sequences to be performed (number of valid configurations).

STARTCALIB

Bit 4: Start calibration.

JCONT

Bit 5: Continuous mode selection for injected conversions.

JDS

Bit 6: Delay start of injected conversions..

JEXTSEL

Bits 8-11: Trigger signal selection for launching injected conversions.

JEXTEN

Bits 13-14: Trigger enable and trigger edge selection for injected conversions.

JSWSTART

Bit 15: Start a conversion of the injected group of channels.

RCH

Bits 16-19: Regular channel selection.

RCONT

Bit 22: Continuous mode selection for regular conversions.

RSWSTART

Bit 23: Software start of a conversion on the regular channel.

FAST

Bit 24: Fast conversion mode selection.

ISR

interrupt and status register

Offset: 0x8, reset: 0x00000000, access: read-only

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
INITRDY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
STABIP
r 		RCIP
r 		JCIP
r 		CALIBIP
r 		ROVRF
r 		REOCF
r 		JOVRF
r 		JEOCF
r 		EOCALF
r
Toggle Fields.

EOCALF

Bit 0: End of calibration flag.

JEOCF

Bit 1: End of injected conversion flag.

JOVRF

Bit 2: Injected conversion overrun flag.

REOCF

Bit 3: End of regular conversion flag.

ROVRF

Bit 4: Regular conversion overrun flag.

CALIBIP

Bit 12: Calibration in progress status.

JCIP

Bit 13: Injected conversion in progress status.

RCIP

Bit 14: Regular conversion in progress status.

STABIP

Bit 15: Stabilization in progress status.

INITRDY

Bit 31: Initialization mode is ready.

CLRISR

interrupt and status clear register

Offset: 0xC, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRROVRF
rw 		CLRJOVRF
rw 		CLREOCALF
rw
Toggle Fields.

CLREOCALF

Bit 0: Clear the end of calibration flag.

CLRJOVRF

Bit 2: Clear the injected conversion overrun flag.

CLRROVRF

Bit 4: Clear the regular conversion overrun flag.

JCHGR

injected channel group selection register

Offset: 0x14, reset: 0x00000001, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JCHG
rw
Toggle Fields.

JCHG

Bits 0-8: Injected channel group selection.

CONF0R

configuration 0 register

Offset: 0x20, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON0
rw 		SE0
rw 		GAIN0
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET0
rw
Toggle Fields.

OFFSET0

Bits 0-11: Twelve-bit calibration offset for configuration 0.

GAIN0

Bits 20-22: Gain setting for configuration 0.

SE0

Bits 26-27: Single-ended mode for configuration 0.

COMMON0

Bits 30-31: Common mode for configuration 0.

CONF1R

configuration 1 register

Offset: 0x24, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON1
rw 		SE1
rw 		GAIN1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET1
rw
Toggle Fields.

OFFSET1

Bits 0-11: Twelve-bit calibration offset for configuration 1.

GAIN1

Bits 20-22: Gain setting for configuration 1.

SE1

Bits 26-27: Single-ended mode for configuration 1.

COMMON1

Bits 30-31: Common mode for configuration 1.

CONF2R

configuration 2 register

Offset: 0x28, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON2
rw 		SE2
rw 		GAIN2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET2
rw
Toggle Fields.

OFFSET2

Bits 0-11: Twelve-bit calibration offset for configuration 2.

GAIN2

Bits 20-22: Gain setting for configuration 2.

SE2

Bits 26-27: Single-ended mode for configuration 2.

COMMON2

Bits 30-31: Common mode for configuration 2.

CONFCHR1

channel configuration register 1

Offset: 0x40, reset: 0x00000000, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CONFCH7
rw 		CONFCH6
rw 		CONFCH5
rw 		CONFCH4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CONFCH3
rw 		CONFCH2
rw 		CONFCH1
rw 		CONFCH0
rw
Toggle Fields.

CONFCH0

Bits 0-1: CONFCH0.

CONFCH1

Bits 4-5: CONFCH1.

CONFCH2

Bits 8-9: CONFCH2.

CONFCH3

Bits 12-13: CONFCH3.

CONFCH4

Bits 16-17: CONFCH4.

CONFCH5

Bits 20-21: CONFCH5.

CONFCH6

Bits 24-25: CONFCH6.

CONFCH7

Bits 28-29: CONFCH7.

CONFCHR2

channel configuration register 2

Offset: 0x44, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CONFCH8
rw
Toggle Fields.

CONFCH8

Bits 0-1: Channel 8 configuration.

JDATAR

data register for injected group

Offset: 0x60, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATACH
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA
r
Toggle Fields.

JDATA

Bits 0-15: Injected group conversion data.

JDATACH

Bits 25-28: Injected channel most recently converted.

RDATAR

data register for the regular channel

Offset: 0x64, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA
r
Toggle Fields.

RDATA

Bits 0-15: Regular channel conversion data.

JDATA12R

SDADC1 and SDADC2 injected data register

Offset: 0x70, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATA2
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: Injected group conversion data for SDADC1.

JDATA2

Bits 16-31: Injected group conversion data for SDADC2.

RDATA12R

SDADC1 and SDADC2 regular data register

Offset: 0x74, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RDATA2
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA1
r
Toggle Fields.

RDATA1

Bits 0-15: Regular conversion data for SDADC1.

RDATA2

Bits 16-31: Regular conversion data for SDADC2.

JDATA13R

SDADC1 and SDADC3 injected data register

Offset: 0x78, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATA3
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: Injected group conversion data for SDADC1.

JDATA3

Bits 16-31: Injected group conversion data for SDADC3.

RDATA13R

SDADC1 and SDADC3 regular data register

Offset: 0x7C, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RDATA3
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA1
r
Toggle Fields.

RDATA1

Bits 0-15: Regular conversion data for SDADC1.

RDATA3

Bits 16-31: Regular conversion data for SDADC3.

SDADC2

0x40016400: Sigma-delta analog-to-digital converter

21/72 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x00000000, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
INIT
rw 		RDMAEN
rw 		JDMAEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RSYNC
rw 		JSYNC
rw 		PDI
rw 		SBI
rw 		SLOWCK
rw 		REFV
rw 		ROVRIE
rw 		REOCIE
rw 		JOVRIE
rw 		JEOCIE
rw 		EOCALIE
rw
Toggle Fields.

EOCALIE

Bit 0: End of calibration interrupt enable.

JEOCIE

Bit 1: Injected end of conversion interrupt enable.

JOVRIE

Bit 2: Injected data overrun interrupt enable.

REOCIE

Bit 3: Regular end of conversion interrupt enable.

ROVRIE

Bit 4: Regular data overrun interrupt enable.

REFV

Bits 8-9: Reference voltage selection.

SLOWCK

Bit 10: Slow clock mode enable.

SBI

Bit 11: Enter Standby mode when idle.

PDI

Bit 12: Enter power down mode when idle.

JSYNC

Bit 14: Launch a injected conversion synchronously with SDADC1.

RSYNC

Bit 15: Launch regular conversion synchronously with SDADC1.

JDMAEN

Bit 16: DMA channel enabled to read data for the injected channel group.

RDMAEN

Bit 17: DMA channel enabled to read data for the regular channel.

INIT

Bit 31: Initialization mode request.

CR2

control register 2

Offset: 0x4, reset: 0x00000000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FAST
rw 		RSWSTART
rw 		RCONT
rw 		RCH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JSWSTART
rw 		JEXTEN
rw 		JEXTSEL
rw 		JDS
rw 		JCONT
rw 		STARTCALIB
rw 		CALIBCNT
rw 		ADON
rw
Toggle Fields.

ADON

Bit 0: SDADC enable.

CALIBCNT

Bits 1-2: Number of calibration sequences to be performed (number of valid configurations).

STARTCALIB

Bit 4: Start calibration.

JCONT

Bit 5: Continuous mode selection for injected conversions.

JDS

Bit 6: Delay start of injected conversions..

JEXTSEL

Bits 8-11: Trigger signal selection for launching injected conversions.

JEXTEN

Bits 13-14: Trigger enable and trigger edge selection for injected conversions.

JSWSTART

Bit 15: Start a conversion of the injected group of channels.

RCH

Bits 16-19: Regular channel selection.

RCONT

Bit 22: Continuous mode selection for regular conversions.

RSWSTART

Bit 23: Software start of a conversion on the regular channel.

FAST

Bit 24: Fast conversion mode selection.

ISR

interrupt and status register

Offset: 0x8, reset: 0x00000000, access: read-only

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
INITRDY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
STABIP
r 		RCIP
r 		JCIP
r 		CALIBIP
r 		ROVRF
r 		REOCF
r 		JOVRF
r 		JEOCF
r 		EOCALF
r
Toggle Fields.

EOCALF

Bit 0: End of calibration flag.

JEOCF

Bit 1: End of injected conversion flag.

JOVRF

Bit 2: Injected conversion overrun flag.

REOCF

Bit 3: End of regular conversion flag.

ROVRF

Bit 4: Regular conversion overrun flag.

CALIBIP

Bit 12: Calibration in progress status.

JCIP

Bit 13: Injected conversion in progress status.

RCIP

Bit 14: Regular conversion in progress status.

STABIP

Bit 15: Stabilization in progress status.

INITRDY

Bit 31: Initialization mode is ready.

CLRISR

interrupt and status clear register

Offset: 0xC, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRROVRF
rw 		CLRJOVRF
rw 		CLREOCALF
rw
Toggle Fields.

CLREOCALF

Bit 0: Clear the end of calibration flag.

CLRJOVRF

Bit 2: Clear the injected conversion overrun flag.

CLRROVRF

Bit 4: Clear the regular conversion overrun flag.

JCHGR

injected channel group selection register

Offset: 0x14, reset: 0x00000001, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JCHG
rw
Toggle Fields.

JCHG

Bits 0-8: Injected channel group selection.

CONF0R

configuration 0 register

Offset: 0x20, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON0
rw 		SE0
rw 		GAIN0
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET0
rw
Toggle Fields.

OFFSET0

Bits 0-11: Twelve-bit calibration offset for configuration 0.

GAIN0

Bits 20-22: Gain setting for configuration 0.

SE0

Bits 26-27: Single-ended mode for configuration 0.

COMMON0

Bits 30-31: Common mode for configuration 0.

CONF1R

configuration 1 register

Offset: 0x24, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON1
rw 		SE1
rw 		GAIN1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET1
rw
Toggle Fields.

OFFSET1

Bits 0-11: Twelve-bit calibration offset for configuration 1.

GAIN1

Bits 20-22: Gain setting for configuration 1.

SE1

Bits 26-27: Single-ended mode for configuration 1.

COMMON1

Bits 30-31: Common mode for configuration 1.

CONF2R

configuration 2 register

Offset: 0x28, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON2
rw 		SE2
rw 		GAIN2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET2
rw
Toggle Fields.

OFFSET2

Bits 0-11: Twelve-bit calibration offset for configuration 2.

GAIN2

Bits 20-22: Gain setting for configuration 2.

SE2

Bits 26-27: Single-ended mode for configuration 2.

COMMON2

Bits 30-31: Common mode for configuration 2.

CONFCHR1

channel configuration register 1

Offset: 0x40, reset: 0x00000000, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CONFCH7
rw 		CONFCH6
rw 		CONFCH5
rw 		CONFCH4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CONFCH3
rw 		CONFCH2
rw 		CONFCH1
rw 		CONFCH0
rw
Toggle Fields.

CONFCH0

Bits 0-1: CONFCH0.

CONFCH1

Bits 4-5: CONFCH1.

CONFCH2

Bits 8-9: CONFCH2.

CONFCH3

Bits 12-13: CONFCH3.

CONFCH4

Bits 16-17: CONFCH4.

CONFCH5

Bits 20-21: CONFCH5.

CONFCH6

Bits 24-25: CONFCH6.

CONFCH7

Bits 28-29: CONFCH7.

CONFCHR2

channel configuration register 2

Offset: 0x44, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CONFCH8
rw
Toggle Fields.

CONFCH8

Bits 0-1: Channel 8 configuration.

JDATAR

data register for injected group

Offset: 0x60, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATACH
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA
r
Toggle Fields.

JDATA

Bits 0-15: Injected group conversion data.

JDATACH

Bits 25-28: Injected channel most recently converted.

RDATAR

data register for the regular channel

Offset: 0x64, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA
r
Toggle Fields.

RDATA

Bits 0-15: Regular channel conversion data.

JDATA12R

SDADC1 and SDADC2 injected data register

Offset: 0x70, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATA2
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: Injected group conversion data for SDADC1.

JDATA2

Bits 16-31: Injected group conversion data for SDADC2.

RDATA12R

SDADC1 and SDADC2 regular data register

Offset: 0x74, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RDATA2
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA1
r
Toggle Fields.

RDATA1

Bits 0-15: Regular conversion data for SDADC1.

RDATA2

Bits 16-31: Regular conversion data for SDADC2.

JDATA13R

SDADC1 and SDADC3 injected data register

Offset: 0x78, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATA3
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: Injected group conversion data for SDADC1.

JDATA3

Bits 16-31: Injected group conversion data for SDADC3.

RDATA13R

SDADC1 and SDADC3 regular data register

Offset: 0x7C, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RDATA3
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA1
r
Toggle Fields.

RDATA1

Bits 0-15: Regular conversion data for SDADC1.

RDATA3

Bits 16-31: Regular conversion data for SDADC3.

SDADC3

0x40016800: Sigma-delta analog-to-digital converter

21/72 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x00000000, access: read-write

0/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
INIT
rw 		RDMAEN
rw 		JDMAEN
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RSYNC
rw 		JSYNC
rw 		PDI
rw 		SBI
rw 		SLOWCK
rw 		REFV
rw 		ROVRIE
rw 		REOCIE
rw 		JOVRIE
rw 		JEOCIE
rw 		EOCALIE
rw
Toggle Fields.

EOCALIE

Bit 0: End of calibration interrupt enable.

JEOCIE

Bit 1: Injected end of conversion interrupt enable.

JOVRIE

Bit 2: Injected data overrun interrupt enable.

REOCIE

Bit 3: Regular end of conversion interrupt enable.

ROVRIE

Bit 4: Regular data overrun interrupt enable.

REFV

Bits 8-9: Reference voltage selection.

SLOWCK

Bit 10: Slow clock mode enable.

SBI

Bit 11: Enter Standby mode when idle.

PDI

Bit 12: Enter power down mode when idle.

JSYNC

Bit 14: Launch a injected conversion synchronously with SDADC1.

RSYNC

Bit 15: Launch regular conversion synchronously with SDADC1.

JDMAEN

Bit 16: DMA channel enabled to read data for the injected channel group.

RDMAEN

Bit 17: DMA channel enabled to read data for the regular channel.

INIT

Bit 31: Initialization mode request.

CR2

control register 2

Offset: 0x4, reset: 0x00000000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FAST
rw 		RSWSTART
rw 		RCONT
rw 		RCH
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JSWSTART
rw 		JEXTEN
rw 		JEXTSEL
rw 		JDS
rw 		JCONT
rw 		STARTCALIB
rw 		CALIBCNT
rw 		ADON
rw
Toggle Fields.

ADON

Bit 0: SDADC enable.

CALIBCNT

Bits 1-2: Number of calibration sequences to be performed (number of valid configurations).

STARTCALIB

Bit 4: Start calibration.

JCONT

Bit 5: Continuous mode selection for injected conversions.

JDS

Bit 6: Delay start of injected conversions..

JEXTSEL

Bits 8-11: Trigger signal selection for launching injected conversions.

JEXTEN

Bits 13-14: Trigger enable and trigger edge selection for injected conversions.

JSWSTART

Bit 15: Start a conversion of the injected group of channels.

RCH

Bits 16-19: Regular channel selection.

RCONT

Bit 22: Continuous mode selection for regular conversions.

RSWSTART

Bit 23: Software start of a conversion on the regular channel.

FAST

Bit 24: Fast conversion mode selection.

ISR

interrupt and status register

Offset: 0x8, reset: 0x00000000, access: read-only

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
INITRDY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
STABIP
r 		RCIP
r 		JCIP
r 		CALIBIP
r 		ROVRF
r 		REOCF
r 		JOVRF
r 		JEOCF
r 		EOCALF
r
Toggle Fields.

EOCALF

Bit 0: End of calibration flag.

JEOCF

Bit 1: End of injected conversion flag.

JOVRF

Bit 2: Injected conversion overrun flag.

REOCF

Bit 3: End of regular conversion flag.

ROVRF

Bit 4: Regular conversion overrun flag.

CALIBIP

Bit 12: Calibration in progress status.

JCIP

Bit 13: Injected conversion in progress status.

RCIP

Bit 14: Regular conversion in progress status.

STABIP

Bit 15: Stabilization in progress status.

INITRDY

Bit 31: Initialization mode is ready.

CLRISR

interrupt and status clear register

Offset: 0xC, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLRROVRF
rw 		CLRJOVRF
rw 		CLREOCALF
rw
Toggle Fields.

CLREOCALF

Bit 0: Clear the end of calibration flag.

CLRJOVRF

Bit 2: Clear the injected conversion overrun flag.

CLRROVRF

Bit 4: Clear the regular conversion overrun flag.

JCHGR

injected channel group selection register

Offset: 0x14, reset: 0x00000001, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JCHG
rw
Toggle Fields.

JCHG

Bits 0-8: Injected channel group selection.

CONF0R

configuration 0 register

Offset: 0x20, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON0
rw 		SE0
rw 		GAIN0
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET0
rw
Toggle Fields.

OFFSET0

Bits 0-11: Twelve-bit calibration offset for configuration 0.

GAIN0

Bits 20-22: Gain setting for configuration 0.

SE0

Bits 26-27: Single-ended mode for configuration 0.

COMMON0

Bits 30-31: Common mode for configuration 0.

CONF1R

configuration 1 register

Offset: 0x24, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON1
rw 		SE1
rw 		GAIN1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET1
rw
Toggle Fields.

OFFSET1

Bits 0-11: Twelve-bit calibration offset for configuration 1.

GAIN1

Bits 20-22: Gain setting for configuration 1.

SE1

Bits 26-27: Single-ended mode for configuration 1.

COMMON1

Bits 30-31: Common mode for configuration 1.

CONF2R

configuration 2 register

Offset: 0x28, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COMMON2
rw 		SE2
rw 		GAIN2
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OFFSET2
rw
Toggle Fields.

OFFSET2

Bits 0-11: Twelve-bit calibration offset for configuration 2.

GAIN2

Bits 20-22: Gain setting for configuration 2.

SE2

Bits 26-27: Single-ended mode for configuration 2.

COMMON2

Bits 30-31: Common mode for configuration 2.

CONFCHR1

channel configuration register 1

Offset: 0x40, reset: 0x00000000, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CONFCH7
rw 		CONFCH6
rw 		CONFCH5
rw 		CONFCH4
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CONFCH3
rw 		CONFCH2
rw 		CONFCH1
rw 		CONFCH0
rw
Toggle Fields.

CONFCH0

Bits 0-1: CONFCH0.

CONFCH1

Bits 4-5: CONFCH1.

CONFCH2

Bits 8-9: CONFCH2.

CONFCH3

Bits 12-13: CONFCH3.

CONFCH4

Bits 16-17: CONFCH4.

CONFCH5

Bits 20-21: CONFCH5.

CONFCH6

Bits 24-25: CONFCH6.

CONFCH7

Bits 28-29: CONFCH7.

CONFCHR2

channel configuration register 2

Offset: 0x44, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CONFCH8
rw
Toggle Fields.

CONFCH8

Bits 0-1: Channel 8 configuration.

JDATAR

data register for injected group

Offset: 0x60, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATACH
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA
r
Toggle Fields.

JDATA

Bits 0-15: Injected group conversion data.

JDATACH

Bits 25-28: Injected channel most recently converted.

RDATAR

data register for the regular channel

Offset: 0x64, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA
r
Toggle Fields.

RDATA

Bits 0-15: Regular channel conversion data.

JDATA12R

SDADC1 and SDADC2 injected data register

Offset: 0x70, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATA2
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: Injected group conversion data for SDADC1.

JDATA2

Bits 16-31: Injected group conversion data for SDADC2.

RDATA12R

SDADC1 and SDADC2 regular data register

Offset: 0x74, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RDATA2
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA1
r
Toggle Fields.

RDATA1

Bits 0-15: Regular conversion data for SDADC1.

RDATA2

Bits 16-31: Regular conversion data for SDADC2.

JDATA13R

SDADC1 and SDADC3 injected data register

Offset: 0x78, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
JDATA3
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
JDATA1
r
Toggle Fields.

JDATA1

Bits 0-15: Injected group conversion data for SDADC1.

JDATA3

Bits 16-31: Injected group conversion data for SDADC3.

RDATA13R

SDADC1 and SDADC3 regular data register

Offset: 0x7C, reset: 0x00000000, access: read-only

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RDATA3
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDATA1
r
Toggle Fields.

RDATA1

Bits 0-15: Regular conversion data for SDADC1.

RDATA3

Bits 16-31: Regular conversion data for SDADC3.

SPI1

0x40013000: Serial peripheral interface/Inter-IC sound

52/52 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BIDIMODE
rw 		BIDIOE
rw 		CRCEN
rw 		CRCNEXT
rw 		CRCL
rw 		RXONLY
rw 		SSM
rw 		SSI
rw 		LSBFIRST
rw 		SPE
rw 		BR
rw 		MSTR
rw 		CPOL
rw 		CPHA
rw
Toggle Fields.

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LDMA_TX
rw 		LDMA_RX
rw 		FRXTH
rw 		DS
rw 		TXEIE
rw 		RXNEIE
rw 		ERRIE
rw 		FRF
rw 		NSSP
rw 		SSOE
rw 		TXDMAEN
rw 		RXDMAEN
rw
Toggle Fields.

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, reset: 0x0002, access: Unspecified

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FTLVL
r 		FRLVL
r 		TIFRFE
r 		BSY
r 		OVR
r 		MODF
r 		CRCERR
rw 		UDR
r 		CHSIDE
r 		TXE
r 		RXNE
r
Toggle Fields.

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

TIFRFE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DR
rw
Toggle Fields.

DR

Bits 0-15: Data register.

Allowed values: 0-65535

CRCPR

CRC polynomial register

Offset: 0x10, reset: 0x0007, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CRCPOLY
rw
Toggle Fields.

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0-65535

RXCRCR

RX CRC register

Offset: 0x14, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RxCRC
r
Toggle Fields.

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0-65535

TXCRCR

TX CRC register

Offset: 0x18, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TxCRC
r
Toggle Fields.

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0-65535

I2SCFGR

I2S configuration register

Offset: 0x1C, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I2SMOD
rw 		I2SE
rw 		I2SCFG
rw 		PCMSYNC
rw 		I2SSTD
rw 		CKPOL
rw 		DATLEN
rw 		CHLEN
rw
Toggle Fields.

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, reset: 0x00000010, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCKOE
rw 		ODD
rw 		I2SDIV
rw
Toggle Fields.

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 2-255

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SPI2

0x40003800: Serial peripheral interface/Inter-IC sound

52/52 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BIDIMODE
rw 		BIDIOE
rw 		CRCEN
rw 		CRCNEXT
rw 		CRCL
rw 		RXONLY
rw 		SSM
rw 		SSI
rw 		LSBFIRST
rw 		SPE
rw 		BR
rw 		MSTR
rw 		CPOL
rw 		CPHA
rw
Toggle Fields.

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LDMA_TX
rw 		LDMA_RX
rw 		FRXTH
rw 		DS
rw 		TXEIE
rw 		RXNEIE
rw 		ERRIE
rw 		FRF
rw 		NSSP
rw 		SSOE
rw 		TXDMAEN
rw 		RXDMAEN
rw
Toggle Fields.

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, reset: 0x0002, access: Unspecified

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FTLVL
r 		FRLVL
r 		TIFRFE
r 		BSY
r 		OVR
r 		MODF
r 		CRCERR
rw 		UDR
r 		CHSIDE
r 		TXE
r 		RXNE
r
Toggle Fields.

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

TIFRFE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DR
rw
Toggle Fields.

DR

Bits 0-15: Data register.

Allowed values: 0-65535

CRCPR

CRC polynomial register

Offset: 0x10, reset: 0x0007, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CRCPOLY
rw
Toggle Fields.

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0-65535

RXCRCR

RX CRC register

Offset: 0x14, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RxCRC
r
Toggle Fields.

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0-65535

TXCRCR

TX CRC register

Offset: 0x18, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TxCRC
r
Toggle Fields.

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0-65535

I2SCFGR

I2S configuration register

Offset: 0x1C, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I2SMOD
rw 		I2SE
rw 		I2SCFG
rw 		PCMSYNC
rw 		I2SSTD
rw 		CKPOL
rw 		DATLEN
rw 		CHLEN
rw
Toggle Fields.

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, reset: 0x00000010, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCKOE
rw 		ODD
rw 		I2SDIV
rw
Toggle Fields.

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 2-255

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SPI3

0x40003C00: Serial peripheral interface/Inter-IC sound

52/52 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BIDIMODE
rw 		BIDIOE
rw 		CRCEN
rw 		CRCNEXT
rw 		CRCL
rw 		RXONLY
rw 		SSM
rw 		SSI
rw 		LSBFIRST
rw 		SPE
rw 		BR
rw 		MSTR
rw 		CPOL
rw 		CPHA
rw
Toggle Fields.

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LDMA_TX
rw 		LDMA_RX
rw 		FRXTH
rw 		DS
rw 		TXEIE
rw 		RXNEIE
rw 		ERRIE
rw 		FRF
rw 		NSSP
rw 		SSOE
rw 		TXDMAEN
rw 		RXDMAEN
rw
Toggle Fields.

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, reset: 0x0002, access: Unspecified

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FTLVL
r 		FRLVL
r 		TIFRFE
r 		BSY
r 		OVR
r 		MODF
r 		CRCERR
rw 		UDR
r 		CHSIDE
r 		TXE
r 		RXNE
r
Toggle Fields.

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

TIFRFE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DR
rw
Toggle Fields.

DR

Bits 0-15: Data register.

Allowed values: 0-65535

CRCPR

CRC polynomial register

Offset: 0x10, reset: 0x0007, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CRCPOLY
rw
Toggle Fields.

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0-65535

RXCRCR

RX CRC register

Offset: 0x14, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RxCRC
r
Toggle Fields.

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0-65535

TXCRCR

TX CRC register

Offset: 0x18, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TxCRC
r
Toggle Fields.

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0-65535

I2SCFGR

I2S configuration register

Offset: 0x1C, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I2SMOD
rw 		I2SE
rw 		I2SCFG
rw 		PCMSYNC
rw 		I2SSTD
rw 		CKPOL
rw 		DATLEN
rw 		CHLEN
rw
Toggle Fields.

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, reset: 0x00000010, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCKOE
rw 		ODD
rw 		I2SDIV
rw
Toggle Fields.

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 2-255

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SPI4

0x40013C00: Serial peripheral interface/Inter-IC sound

52/52 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BIDIMODE
rw 		BIDIOE
rw 		CRCEN
rw 		CRCNEXT
rw 		CRCL
rw 		RXONLY
rw 		SSM
rw 		SSI
rw 		LSBFIRST
rw 		SPE
rw 		BR
rw 		MSTR
rw 		CPOL
rw 		CPHA
rw
Toggle Fields.

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
LDMA_TX
rw 		LDMA_RX
rw 		FRXTH
rw 		DS
rw 		TXEIE
rw 		RXNEIE
rw 		ERRIE
rw 		FRF
rw 		NSSP
rw 		SSOE
rw 		TXDMAEN
rw 		RXDMAEN
rw
Toggle Fields.

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, reset: 0x0002, access: Unspecified

11/11 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FTLVL
r 		FRLVL
r 		TIFRFE
r 		BSY
r 		OVR
r 		MODF
r 		CRCERR
rw 		UDR
r 		CHSIDE
r 		TXE
r 		RXNE
r
Toggle Fields.

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

TIFRFE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DR
rw
Toggle Fields.

DR

Bits 0-15: Data register.

Allowed values: 0-65535

CRCPR

CRC polynomial register

Offset: 0x10, reset: 0x0007, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CRCPOLY
rw
Toggle Fields.

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0-65535

RXCRCR

RX CRC register

Offset: 0x14, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RxCRC
r
Toggle Fields.

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0-65535

TXCRCR

TX CRC register

Offset: 0x18, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TxCRC
r
Toggle Fields.

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0-65535

I2SCFGR

I2S configuration register

Offset: 0x1C, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
I2SMOD
rw 		I2SE
rw 		I2SCFG
rw 		PCMSYNC
rw 		I2SSTD
rw 		CKPOL
rw 		DATLEN
rw 		CHLEN
rw
Toggle Fields.

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, reset: 0x00000010, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCKOE
rw 		ODD
rw 		I2SDIV
rw
Toggle Fields.

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 2-255

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

STK

0xE000E010: SysTick timer

0/9 fields covered. Toggle Registers.

CTRL

SysTick control and status register

Offset: 0x0, reset: 0X00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
COUNTFLAG
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CLKSOURCE
rw 		TICKINT
rw 		ENABLE
rw
Toggle Fields.

ENABLE

Bit 0: Counter enable.

TICKINT

Bit 1: SysTick exception request enable.

CLKSOURCE

Bit 2: Clock source selection.

COUNTFLAG

Bit 16: COUNTFLAG.

LOAD

SysTick reload value register

Offset: 0x4, reset: 0X00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
RELOAD
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RELOAD
rw
Toggle Fields.

RELOAD

Bits 0-23: RELOAD value.

VAL

SysTick current value register

Offset: 0x8, reset: 0X00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CURRENT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CURRENT
rw
Toggle Fields.

CURRENT

Bits 0-23: Current counter value.

CALIB

SysTick calibration value register

Offset: 0xC, reset: 0X00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
NOREF
rw 		SKEW
rw 		TENMS
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TENMS
rw
Toggle Fields.

TENMS

Bits 0-23: Calibration value.

SKEW

Bit 30: SKEW flag: Indicates whether the TENMS value is exact.

NOREF

Bit 31: NOREF flag. Reads as zero.

SYSCFG

0x40010000: System configuration controller

80/80 fields covered. Toggle Registers.

CFGR1

configuration register 1

Offset: 0x0, reset: 0x00000000, access: read-write

24/24 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FPU_IE5
rw 		FPU_IE4
rw 		FPU_IE3
rw 		FPU_IE2
rw 		FPU_IE1
rw 		FPU_IE0
rw 		I2C3_FMP
rw 		ENCODER_MODE
rw 		I2C2_FMP
rw 		I2C1_FMP
rw 		I2C_PB9_FMP
rw 		I2C_PB8_FMP
rw 		I2C_PB7_FMP
rw 		I2C_PB6_FMP
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DAC2_CH1_DMA_RMP
rw 		TIM7_DAC1_CH2_DMA_RMP
rw 		TIM6_DAC1_CH1_DMA_RMP
rw 		TIM17_DMA_RMP
rw 		TIM16_DMA_RMP
rw 		ADC2_DMA_RMP
rw 		DAC1_TRIG_RMP
rw 		TIM1_ITR3_RMP
rw 		USB_IT_RMP
rw 		MEM_MODE
rw
Toggle Fields.

MEM_MODE

Bits 0-2: Memory mapping selection bits.

Allowed values:
0: MainFlash: Main Flash memory mapped at 0x0000_0000
1: SystemFlash: System Flash memory mapped at 0x0000_0000
3: SRAM: Embedded SRAM mapped at 0x0000_0000
4: FMC: FMC Bank (Only the first two banks) (Available on STM32F303xD/E only)

USB_IT_RMP

Bit 5: USB interrupt remap.

Allowed values:
0: NotRemapped: USB_HP, USB_LP and USB_WAKEUP interrupts are mapped on interrupt lines 19, 20 and 42 respectively
1: Remapped: USB_HP, USB_LP and USB_WAKEUP interrupts are mapped on interrupt lines 74, 75 and 76 respectively

TIM1_ITR3_RMP

Bit 6: Timer 1 ITR3 selection.

Allowed values:
0: NotRemapped: TIM1_ITR3 = TIM4_TRGO in STM32F303xB/C and STM32F358xC devices
1: Remapped: TIM1_ITR3 = TIM17_OC

DAC1_TRIG_RMP

Bit 7: DAC trigger remap (when TSEL = 001).

Allowed values:
0: NotRemapped: DAC trigger is TIM8_TRGO in STM32F303xB/C and STM32F358xC devices
1: Remapped: DAC trigger is TIM3_TRGO

ADC2_DMA_RMP

Bit 8: ADC24 DMA remapping bit.

Allowed values:
0: NotRemapped: ADC24 DMA requests mapped on DMA2 channels 1 and 2
1: Remapped: ADC24 DMA requests mapped on DMA2 channels 3 and 4

TIM16_DMA_RMP

Bit 11: TIM16 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM16_CH1 and TIM16_UP DMA requests mapped on DMA channel 3
1: Remapped: TIM16_CH1 and TIM16_UP DMA requests mapped on DMA channel 4

TIM17_DMA_RMP

Bit 12: TIM17 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM17_CH1 and TIM17_UP DMA requests mapped on DMA channel 1
1: Remapped: TIM17_CH1 and TIM17_UP DMA requests mapped on DMA channel 2

TIM6_DAC1_CH1_DMA_RMP

Bit 13: TIM6 and DAC1 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM6_UP and DAC_CH1 DMA requests mapped on DMA2 channel 3 in STM32F303xB/C and STM32F358xC
1: Remapped: TIM6_UP and DAC_CH1 DMA requests mapped on DMA1 channel 3

TIM7_DAC1_CH2_DMA_RMP

Bit 14: TIM7 and DAC2 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM7_UP and DAC_CH2 DMA requests mapped on DMA2 channel 4 in STM32F303xB/C and STM32F358xC devices
1: Remapped: TIM7_UP and DAC_CH2 DMA requests mapped on DMA1 channel 4

DAC2_CH1_DMA_RMP

Bit 15: DAC2 channel1 DMA remap.

Allowed values:
0: NotRemapped: Not remapped
1: Remapped: DAC2_CH1 DMA requests mapped on DMA1 channel 5

I2C_PB6_FMP

Bit 16: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB6 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB6 and the Speed control is bypassed

I2C_PB7_FMP

Bit 17: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB7 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB7 and the Speed control is bypassed

I2C_PB8_FMP

Bit 18: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB8 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB8 and the Speed control is bypassed

I2C_PB9_FMP

Bit 19: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB9 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB9 and the Speed control is bypassed

I2C1_FMP

Bit 20: I2C1 Fast Mode Plus.

Allowed values:
0: Standard: FM+ mode is controlled by I2C_Pxx_FMP bits only
1: FMP: FM+ mode is enabled on all I2C1 pins selected through selection through IOPORT control registers AF selection bits

I2C2_FMP

Bit 21: I2C2 Fast Mode Plus.

Allowed values:
0: Standard: FM+ mode is controlled by I2C_Pxx_FMP bits only
1: FMP: FM+ mode is enabled on all I2C2 pins selected through selection through IOPORT control registers AF selection bits

ENCODER_MODE

Bits 22-23: Encoder mode.

Allowed values:
0: NoRedirection: No redirection
1: MapTim2Tim15: TIM2 IC1 and TIM2 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively
2: MapTim3Tim15: TIM3 IC1 and TIM3 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively
3: MapTim4Tim15: TIM4 IC1 and TIM4 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively (STM32F303xB/C and STM32F358xC devices only)

I2C3_FMP

Bit 24: I2C3 Fast Mode Plus.

Allowed values:
0: Standard: FM+ mode is controlled by I2C_Pxx_FMP bits only
1: FMP: FM+ mode is enabled on all I2C3 pins selected through selection through IOPORT control registers AF selection bits

FPU_IE0

Bit 26: Invalid operation interrupt enable.

Allowed values:
0: Disabled: Invalid operation interrupt disable
1: Enabled: Invalid operation interrupt enable

FPU_IE1

Bit 27: Devide-by-zero interrupt enable.

Allowed values:
0: Disabled: Devide-by-zero interrupt disable
1: Enabled: Devide-by-zero interrupt enable

FPU_IE2

Bit 28: Underflow interrupt enable.

Allowed values:
0: Disabled: Underflow interrupt disable
1: Enabled: Underflow interrupt enable

FPU_IE3

Bit 29: Overflow interrupt enable.

Allowed values:
0: Disabled: Overflow interrupt disable
1: Enabled: Overflow interrupt enable

FPU_IE4

Bit 30: Input denormal interrupt enable.

Allowed values:
0: Disabled: Input denormal interrupt disable
1: Enabled: Input denormal interrupt enable

FPU_IE5

Bit 31: Inexact interrupt enable.

Allowed values:
0: Disabled: Inexact interrupt disable
1: Enabled: Inexact interrupt enable

RCR

CCM SRAM protection register

Offset: 0x4, reset: 0x0000, access: read-write

16/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PAGE15_WP
rw 		PAGE14_WP
rw 		PAGE13_WP
rw 		PAGE12_WP
rw 		PAGE11_WP
rw 		PAGE10_WP
rw 		PAGE9_WP
rw 		PAGE8_WP
rw 		PAGE7_WP
rw 		PAGE6_WP
rw 		PAGE5_WP
rw 		PAGE4_WP
rw 		PAGE3_WP
rw 		PAGE2_WP
rw 		PAGE1_WP
rw 		PAGE0_WP
rw
Toggle Fields.

PAGE0_WP

Bit 0: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE1_WP

Bit 1: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE2_WP

Bit 2: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE3_WP

Bit 3: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE4_WP

Bit 4: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE5_WP

Bit 5: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE6_WP

Bit 6: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE7_WP

Bit 7: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE8_WP

Bit 8: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE9_WP

Bit 9: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE10_WP

Bit 10: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE11_WP

Bit 11: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE12_WP

Bit 12: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE13_WP

Bit 13: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE14_WP

Bit 14: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE15_WP

Bit 15: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

EXTICR1

external interrupt configuration register 1

Offset: 0x8, reset: 0x0000, access: read-write

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EXTI3
rw 		EXTI2
rw 		EXTI1
rw 		EXTI0
rw
Toggle Fields.

EXTI0

Bits 0-3: EXTI 0 configuration bits.

Allowed values:
0: PA0: Select PA0 as the source input for the EXTI0 external interrupt
1: PB0: Select PB0 as the source input for the EXTI0 external interrupt
2: PC0: Select PC0 as the source input for the EXTI0 external interrupt
3: PD0: Select PD0 as the source input for the EXTI0 external interrupt
4: PE0: Select PE0 as the source input for the EXTI0 external interrupt
5: PF0: Select PF0 as the source input for the EXTI0 external interrupt
6: PG0: Select PG0 as the source input for the EXTI0 external interrupt
7: PH0: Select PH0 as the source input for the EXTI0 external interrupt

EXTI1

Bits 4-7: EXTI 1 configuration bits.

Allowed values:
0: PA1: Select PA1 as the source input for the EXTI1 external interrupt
1: PB1: Select PB1 as the source input for the EXTI1 external interrupt
2: PC1: Select PC1 as the source input for the EXTI1 external interrupt
3: PD1: Select PD1 as the source input for the EXTI1 external interrupt
4: PE1: Select PE1 as the source input for the EXTI1 external interrupt
5: PF1: Select PF1 as the source input for the EXTI1 external interrupt
6: PG1: Select PG1 as the source input for the EXTI1 external interrupt
7: PH1: Select PH1 as the source input for the EXTI1 external interrupt

EXTI2

Bits 8-11: EXTI 2 configuration bits.

Allowed values:
0: PA2: Select PA2 as the source input for the EXTI2 external interrupt
1: PB2: Select PB2 as the source input for the EXTI2 external interrupt
2: PC2: Select PC2 as the source input for the EXTI2 external interrupt
3: PD2: Select PD2 as the source input for the EXTI2 external interrupt
4: PE2: Select PE2 as the source input for the EXTI2 external interrupt
5: PF2: Select PF2 as the source input for the EXTI2 external interrupt
6: PG2: Select PG2 as the source input for the EXTI2 external interrupt
7: PH2: Select PH2 as the source input for the EXTI2 external interrupt

EXTI3

Bits 12-15: EXTI 3 configuration bits.

Allowed values:
0: PA3: Select PA3 as the source input for the EXTI3 external interrupt
1: PB3: Select PB3 as the source input for the EXTI3 external interrupt
2: PC3: Select PC3 as the source input for the EXTI3 external interrupt
3: PD3: Select PD3 as the source input for the EXTI3 external interrupt
4: PE3: Select PE3 as the source input for the EXTI3 external interrupt
5: PF3: Select PF3 as the source input for the EXTI3 external interrupt
6: PG3: Select PG3 as the source input for the EXTI3 external interrupt

EXTICR2

external interrupt configuration register 2

Offset: 0xC, reset: 0x0000, access: read-write

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EXTI7
rw 		EXTI6
rw 		EXTI5
rw 		EXTI4
rw
Toggle Fields.

EXTI4

Bits 0-3: EXTI 4 configuration bits.

Allowed values:
0: PA4: Select PA4 as the source input for the EXTI4 external interrupt
1: PB4: Select PB4 as the source input for the EXTI4 external interrupt
2: PC4: Select PC4 as the source input for the EXTI4 external interrupt
3: PD4: Select PD4 as the source input for the EXTI4 external interrupt
4: PE4: Select PE4 as the source input for the EXTI4 external interrupt
5: PF4: Select PF4 as the source input for the EXTI4 external interrupt
6: PG4: Select PG4 as the source input for the EXTI4 external interrupt

EXTI5

Bits 4-7: EXTI 5 configuration bits.

Allowed values:
0: PA5: Select PA5 as the source input for the EXTI5 external interrupt
1: PB5: Select PB5 as the source input for the EXTI5 external interrupt
2: PC5: Select PC5 as the source input for the EXTI5 external interrupt
3: PD5: Select PD5 as the source input for the EXTI5 external interrupt
4: PE5: Select PE5 as the source input for the EXTI5 external interrupt
5: PF5: Select PF5 as the source input for the EXTI5 external interrupt
6: PG5: Select PG5 as the source input for the EXTI5 external interrupt

EXTI6

Bits 8-11: EXTI 6 configuration bits.

Allowed values:
0: PA6: Select PA6 as the source input for the EXTI6 external interrupt
1: PB6: Select PB6 as the source input for the EXTI6 external interrupt
2: PC6: Select PC6 as the source input for the EXTI6 external interrupt
3: PD6: Select PD6 as the source input for the EXTI6 external interrupt
4: PE6: Select PE6 as the source input for the EXTI6 external interrupt
5: PF6: Select PF6 as the source input for the EXTI6 external interrupt
6: PG6: Select PG6 as the source input for the EXTI6 external interrupt

EXTI7

Bits 12-15: EXTI 7 configuration bits.

Allowed values:
0: PA7: Select PA7 as the source input for the EXTI7 external interrupt
1: PB7: Select PB7 as the source input for the EXTI7 external interrupt
2: PC7: Select PC7 as the source input for the EXTI7 external interrupt
3: PD7: Select PD7 as the source input for the EXTI7 external interrupt
4: PE7: Select PE7 as the source input for the EXTI7 external interrupt
5: PF7: Select PF7 as the source input for the EXTI7 external interrupt
6: PG7: Select PG7 as the source input for the EXTI7 external interrupt

EXTICR3

external interrupt configuration register 3

Offset: 0x10, reset: 0x0000, access: read-write

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EXTI11
rw 		EXTI10
rw 		EXTI9
rw 		EXTI8
rw
Toggle Fields.

EXTI8

Bits 0-3: EXTI 8 configuration bits.

Allowed values:
0: PA8: Select PA8 as the source input for the EXTI8 external interrupt
1: PB8: Select PB8 as the source input for the EXTI8 external interrupt
2: PC8: Select PC8 as the source input for the EXTI8 external interrupt
3: PD8: Select PD8 as the source input for the EXTI8 external interrupt
4: PE8: Select PE8 as the source input for the EXTI8 external interrupt
5: PF8: Select PF8 as the source input for the EXTI8 external interrupt
6: PG8: Select PG8 as the source input for the EXTI8 external interrupt

EXTI9

Bits 4-7: EXTI 9 configuration bits.

Allowed values:
0: PA9: Select PA9 as the source input for the EXTI9 external interrupt
1: PB9: Select PB9 as the source input for the EXTI9 external interrupt
2: PC9: Select PC9 as the source input for the EXTI9 external interrupt
3: PD9: Select PD9 as the source input for the EXTI9 external interrupt
4: PE9: Select PE9 as the source input for the EXTI9 external interrupt
5: PF9: Select PF9 as the source input for the EXTI9 external interrupt
6: PG9: Select PG9 as the source input for the EXTI9 external interrupt

EXTI10

Bits 8-11: EXTI 10 configuration bits.

Allowed values:
0: PA10: Select PA10 as the source input for the EXTI10 external interrupt
1: PB10: Select PB10 as the source input for the EXTI10 external interrupt
2: PC10: Select PC10 as the source input for the EXTI10 external interrupt
3: PD10: Select PD10 as the source input for the EXTI10 external interrupt
4: PE10: Select PE10 as the source input for the EXTI10 external interrupt
5: PF10: Select PF10 as the source input for the EXTI10 external interrupt
6: PG10: Select PG10 as the source input for the EXTI10 external interrupt

EXTI11

Bits 12-15: EXTI 11 configuration bits.

Allowed values:
0: PA11: Select PA11 as the source input for the EXTI11 external interrupt
1: PB11: Select PB11 as the source input for the EXTI11 external interrupt
2: PC11: Select PC11 as the source input for the EXTI11 external interrupt
3: PD11: Select PD11 as the source input for the EXTI11 external interrupt
4: PE11: Select PE11 as the source input for the EXTI11 external interrupt
5: PF11: Select PF11 as the source input for the EXTI11 external interrupt
6: PG11: Select PG11 as the source input for the EXTI11 external interrupt

EXTICR4

external interrupt configuration register 4

Offset: 0x14, reset: 0x0000, access: read-write

4/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EXTI15
rw 		EXTI14
rw 		EXTI13
rw 		EXTI12
rw
Toggle Fields.

EXTI12

Bits 0-3: EXTI 12 configuration bits.

Allowed values:
0: PA12: Select PA12 as the source input for the EXTI12 external interrupt
1: PB12: Select PB12 as the source input for the EXTI12 external interrupt
2: PC12: Select PC12 as the source input for the EXTI12 external interrupt
3: PD12: Select PD12 as the source input for the EXTI12 external interrupt
4: PE12: Select PE12 as the source input for the EXTI12 external interrupt
5: PF12: Select PF12 as the source input for the EXTI12 external interrupt
6: PG12: Select PG12 as the source input for the EXTI12 external interrupt

EXTI13

Bits 4-7: EXTI 13 configuration bits.

Allowed values:
0: PA13: Select PA13 as the source input for the EXTI13 external interrupt
1: PB13: Select PB13 as the source input for the EXTI13 external interrupt
2: PC13: Select PC13 as the source input for the EXTI13 external interrupt
3: PD13: Select PD13 as the source input for the EXTI13 external interrupt
4: PE13: Select PE13 as the source input for the EXTI13 external interrupt
5: PF13: Select PF13 as the source input for the EXTI13 external interrupt
6: PG13: Select PG13 as the source input for the EXTI13 external interrupt

EXTI14

Bits 8-11: EXTI 14 configuration bits.

Allowed values:
0: PA14: Select PA14 as the source input for the EXTI14 external interrupt
1: PB14: Select PB14 as the source input for the EXTI14 external interrupt
2: PC14: Select PC14 as the source input for the EXTI14 external interrupt
3: PD14: Select PD14 as the source input for the EXTI14 external interrupt
4: PE14: Select PE14 as the source input for the EXTI14 external interrupt
5: PF14: Select PF14 as the source input for the EXTI14 external interrupt
6: PG14: Select PG14 as the source input for the EXTI14 external interrupt

EXTI15

Bits 12-15: EXTI 15 configuration bits.

Allowed values:
0: PA15: Select PA15 as the source input for the EXTI15 external interrupt
1: PB15: Select PB15 as the source input for the EXTI15 external interrupt
2: PC15: Select PC15 as the source input for the EXTI15 external interrupt
3: PD15: Select PD15 as the source input for the EXTI15 external interrupt
4: PE15: Select PE15 as the source input for the EXTI15 external interrupt
5: PF15: Select PF15 as the source input for the EXTI15 external interrupt
6: PG15: Select PG15 as the source input for the EXTI15 external interrupt

CFGR2

configuration register 2

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SRAM_PEF
rw 		BYP_ADDR_PAR
rw 		PVD_LOCK
rw 		SRAM_PARITY_LOCK
rw 		LOCKUP_LOCK
rw
Toggle Fields.

LOCKUP_LOCK

Bit 0: Cortex-M0 LOCKUP bit enable bit.

Allowed values:
0: Disconnected: Cortex-M4F LOCKUP output disconnected from TIM1/15/16/17 Break input
1: Connected: Cortex-M4F LOCKUP output connected to TIM1/15/16/17 Break input

SRAM_PARITY_LOCK

Bit 1: SRAM parity lock bit.

Allowed values:
0: Disconnected: SRAM parity error disconnected from TIM1/15/16/17 Break input
1: Connected: SRAM parity error connected to TIM1/15/16/17 Break input

PVD_LOCK

Bit 2: PVD lock enable bit.

Allowed values:
0: Disconnected: PVD interrupt disconnected from TIM15/16/17 Break input
1: Connected: PVD interrupt connected to TIM15/16/17 Break input

BYP_ADDR_PAR

Bit 4: Bypass address bit 29 in parity calculation.

Allowed values:
0: NoBypass: The ramload operation is performed taking into consideration bit 29 of the address when the parity is calculated
1: Bypass: The ramload operation is performed without taking into consideration bit 29 of the address when the parity is calculated

SRAM_PEF

Bit 8: SRAM parity flag.

Allowed values:
0: NoParityError: No SRAM parity error detected
1: ParityErrorDetected: SRAM parity error detected

CFGR3

configuration register 3

Offset: 0x50, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ADC2_DMA_RMP
rw 		I2C1_TX_DMA_RMP
rw 		I2C1_RX_DMA_RMP
rw 		SPI1_TX_DMA_RMP
rw 		SPI1_RX_DMA_RMP
rw
Toggle Fields.

SPI1_RX_DMA_RMP

Bits 0-1: SPI1_RX DMA remapping bit.

Allowed values:
0: MapDma1Ch3: SPI1_RX mapped on DMA1 CH2
1: MapDma1Ch5: SPI1_RX mapped on DMA1 CH4
2: MapDma1Ch7: SPI1_RX mapped on DMA1 CH6

SPI1_TX_DMA_RMP

Bits 2-3: SPI1_TX DMA remapping bit.

Allowed values:
0: MapDma1Ch3: SPI1_TX mapped on DMA1 CH3
1: MapDma1Ch5: SPI1_TX mapped on DMA1 CH5
2: MapDma1Ch7: SPI1_TX mapped on DMA1 CH7

I2C1_RX_DMA_RMP

Bits 4-5: I2C1_RX DMA remapping bit.

Allowed values:
0: MapDma1Ch7: I2C1_RX mapped on DMA1 CH7
1: MapDma1Ch3: I2C1_RX mapped on DMA1 CH3
2: MapDma1Ch5: I2C1_RX mapped on DMA1 CH5

I2C1_TX_DMA_RMP

Bits 6-7: I2C1_TX DMA remapping bit.

Allowed values:
0: MapDma1Ch6: I2C1_TX mapped on DMA1 CH6
1: MapDma1Ch2: I2C1_TX mapped on DMA1 CH2
2: MapDma1Ch4: I2C1_TX mapped on DMA1 CH4

ADC2_DMA_RMP

Bits 8-9: ADC2 DMA remapping bit.

Allowed values:
0: MapDma2: ADC2 mapped on DMA2
3: MapDma1Ch2: ADC2 mapped on DMA1 channel 2
4: MapDma1Ch4: DC2 mapped on DMA1 channel 4

CFGR4

configuration register 4

Offset: 0x72, reset: 0, access: read-write

14/14 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ADC34_JEXT14_RMP
rw 		ADC34_JEXT11_RMP
rw 		ADC34_JEXT5_RMP
rw 		ADC34_EXT15_RMP
rw 		ADC34_EXT6_RMP
rw 		ADC34_EXT5_RMP
rw 		ADC12_JEXT13_RMP
rw 		ADC12_JEXT6_RMP
rw 		ADC12_JEXT3_RMP
rw 		ADC12_EXT15_RMP
rw 		ADC12_EXT13_RMP
rw 		ADC12_EXT5_RMP
rw 		ADC12_EXT3_RMP
rw 		ADC12_EXT2_RMP
rw
Toggle Fields.

ADC12_EXT2_RMP

Bit 0: Controls the Input trigger of ADC12 regular channel EXT2.

Allowed values:
0: Tim1: Trigger source is TIM3_CC3
1: Tim20: rigger source is TIM20_TRGO

ADC12_EXT3_RMP

Bit 1: Controls the Input trigger of ADC12 regular channel EXT3.

Allowed values:
0: Tim2: Trigger source is TIM2_CC2
1: Tim20: rigger source is TIM20_TRGO2

ADC12_EXT5_RMP

Bit 2: Controls the Input trigger of ADC12 regular channel EXT5.

Allowed values:
0: Tim4: Trigger source is TIM4_CC4
1: Tim20: Trigger source is TIM20_CC1

ADC12_EXT13_RMP

Bit 3: Controls the Input trigger of ADC12 regular channel EXT13.

Allowed values:
0: Tim6: Trigger source is TIM6_TRGO
1: Tim20: Trigger source is TIM20_CC2

ADC12_EXT15_RMP

Bit 4: Controls the Input trigger of ADC12 regular channel EXT15.

Allowed values:
0: Tim3: Trigger source is TIM3_CC4
1: Tim20: Trigger source is TIM20_CC3

ADC12_JEXT3_RMP

Bit 5: Controls the Input trigger of ADC12 injected channel JEXT3.

Allowed values:
0: Tim2: Trigger source is TIM2_CC1
1: Tim20: Trigger source is TIM20_TRGO

ADC12_JEXT6_RMP

Bit 6: Controls the Input trigger of ADC12 injected channel JEXT6.

Allowed values:
0: Exti15: Trigger source is EXTI line 15
1: Tim20: Trigger source is TIM20_TRGO2

ADC12_JEXT13_RMP

Bit 7: Controls the Input trigger of ADC12 injected channel JEXT13.

Allowed values:
0: Tim3: Trigger source is TIM3_CC1
1: Tim20: Trigger source is TIM20_CC4

ADC34_EXT5_RMP

Bit 8: Controls the Input trigger of ADC34 regular channel EXT5.

Allowed values:
0: Exti2: Trigger source is EXTI line 2 when reset at 0
1: Tim20: Trigger source is TIM20_TRGO

ADC34_EXT6_RMP

Bit 9: Controls the Input trigger of ADC34 regular channel EXT6.

Allowed values:
0: Tim4: Trigger source is TIM4_CC1
1: Tim20: Trigger source is TIM20_TRGO2

ADC34_EXT15_RMP

Bit 10: Controls the Input trigger of ADC34 regular channel EXT15.

Allowed values:
0: Tim2: Trigger source is TIM2_CC1
1: Tim20: Trigger source is TIM20_CC1

ADC34_JEXT5_RMP

Bit 11: Controls the Input trigger of ADC34 injected channel JEXT5.

Allowed values:
0: Tim4: Trigger source is TIM4_CC3
1: Tim20: Trigger source is TIM20_TRGO

ADC34_JEXT11_RMP

Bit 12: Controls the Input trigger of ADC34 injected channel JEXT11.

Allowed values:
0: Tim1: Trigger source is TIM1_CC3
1: Tim20: Trigger source is TIM20_TRGO2

ADC34_JEXT14_RMP

Bit 13: Controls the Input trigger of ADC34 injected channel JEXT14.

Allowed values:
0: Tim7: Trigger source is TIM7_TRGO
1: Tim20: Trigger source is TIM20_CC2

TIM1

0x40012C00: Advanced timer

78/165 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UIFREMAP
rw 		CKD
rw 		ARPE
rw 		CMS
rw 		DIR
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/15 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MMS2
rw 		OIS6
rw 		OIS5
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OIS4
rw 		OIS3N
rw 		OIS3
rw 		OIS2N
rw 		OIS2
rw 		OIS1N
rw 		OIS1
rw 		TI1S
rw 		MMS
rw 		CCDS
rw 		CCUS
rw 		CCPC
rw
Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

OIS2

Bit 10: Output Idle state 2.

OIS2N

Bit 11: Output Idle state 2.

OIS3

Bit 12: Output Idle state 3.

OIS3N

Bit 13: Output Idle state 3.

OIS4

Bit 14: Output Idle state 4.

OIS5

Bit 16: Output Idle state 5.

OIS6

Bit 18: Output Idle state 6.

MMS2

Bits 20-23: Master mode selection 2.

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMS3
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ETP
rw 		ECE
rw 		ETPS
rw 		ETF
rw 		MSM
rw 		TS
rw 		OCCS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

SMS3

Bit 16: Slave mode selection bit 3.

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/15 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		COMDE
rw 		CC4DE
rw 		CC3DE
rw 		CC2DE
rw 		CC1DE
rw 		UDE
rw 		BIE
rw 		TIE
rw 		COMIE
rw 		CC4IE
rw 		CC3IE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/15 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
C6IF
rw 		C5IF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4OF
rw 		CC3OF
rw 		CC2OF
rw 		CC1OF
rw 		B2IF
rw 		BIF
rw 		TIF
rw 		COMIF
rw 		CC4IF
rw 		CC3IF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

BIF

Bit 7: Break interrupt flag.

B2IF

Bit 8: Break 2 interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

C5IF

Bit 16: Capture/Compare 5 interrupt flag.

C6IF

Bit 17: Capture/Compare 6 interrupt flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
B2G
w 		BG
w 		TG
w 		COMG
w 		CC4G
w 		CC3G
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC2G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC3G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC4G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

BG

Bit 7: Break generation.

B2G

Bit 8: Break 2 generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC2S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI2: CC2 channel is configured as input, IC2 is mapped on TI2
2: TI1: CC2 channel is configured as input, IC2 is mapped on TI1
3: TRC: CC2 channel is configured as input, IC2 is mapped on TRC

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC4F
rw 		IC4PSC
rw 		CC4S
rw 		IC3F
rw 		IC3PSC
rw 		CC3S
rw
Toggle Fields.

CC3S

Bits 0-1: Capture/compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI4: CC4 channel is configured as input, IC4 is mapped on TI4
2: TI3: CC4 channel is configured as input, IC4 is mapped on TI3
3: TRC: CC4 channel is configured as input, IC4 is mapped on TRC

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CC6P
rw 		CC6E
rw 		CC5P
rw 		CC5E
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4NP
rw 		CC4P
rw 		CC4E
rw 		CC3NP
rw 		CC3NE
rw 		CC3P
rw 		CC3E
rw 		CC2NP
rw 		CC2NE
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1NE
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NE

Bit 6: Capture/Compare 2 complementary output enable.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NE

Bit 10: Capture/Compare 3 complementary output enable.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 4 output Polarity.

CC5E

Bit 16: Capture/Compare 5 output enable.

CC5P

Bit 17: Capture/Compare 5 output Polarity.

CC6E

Bit 20: Capture/Compare 6 output enable.

CC6P

Bit 21: Capture/Compare 6 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: Unspecified

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
UIFCPY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

Allowed values: 0-65535

UIFCPY

Bit 31: UIF copy.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0-65535

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
REP
rw
Toggle Fields.

REP

Bits 0-15: Repetition counter value.

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

Allowed values: 0-65535

BDTR

break and dead-time register

Offset: 0x44, reset: 0x00000000, access: read-write

3/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BK2P
rw 		BK2E
rw 		BK2F
rw 		BKF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MOE
rw 		AOE
rw 		BKP
rw 		BKE
rw 		OSSR
rw 		OSSI
rw 		LOCK
rw 		DTG
rw
Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are forced to idle level

OSSR

Bit 11: Off-state selection for Run mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are enabled with their inactive level

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

Allowed values:
0: DisabledIdle: OC/OCN are disabled or forced idle depending on OSSI
1: Enabled: OC/OCN are enabled if CCxE/CCxNE are set

BKF

Bits 16-19: Break filter.

BK2F

Bits 20-23: Break 2 filter.

BK2E

Bit 24: Break 2 enable.

BK2P

Bit 25: Break 2 polarity.

DCR

DMA control register

Offset: 0x48, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

CCMR3_Output

capture/compare mode register 3 (output mode)

Offset: 0x54, reset: 0x00000000, access: read-write

0/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OC6M_3
rw 		OC5M_3
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OC6CE
rw 		OC6M
rw 		OC6PE
rw 		OC6FE
rw 		OC5CE
rw 		OC5M
rw 		OC5PE
rw 		OC5FE
rw
Toggle Fields.

OC5FE

Bit 2: Output compare 5 fast enable.

OC5PE

Bit 3: Output compare 5 preload enable.

OC5M

Bits 4-6: Output compare 5 mode.

OC5CE

Bit 7: Output compare 5 clear enable.

OC6FE

Bit 10: Output compare 6 fast enable.

OC6PE

Bit 11: Output compare 6 preload enable.

OC6M

Bits 12-14: Output compare 6 mode.

OC6CE

Bit 15: Output compare 6 clear enable.

OC5M_3

Bit 16: Outout Compare 5 mode bit 3.

OC6M_3

Bit 24: Outout Compare 6 mode bit 3.

CCR5

capture/compare register 5

Offset: 0x58, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
GC5C3
rw 		GC5C2
rw 		GC5C1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 5 value.

GC5C1

Bit 29: Group Channel 5 and Channel 1.

GC5C2

Bit 30: Group Channel 5 and Channel 2.

GC5C3

Bit 31: Group Channel 5 and Channel 3.

CCR6

capture/compare register 6

Offset: 0x5C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 6 value.

OR

option registers

Offset: 0x60, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TIM1_ETR_ADC4_RMP
rw 		TIM1_ETR_ADC1_RMP
rw
Toggle Fields.

TIM1_ETR_ADC1_RMP

Bits 0-1: TIM1_ETR_ADC1 remapping capability.

TIM1_ETR_ADC4_RMP

Bits 2-3: TIM1_ETR_ADC4 remapping capability.

TIM12

0x40001800: General purpose timers

10/47 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MSM
rw 		TS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

TS

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

1/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TIE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC2OF
rw 		CC1OF
rw 		TIF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TG
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

CC2G

Bit 2: Capture/compare 2 generation.

TG

Bit 6: Trigger generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-6: Input capture 1 filter.

CC2S

Bits 8-9: Capture/Compare 2 selection.

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC2NP
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

TIM13

0x40001C00: General purpose timers

9/26 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

1/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1OF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

CCMR1_Input

capture/compare mode register (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1NP
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

TIM14

0x40002000: General purpose timers

9/26 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

1/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1OF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

CCMR1_Input

capture/compare mode register (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1NP
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

TIM15

0x40014000: General purpose timers

9/78 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OIS2
rw 		OIS1N
rw 		OIS1
rw 		MMS
rw 		CCDS
rw 		CCUS
rw 		CCPC
rw
Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

MMS

Bits 4-6: Master mode selection.

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

OIS2

Bit 10: Output Idle state 2.

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MSM
rw 		TS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

TS

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

1/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC2DE
rw 		CC1DE
rw 		UDE
rw 		BIE
rw 		TIE
rw 		COMIE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC2OF
rw 		CC1OF
rw 		BIF
rw 		TIF
rw 		COMIF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BG
w 		TG
w 		COMG
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

CC2G

Bit 2: Capture/compare 2 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CC2S

Bits 8-9: Capture/Compare 2 selection.

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC2NP
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1NE
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
REP
rw
Toggle Fields.

REP

Bits 0-7: Repetition counter value.

CCR1

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR1
rw
Toggle Fields.

CCR1

Bits 0-15: Capture/Compare 1 value.

CCR2

capture/compare register 2

Offset: 0x38, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR2
rw
Toggle Fields.

CCR2

Bits 0-15: Capture/Compare 2 value.

BDTR

break and dead-time register

Offset: 0x44, reset: 0x0000, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MOE
rw 		AOE
rw 		BKP
rw 		BKE
rw 		OSSR
rw 		OSSI
rw 		LOCK
rw 		DTG
rw
Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM16

0x40014400: General-purpose-timers

19/57 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: NotStopped: Not stopped at update event
1: Stopped: Counter stops counting at next update event

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OIS1N
rw 		OIS1
rw 		CCDS
rw 		CCUS
rw 		CCPC
rw
Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

Allowed values:
0: NotPreloaded: CCxE, CCxNE and OCxM bits are not preloaded
1: Preloaded: CCxE, CCxNE and OCxM bits are preloaded

CCUS

Bit 2: Capture/compare control update selection.

Allowed values:
0: Default: Capture/compare are updated only by setting the COMG bit
1: WithRisingEdge: Capture/compare are updated by setting the COMG bit or when an rising edge occurs on TRGI

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

OIS1

Bit 8: Output Idle state 1.

Allowed values:
0: Low: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: High: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0

OIS1N

Bit 9: Output Idle state 1.

Allowed values:
0: Low: OC1N=0 after a dead-time when MOE=0
1: High: OC1N=1 after a dead-time when MOE=0

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

5/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC1DE
rw 		UDE
rw 		BIE
rw 		TIE
rw 		COMIE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CC1 interrupt disabled
1: Enabled: CC1 interrupt enabled

COMIE

Bit 5: COM interrupt enable.

Allowed values:
0: Disabled: COM interrupt disabled
1: Enabled: COM interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

Allowed values:
0: Disabled: Break interrupt disabled
1: Enabled: Break interrupt enabled

UDE

Bit 8: Update DMA request enable.

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CC1 DMA request disabled
1: Enabled: CC1 DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1OF
rw 		BIF
rw 		TIF
rw 		COMIF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BG
w 		TG
w 		COMG
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1NP
rw 		CC1NE
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
REP
rw
Toggle Fields.

REP

Bits 0-7: Repetition counter value.

CCR1

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR1
rw
Toggle Fields.

CCR1

Bits 0-15: Capture/Compare 1 value.

BDTR

break and dead-time register

Offset: 0x44, reset: 0x0000, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MOE
rw 		AOE
rw 		BKP
rw 		BKE
rw 		OSSR
rw 		OSSI
rw 		LOCK
rw 		DTG
rw
Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM17

0x40014800: General-purpose-timers

19/57 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: NotStopped: Not stopped at update event
1: Stopped: Counter stops counting at next update event

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OIS1N
rw 		OIS1
rw 		CCDS
rw 		CCUS
rw 		CCPC
rw
Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

Allowed values:
0: NotPreloaded: CCxE, CCxNE and OCxM bits are not preloaded
1: Preloaded: CCxE, CCxNE and OCxM bits are preloaded

CCUS

Bit 2: Capture/compare control update selection.

Allowed values:
0: Default: Capture/compare are updated only by setting the COMG bit
1: WithRisingEdge: Capture/compare are updated by setting the COMG bit or when an rising edge occurs on TRGI

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

OIS1

Bit 8: Output Idle state 1.

Allowed values:
0: Low: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: High: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0

OIS1N

Bit 9: Output Idle state 1.

Allowed values:
0: Low: OC1N=0 after a dead-time when MOE=0
1: High: OC1N=1 after a dead-time when MOE=0

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

5/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC1DE
rw 		UDE
rw 		BIE
rw 		TIE
rw 		COMIE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CC1 interrupt disabled
1: Enabled: CC1 interrupt enabled

COMIE

Bit 5: COM interrupt enable.

Allowed values:
0: Disabled: COM interrupt disabled
1: Enabled: COM interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

Allowed values:
0: Disabled: Break interrupt disabled
1: Enabled: Break interrupt enabled

UDE

Bit 8: Update DMA request enable.

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CC1 DMA request disabled
1: Enabled: CC1 DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1OF
rw 		BIF
rw 		TIF
rw 		COMIF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BG
w 		TG
w 		COMG
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1NP
rw 		CC1NE
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
REP
rw
Toggle Fields.

REP

Bits 0-7: Repetition counter value.

CCR1

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR1
rw
Toggle Fields.

CCR1

Bits 0-15: Capture/Compare 1 value.

BDTR

break and dead-time register

Offset: 0x44, reset: 0x0000, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MOE
rw 		AOE
rw 		BKP
rw 		BKE
rw 		OSSR
rw 		OSSI
rw 		LOCK
rw 		DTG
rw
Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM18

0x40009C00: Basic timers

13/13 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARPE
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MMS
rw
Toggle Fields.

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: Use UG bit from TIMx_EGR register
1: Enable: Use CNT bit from TIMx_CEN register
2: Update: Use the update event

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UDE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: Low counter value.

Allowed values: 0-65536

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Low Auto-reload value.

Allowed values: 0-65536

TIM19

0x40015C00: General purpose timer

74/97 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		CMS
rw 		DIR
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TI1S
rw 		MMS
rw 		CCDS
rw
Toggle Fields.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ETP
rw 		ECE
rw 		ETPS
rw 		ETF
rw 		MSM
rw 		TS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC4DE
rw 		CC3DE
rw 		CC2DE
rw 		CC1DE
rw 		UDE
rw 		TIE
rw 		CC4IE
rw 		CC3IE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4OF
rw 		CC3OF
rw 		CC2OF
rw 		CC1OF
rw 		TIF
rw 		CC4IF
rw 		CC3IF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TG
w 		CC4G
w 		CC3G
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC2G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC3G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC4G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC2S

Bits 8-9: Capture/compare 2 selection.

Allowed values:
1: TI2: CC2 channel is configured as input, IC2 is mapped on TI2
2: TI1: CC2 channel is configured as input, IC2 is mapped on TI1
3: TRC: CC2 channel is configured as input, IC2 is mapped on TRC

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC4F
rw 		IC4PSC
rw 		CC4S
rw 		IC3F
rw 		IC3PSC
rw 		CC3S
rw
Toggle Fields.

CC3S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI4: CC4 channel is configured as input, IC4 is mapped on TI4
2: TI3: CC4 channel is configured as input, IC4 is mapped on TI3
3: TRC: CC4 channel is configured as input, IC4 is mapped on TRC

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4NP
rw 		CC4P
rw 		CC4E
rw 		CC3NP
rw 		CC3P
rw 		CC3E
rw 		CC2NP
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 3 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

Allowed values: 0-65535

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0-65535

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

Allowed values: 0-65535

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM2

0x40000000: General purpose timer

74/98 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		CMS
rw 		DIR
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TI1S
rw 		MMS
rw 		CCDS
rw
Toggle Fields.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ETP
rw 		ECE
rw 		ETPS
rw 		ETF
rw 		MSM
rw 		TS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC4DE
rw 		CC3DE
rw 		CC2DE
rw 		CC1DE
rw 		UDE
rw 		TIE
rw 		CC4IE
rw 		CC3IE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4OF
rw 		CC3OF
rw 		CC2OF
rw 		CC1OF
rw 		TIF
rw 		CC4IF
rw 		CC3IF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TG
w 		CC4G
w 		CC3G
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC2G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC3G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC4G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC2S

Bits 8-9: Capture/compare 2 selection.

Allowed values:
1: TI2: CC2 channel is configured as input, IC2 is mapped on TI2
2: TI1: CC2 channel is configured as input, IC2 is mapped on TI1
3: TRC: CC2 channel is configured as input, IC2 is mapped on TRC

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC4F
rw 		IC4PSC
rw 		CC4S
rw 		IC3F
rw 		IC3PSC
rw 		CC3S
rw
Toggle Fields.

CC3S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI4: CC4 channel is configured as input, IC4 is mapped on TI4
2: TI3: CC4 channel is configured as input, IC4 is mapped on TI3
3: TRC: CC4 channel is configured as input, IC4 is mapped on TRC

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4NP
rw 		CC4P
rw 		CC4E
rw 		CC3NP
rw 		CC3P
rw 		CC3E
rw 		CC2NP
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 3 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CNT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-31: Low counter value.

Allowed values: 0-4294967295

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ARR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-31: Low Auto-reload value.

Allowed values: 0-4294967295

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CCR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-31: Low Capture/Compare 1 value.

Allowed values: 0-4294967295

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

OR

option register

Offset: 0x50, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ITR1_RMP
rw
Toggle Fields.

ITR1_RMP

Bits 10-11: Internal trigger 1 remap.

TIM20

0x40015000: General-purpose-timers

19/57 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: NotStopped: Not stopped at update event
1: Stopped: Counter stops counting at next update event

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OIS1N
rw 		OIS1
rw 		CCDS
rw 		CCUS
rw 		CCPC
rw
Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

Allowed values:
0: NotPreloaded: CCxE, CCxNE and OCxM bits are not preloaded
1: Preloaded: CCxE, CCxNE and OCxM bits are preloaded

CCUS

Bit 2: Capture/compare control update selection.

Allowed values:
0: Default: Capture/compare are updated only by setting the COMG bit
1: WithRisingEdge: Capture/compare are updated by setting the COMG bit or when an rising edge occurs on TRGI

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

OIS1

Bit 8: Output Idle state 1.

Allowed values:
0: Low: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: High: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0

OIS1N

Bit 9: Output Idle state 1.

Allowed values:
0: Low: OC1N=0 after a dead-time when MOE=0
1: High: OC1N=1 after a dead-time when MOE=0

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

5/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC1DE
rw 		UDE
rw 		BIE
rw 		TIE
rw 		COMIE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CC1 interrupt disabled
1: Enabled: CC1 interrupt enabled

COMIE

Bit 5: COM interrupt enable.

Allowed values:
0: Disabled: COM interrupt disabled
1: Enabled: COM interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

Allowed values:
0: Disabled: Break interrupt disabled
1: Enabled: Break interrupt enabled

UDE

Bit 8: Update DMA request enable.

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CC1 DMA request disabled
1: Enabled: CC1 DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1OF
rw 		BIF
rw 		TIF
rw 		COMIF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BG
w 		TG
w 		COMG
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC1NP
rw 		CC1NE
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
REP
rw
Toggle Fields.

REP

Bits 0-7: Repetition counter value.

CCR1

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR1
rw
Toggle Fields.

CCR1

Bits 0-15: Capture/Compare 1 value.

BDTR

break and dead-time register

Offset: 0x44, reset: 0x0000, access: read-write

0/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MOE
rw 		AOE
rw 		BKP
rw 		BKE
rw 		OSSR
rw 		OSSI
rw 		LOCK
rw 		DTG
rw
Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM3

0x40000400: General purpose timer

74/97 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		CMS
rw 		DIR
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TI1S
rw 		MMS
rw 		CCDS
rw
Toggle Fields.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ETP
rw 		ECE
rw 		ETPS
rw 		ETF
rw 		MSM
rw 		TS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC4DE
rw 		CC3DE
rw 		CC2DE
rw 		CC1DE
rw 		UDE
rw 		TIE
rw 		CC4IE
rw 		CC3IE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4OF
rw 		CC3OF
rw 		CC2OF
rw 		CC1OF
rw 		TIF
rw 		CC4IF
rw 		CC3IF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TG
w 		CC4G
w 		CC3G
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC2G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC3G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC4G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC2S

Bits 8-9: Capture/compare 2 selection.

Allowed values:
1: TI2: CC2 channel is configured as input, IC2 is mapped on TI2
2: TI1: CC2 channel is configured as input, IC2 is mapped on TI1
3: TRC: CC2 channel is configured as input, IC2 is mapped on TRC

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC4F
rw 		IC4PSC
rw 		CC4S
rw 		IC3F
rw 		IC3PSC
rw 		CC3S
rw
Toggle Fields.

CC3S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI4: CC4 channel is configured as input, IC4 is mapped on TI4
2: TI3: CC4 channel is configured as input, IC4 is mapped on TI3
3: TRC: CC4 channel is configured as input, IC4 is mapped on TRC

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4NP
rw 		CC4P
rw 		CC4E
rw 		CC3NP
rw 		CC3P
rw 		CC3E
rw 		CC2NP
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 3 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

Allowed values: 0-65535

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0-65535

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

Allowed values: 0-65535

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM4

0x40000800: General purpose timer

74/97 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		CMS
rw 		DIR
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TI1S
rw 		MMS
rw 		CCDS
rw
Toggle Fields.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ETP
rw 		ECE
rw 		ETPS
rw 		ETF
rw 		MSM
rw 		TS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC4DE
rw 		CC3DE
rw 		CC2DE
rw 		CC1DE
rw 		UDE
rw 		TIE
rw 		CC4IE
rw 		CC3IE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4OF
rw 		CC3OF
rw 		CC2OF
rw 		CC1OF
rw 		TIF
rw 		CC4IF
rw 		CC3IF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TG
w 		CC4G
w 		CC3G
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC2G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC3G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC4G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC2S

Bits 8-9: Capture/compare 2 selection.

Allowed values:
1: TI2: CC2 channel is configured as input, IC2 is mapped on TI2
2: TI1: CC2 channel is configured as input, IC2 is mapped on TI1
3: TRC: CC2 channel is configured as input, IC2 is mapped on TRC

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC4F
rw 		IC4PSC
rw 		CC4S
rw 		IC3F
rw 		IC3PSC
rw 		CC3S
rw
Toggle Fields.

CC3S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI4: CC4 channel is configured as input, IC4 is mapped on TI4
2: TI3: CC4 channel is configured as input, IC4 is mapped on TI3
3: TRC: CC4 channel is configured as input, IC4 is mapped on TRC

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4NP
rw 		CC4P
rw 		CC4E
rw 		CC3NP
rw 		CC3P
rw 		CC3E
rw 		CC2NP
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 3 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

Allowed values: 0-65535

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0-65535

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

Allowed values: 0-65535

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM5

0x40000C00: General purpose timer

74/98 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CKD
rw 		ARPE
rw 		CMS
rw 		DIR
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TI1S
rw 		MMS
rw 		CCDS
rw
Toggle Fields.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/7 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ETP
rw 		ECE
rw 		ETPS
rw 		ETF
rw 		MSM
rw 		TS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		CC4DE
rw 		CC3DE
rw 		CC2DE
rw 		CC1DE
rw 		UDE
rw 		TIE
rw 		CC4IE
rw 		CC3IE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4OF
rw 		CC3OF
rw 		CC2OF
rw 		CC1OF
rw 		TIF
rw 		CC4IF
rw 		CC3IF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TG
w 		CC4G
w 		CC3G
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC2G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC3G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC4G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC2S

Bits 8-9: Capture/compare 2 selection.

Allowed values:
1: TI2: CC2 channel is configured as input, IC2 is mapped on TI2
2: TI1: CC2 channel is configured as input, IC2 is mapped on TI1
3: TRC: CC2 channel is configured as input, IC2 is mapped on TRC

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC4F
rw 		IC4PSC
rw 		CC4S
rw 		IC3F
rw 		IC3PSC
rw 		CC3S
rw
Toggle Fields.

CC3S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI4: CC4 channel is configured as input, IC4 is mapped on TI4
2: TI3: CC4 channel is configured as input, IC4 is mapped on TI3
3: TRC: CC4 channel is configured as input, IC4 is mapped on TRC

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4NP
rw 		CC4P
rw 		CC4E
rw 		CC3NP
rw 		CC3P
rw 		CC3E
rw 		CC2NP
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 3 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CNT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-31: Low counter value.

Allowed values: 0-4294967295

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ARR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-31: Low Auto-reload value.

Allowed values: 0-4294967295

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CCR
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-31: Low Capture/Compare 1 value.

Allowed values: 0-4294967295

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

OR

option register

Offset: 0x50, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IT4_RMP
rw
Toggle Fields.

IT4_RMP

Bits 6-7: Timer Input 4 remap.

TIM6

0x40001000: Basic timers

13/13 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARPE
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MMS
rw
Toggle Fields.

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: Use UG bit from TIMx_EGR register
1: Enable: Use CNT bit from TIMx_CEN register
2: Update: Use the update event

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UDE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: Low counter value.

Allowed values: 0-65536

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Low Auto-reload value.

Allowed values: 0-65536

TIM7

0x40001400: Basic timers

13/13 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARPE
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MMS
rw
Toggle Fields.

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: Use UG bit from TIMx_EGR register
1: Enable: Use CNT bit from TIMx_CEN register
2: Update: Use the update event

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UDE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: Low counter value.

Allowed values: 0-65536

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Low Auto-reload value.

Allowed values: 0-65536

TIM8

0x40013400: Advanced timer

78/165 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
UIFREMAP
rw 		CKD
rw 		ARPE
rw 		CMS
rw 		DIR
rw 		OPM
rw 		URS
rw 		UDIS
rw 		CEN
rw
Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/15 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
MMS2
rw 		OIS6
rw 		OIS5
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OIS4
rw 		OIS3N
rw 		OIS3
rw 		OIS2N
rw 		OIS2
rw 		OIS1N
rw 		OIS1
rw 		TI1S
rw 		MMS
rw 		CCDS
rw 		CCUS
rw 		CCPC
rw
Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

OIS2

Bit 10: Output Idle state 2.

OIS2N

Bit 11: Output Idle state 2.

OIS3

Bit 12: Output Idle state 3.

OIS3N

Bit 13: Output Idle state 3.

OIS4

Bit 14: Output Idle state 4.

OIS5

Bit 16: Output Idle state 5.

OIS6

Bit 18: Output Idle state 6.

MMS2

Bits 20-23: Master mode selection 2.

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
SMS3
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ETP
rw 		ECE
rw 		ETPS
rw 		ETF
rw 		MSM
rw 		TS
rw 		OCCS
rw 		SMS
rw
Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

SMS3

Bit 16: Slave mode selection bit 3.

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/15 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDE
rw 		COMDE
rw 		CC4DE
rw 		CC3DE
rw 		CC2DE
rw 		CC1DE
rw 		UDE
rw 		BIE
rw 		TIE
rw 		COMIE
rw 		CC4IE
rw 		CC3IE
rw 		CC2IE
rw 		CC1IE
rw 		UIE
rw
Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/15 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
C6IF
rw 		C5IF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4OF
rw 		CC3OF
rw 		CC2OF
rw 		CC1OF
rw 		B2IF
rw 		BIF
rw 		TIF
rw 		COMIF
rw 		CC4IF
rw 		CC3IF
rw 		CC2IF
rw 		CC1IF
rw 		UIF
rw
Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

BIF

Bit 7: Break interrupt flag.

B2IF

Bit 8: Break 2 interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

C5IF

Bit 16: Capture/Compare 5 interrupt flag.

C6IF

Bit 17: Capture/Compare 6 interrupt flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/9 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
B2G
w 		BG
w 		TG
w 		COMG
w 		CC4G
w 		CC3G
w 		CC2G
w 		CC1G
w 		UG
w
Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the reigsters.

CC1G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC2G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC3G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC4G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

BG

Bit 7: Break generation.

B2G

Bit 8: Break 2 generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC2F
rw 		IC2PSC
rw 		CC2S
rw 		IC1F
rw 		IC1PSC
rw 		CC1S
rw
Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC2S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI2: CC2 channel is configured as input, IC2 is mapped on TI2
2: TI1: CC2 channel is configured as input, IC2 is mapped on TI1
3: TRC: CC2 channel is configured as input, IC2 is mapped on TRC

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
IC4F
rw 		IC4PSC
rw 		CC4S
rw 		IC3F
rw 		IC3PSC
rw 		CC3S
rw
Toggle Fields.

CC3S

Bits 0-1: Capture/compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI4: CC4 channel is configured as input, IC4 is mapped on TI4
2: TI3: CC4 channel is configured as input, IC4 is mapped on TI3
3: TRC: CC4 channel is configured as input, IC4 is mapped on TRC

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CC6P
rw 		CC6E
rw 		CC5P
rw 		CC5E
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CC4NP
rw 		CC4P
rw 		CC4E
rw 		CC3NP
rw 		CC3NE
rw 		CC3P
rw 		CC3E
rw 		CC2NP
rw 		CC2NE
rw 		CC2P
rw 		CC2E
rw 		CC1NP
rw 		CC1NE
rw 		CC1P
rw 		CC1E
rw
Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NE

Bit 6: Capture/Compare 2 complementary output enable.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NE

Bit 10: Capture/Compare 3 complementary output enable.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 4 output Polarity.

CC5E

Bit 16: Capture/Compare 5 output enable.

CC5P

Bit 17: Capture/Compare 5 output Polarity.

CC6E

Bit 20: Capture/Compare 6 output enable.

CC6P

Bit 21: Capture/Compare 6 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: Unspecified

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
UIFCPY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
rw
Toggle Fields.

CNT

Bits 0-15: counter value.

Allowed values: 0-65535

UIFCPY

Bit 31: UIF copy.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
PSC
rw
Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ARR
rw
Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0-65535

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
REP
rw
Toggle Fields.

REP

Bits 0-15: Repetition counter value.

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

Allowed values: 0-65535

BDTR

break and dead-time register

Offset: 0x44, reset: 0x00000000, access: read-write

3/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BK2P
rw 		BK2E
rw 		BK2F
rw 		BKF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MOE
rw 		AOE
rw 		BKP
rw 		BKE
rw 		OSSR
rw 		OSSI
rw 		LOCK
rw 		DTG
rw
Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are forced to idle level

OSSR

Bit 11: Off-state selection for Run mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are enabled with their inactive level

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

Allowed values:
0: DisabledIdle: OC/OCN are disabled or forced idle depending on OSSI
1: Enabled: OC/OCN are enabled if CCxE/CCxNE are set

BKF

Bits 16-19: Break filter.

BK2F

Bits 20-23: Break 2 filter.

BK2E

Bit 24: Break 2 enable.

BK2P

Bit 25: Break 2 polarity.

DCR

DMA control register

Offset: 0x48, reset: 0x00000000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DBL
rw 		DBA
rw
Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DMAB
rw
Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

CCMR3_Output

capture/compare mode register 3 (output mode)

Offset: 0x54, reset: 0x00000000, access: read-write

0/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
OC6M_3
rw 		OC5M_3
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OC6CE
rw 		OC6M
rw 		OC6PE
rw 		OC6FE
rw 		OC5CE
rw 		OC5M
rw 		OC5PE
rw 		OC5FE
rw
Toggle Fields.

OC5FE

Bit 2: Output compare 5 fast enable.

OC5PE

Bit 3: Output compare 5 preload enable.

OC5M

Bits 4-6: Output compare 5 mode.

OC5CE

Bit 7: Output compare 5 clear enable.

OC6FE

Bit 10: Output compare 6 fast enable.

OC6PE

Bit 11: Output compare 6 preload enable.

OC6M

Bits 12-14: Output compare 6 mode.

OC6CE

Bit 15: Output compare 6 clear enable.

OC5M_3

Bit 16: Outout Compare 5 mode bit 3.

OC6M_3

Bit 24: Outout Compare 6 mode bit 3.

CCR5

capture/compare register 5

Offset: 0x58, reset: 0x00000000, access: read-write

0/4 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
GC5C3
rw 		GC5C2
rw 		GC5C1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 5 value.

GC5C1

Bit 29: Group Channel 5 and Channel 1.

GC5C2

Bit 30: Group Channel 5 and Channel 2.

GC5C3

Bit 31: Group Channel 5 and Channel 3.

CCR6

capture/compare register 6

Offset: 0x5C, reset: 0x00000000, access: read-write

0/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CCR
rw
Toggle Fields.

CCR

Bits 0-15: Capture/Compare 6 value.

OR

option registers

Offset: 0x60, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TIM1_ETR_ADC4_RMP
rw 		TIM1_ETR_ADC1_RMP
rw
Toggle Fields.

TIM1_ETR_ADC1_RMP

Bits 0-1: TIM1_ETR_ADC1 remapping capability.

TIM1_ETR_ADC4_RMP

Bits 2-3: TIM1_ETR_ADC4 remapping capability.

TSC

0x40024000: Touch sensing controller

7/163 fields covered. Toggle Registers.

CR

control register

Offset: 0x0, reset: 0x00000000, access: read-write

0/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
CTPH
rw 		CTPL
rw 		SSD
rw 		SSE
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SSPSC
rw 		PGPSC
rw 		MCV
rw 		IODEF
rw 		SYNCPOL
rw 		AM
rw 		START
rw 		TSCE
rw
Toggle Fields.

TSCE

Bit 0: Touch sensing controller enable.

START

Bit 1: Start a new acquisition.

AM

Bit 2: Acquisition mode.

SYNCPOL

Bit 3: Synchronization pin polarity.

IODEF

Bit 4: I/O Default mode.

MCV

Bits 5-7: Max count value.

PGPSC

Bits 12-14: pulse generator prescaler.

SSPSC

Bit 15: Spread spectrum prescaler.

SSE

Bit 16: Spread spectrum enable.

SSD

Bits 17-23: Spread spectrum deviation.

CTPL

Bits 24-27: Charge transfer pulse low.

CTPH

Bits 28-31: Charge transfer pulse high.

IER

interrupt enable register

Offset: 0x4, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCEIE
rw 		EOAIE
rw
Toggle Fields.

EOAIE

Bit 0: End of acquisition interrupt enable.

MCEIE

Bit 1: Max count error interrupt enable.

ICR

interrupt clear register

Offset: 0x8, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCEIC
rw 		EOAIC
rw
Toggle Fields.

EOAIC

Bit 0: End of acquisition interrupt clear.

MCEIC

Bit 1: Max count error interrupt clear.

ISR

interrupt status register

Offset: 0xC, reset: 0x00000000, access: read-write

0/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MCEF
rw 		EOAF
rw
Toggle Fields.

EOAF

Bit 0: End of acquisition flag.

MCEF

Bit 1: Max count error flag.

IOHCR

I/O hysteresis control register

Offset: 0x10, reset: 0xFFFFFFFF, access: read-write

0/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
G8_IO4
rw 		G8_IO3
rw 		G8_IO2
rw 		G8_IO1
rw 		G7_IO4
rw 		G7_IO3
rw 		G7_IO2
rw 		G7_IO1
rw 		G6_IO4
rw 		G6_IO3
rw 		G6_IO2
rw 		G6_IO1
rw 		G5_IO4
rw 		G5_IO3
rw 		G5_IO2
rw 		G5_IO1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
G4_IO4
rw 		G4_IO3
rw 		G4_IO2
rw 		G4_IO1
rw 		G3_IO4
rw 		G3_IO3
rw 		G3_IO2
rw 		G3_IO1
rw 		G2_IO4
rw 		G2_IO3
rw 		G2_IO2
rw 		G2_IO1
rw 		G1_IO4
rw 		G1_IO3
rw 		G1_IO2
rw 		G1_IO1
rw
Toggle Fields.

G1_IO1

Bit 0: G1_IO1 Schmitt trigger hysteresis mode.

G1_IO2

Bit 1: G1_IO2 Schmitt trigger hysteresis mode.

G1_IO3

Bit 2: G1_IO3 Schmitt trigger hysteresis mode.

G1_IO4

Bit 3: G1_IO4 Schmitt trigger hysteresis mode.

G2_IO1

Bit 4: G2_IO1 Schmitt trigger hysteresis mode.

G2_IO2

Bit 5: G2_IO2 Schmitt trigger hysteresis mode.

G2_IO3

Bit 6: G2_IO3 Schmitt trigger hysteresis mode.

G2_IO4

Bit 7: G2_IO4 Schmitt trigger hysteresis mode.

G3_IO1

Bit 8: G3_IO1 Schmitt trigger hysteresis mode.

G3_IO2

Bit 9: G3_IO2 Schmitt trigger hysteresis mode.

G3_IO3

Bit 10: G3_IO3 Schmitt trigger hysteresis mode.

G3_IO4

Bit 11: G3_IO4 Schmitt trigger hysteresis mode.

G4_IO1

Bit 12: G4_IO1 Schmitt trigger hysteresis mode.

G4_IO2

Bit 13: G4_IO2 Schmitt trigger hysteresis mode.

G4_IO3

Bit 14: G4_IO3 Schmitt trigger hysteresis mode.

G4_IO4

Bit 15: G4_IO4 Schmitt trigger hysteresis mode.

G5_IO1

Bit 16: G5_IO1 Schmitt trigger hysteresis mode.

G5_IO2

Bit 17: G5_IO2 Schmitt trigger hysteresis mode.

G5_IO3

Bit 18: G5_IO3 Schmitt trigger hysteresis mode.

G5_IO4

Bit 19: G5_IO4 Schmitt trigger hysteresis mode.

G6_IO1

Bit 20: G6_IO1 Schmitt trigger hysteresis mode.

G6_IO2

Bit 21: G6_IO2 Schmitt trigger hysteresis mode.

G6_IO3

Bit 22: G6_IO3 Schmitt trigger hysteresis mode.

G6_IO4

Bit 23: G6_IO4 Schmitt trigger hysteresis mode.

G7_IO1

Bit 24: G7_IO1 Schmitt trigger hysteresis mode.

G7_IO2

Bit 25: G7_IO2 Schmitt trigger hysteresis mode.

G7_IO3

Bit 26: G7_IO3 Schmitt trigger hysteresis mode.

G7_IO4

Bit 27: G7_IO4 Schmitt trigger hysteresis mode.

G8_IO1

Bit 28: G8_IO1 Schmitt trigger hysteresis mode.

G8_IO2

Bit 29: G8_IO2 Schmitt trigger hysteresis mode.

G8_IO3

Bit 30: G8_IO3 Schmitt trigger hysteresis mode.

G8_IO4

Bit 31: G8_IO4 Schmitt trigger hysteresis mode.

IOASCR

I/O analog switch control register

Offset: 0x18, reset: 0x00000000, access: read-write

0/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
G8_IO4
rw 		G8_IO3
rw 		G8_IO2
rw 		G8_IO1
rw 		G7_IO4
rw 		G7_IO3
rw 		G7_IO2
rw 		G7_IO1
rw 		G6_IO4
rw 		G6_IO3
rw 		G6_IO2
rw 		G6_IO1
rw 		G5_IO4
rw 		G5_IO3
rw 		G5_IO2
rw 		G5_IO1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
G4_IO4
rw 		G4_IO3
rw 		G4_IO2
rw 		G4_IO1
rw 		G3_IO4
rw 		G3_IO3
rw 		G3_IO2
rw 		G3_IO1
rw 		G2_IO4
rw 		G2_IO3
rw 		G2_IO2
rw 		G2_IO1
rw 		G1_IO4
rw 		G1_IO3
rw 		G1_IO2
rw 		G1_IO1
rw
Toggle Fields.

G1_IO1

Bit 0: G1_IO1 analog switch enable.

G1_IO2

Bit 1: G1_IO2 analog switch enable.

G1_IO3

Bit 2: G1_IO3 analog switch enable.

G1_IO4

Bit 3: G1_IO4 analog switch enable.

G2_IO1

Bit 4: G2_IO1 analog switch enable.

G2_IO2

Bit 5: G2_IO2 analog switch enable.

G2_IO3

Bit 6: G2_IO3 analog switch enable.

G2_IO4

Bit 7: G2_IO4 analog switch enable.

G3_IO1

Bit 8: G3_IO1 analog switch enable.

G3_IO2

Bit 9: G3_IO2 analog switch enable.

G3_IO3

Bit 10: G3_IO3 analog switch enable.

G3_IO4

Bit 11: G3_IO4 analog switch enable.

G4_IO1

Bit 12: G4_IO1 analog switch enable.

G4_IO2

Bit 13: G4_IO2 analog switch enable.

G4_IO3

Bit 14: G4_IO3 analog switch enable.

G4_IO4

Bit 15: G4_IO4 analog switch enable.

G5_IO1

Bit 16: G5_IO1 analog switch enable.

G5_IO2

Bit 17: G5_IO2 analog switch enable.

G5_IO3

Bit 18: G5_IO3 analog switch enable.

G5_IO4

Bit 19: G5_IO4 analog switch enable.

G6_IO1

Bit 20: G6_IO1 analog switch enable.

G6_IO2

Bit 21: G6_IO2 analog switch enable.

G6_IO3

Bit 22: G6_IO3 analog switch enable.

G6_IO4

Bit 23: G6_IO4 analog switch enable.

G7_IO1

Bit 24: G7_IO1 analog switch enable.

G7_IO2

Bit 25: G7_IO2 analog switch enable.

G7_IO3

Bit 26: G7_IO3 analog switch enable.

G7_IO4

Bit 27: G7_IO4 analog switch enable.

G8_IO1

Bit 28: G8_IO1 analog switch enable.

G8_IO2

Bit 29: G8_IO2 analog switch enable.

G8_IO3

Bit 30: G8_IO3 analog switch enable.

G8_IO4

Bit 31: G8_IO4 analog switch enable.

IOSCR

I/O sampling control register

Offset: 0x20, reset: 0x00000000, access: read-write

0/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
G8_IO4
rw 		G8_IO3
rw 		G8_IO2
rw 		G8_IO1
rw 		G7_IO4
rw 		G7_IO3
rw 		G7_IO2
rw 		G7_IO1
rw 		G6_IO4
rw 		G6_IO3
rw 		G6_IO2
rw 		G6_IO1
rw 		G5_IO4
rw 		G5_IO3
rw 		G5_IO2
rw 		G5_IO1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
G4_IO4
rw 		G4_IO3
rw 		G4_IO2
rw 		G4_IO1
rw 		G3_IO4
rw 		G3_IO3
rw 		G3_IO2
rw 		G3_IO1
rw 		G2_IO4
rw 		G2_IO3
rw 		G2_IO2
rw 		G2_IO1
rw 		G1_IO4
rw 		G1_IO3
rw 		G1_IO2
rw 		G1_IO1
rw
Toggle Fields.

G1_IO1

Bit 0: G1_IO1 sampling mode.

G1_IO2

Bit 1: G1_IO2 sampling mode.

G1_IO3

Bit 2: G1_IO3 sampling mode.

G1_IO4

Bit 3: G1_IO4 sampling mode.

G2_IO1

Bit 4: G2_IO1 sampling mode.

G2_IO2

Bit 5: G2_IO2 sampling mode.

G2_IO3

Bit 6: G2_IO3 sampling mode.

G2_IO4

Bit 7: G2_IO4 sampling mode.

G3_IO1

Bit 8: G3_IO1 sampling mode.

G3_IO2

Bit 9: G3_IO2 sampling mode.

G3_IO3

Bit 10: G3_IO3 sampling mode.

G3_IO4

Bit 11: G3_IO4 sampling mode.

G4_IO1

Bit 12: G4_IO1 sampling mode.

G4_IO2

Bit 13: G4_IO2 sampling mode.

G4_IO3

Bit 14: G4_IO3 sampling mode.

G4_IO4

Bit 15: G4_IO4 sampling mode.

G5_IO1

Bit 16: G5_IO1 sampling mode.

G5_IO2

Bit 17: G5_IO2 sampling mode.

G5_IO3

Bit 18: G5_IO3 sampling mode.

G5_IO4

Bit 19: G5_IO4 sampling mode.

G6_IO1

Bit 20: G6_IO1 sampling mode.

G6_IO2

Bit 21: G6_IO2 sampling mode.

G6_IO3

Bit 22: G6_IO3 sampling mode.

G6_IO4

Bit 23: G6_IO4 sampling mode.

G7_IO1

Bit 24: G7_IO1 sampling mode.

G7_IO2

Bit 25: G7_IO2 sampling mode.

G7_IO3

Bit 26: G7_IO3 sampling mode.

G7_IO4

Bit 27: G7_IO4 sampling mode.

G8_IO1

Bit 28: G8_IO1 sampling mode.

G8_IO2

Bit 29: G8_IO2 sampling mode.

G8_IO3

Bit 30: G8_IO3 sampling mode.

G8_IO4

Bit 31: G8_IO4 sampling mode.

IOCCR

I/O channel control register

Offset: 0x28, reset: 0x00000000, access: read-write

0/32 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
G8_IO4
rw 		G8_IO3
rw 		G8_IO2
rw 		G8_IO1
rw 		G7_IO4
rw 		G7_IO3
rw 		G7_IO2
rw 		G7_IO1
rw 		G6_IO4
rw 		G6_IO3
rw 		G6_IO2
rw 		G6_IO1
rw 		G5_IO4
rw 		G5_IO3
rw 		G5_IO2
rw 		G5_IO1
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
G4_IO4
rw 		G4_IO3
rw 		G4_IO2
rw 		G4_IO1
rw 		G3_IO4
rw 		G3_IO3
rw 		G3_IO2
rw 		G3_IO1
rw 		G2_IO4
rw 		G2_IO3
rw 		G2_IO2
rw 		G2_IO1
rw 		G1_IO4
rw 		G1_IO3
rw 		G1_IO2
rw 		G1_IO1
rw
Toggle Fields.

G1_IO1

Bit 0: G1_IO1 channel mode.

G1_IO2

Bit 1: G1_IO2 channel mode.

G1_IO3

Bit 2: G1_IO3 channel mode.

G1_IO4

Bit 3: G1_IO4 channel mode.

G2_IO1

Bit 4: G2_IO1 channel mode.

G2_IO2

Bit 5: G2_IO2 channel mode.

G2_IO3

Bit 6: G2_IO3 channel mode.

G2_IO4

Bit 7: G2_IO4 channel mode.

G3_IO1

Bit 8: G3_IO1 channel mode.

G3_IO2

Bit 9: G3_IO2 channel mode.

G3_IO3

Bit 10: G3_IO3 channel mode.

G3_IO4

Bit 11: G3_IO4 channel mode.

G4_IO1

Bit 12: G4_IO1 channel mode.

G4_IO2

Bit 13: G4_IO2 channel mode.

G4_IO3

Bit 14: G4_IO3 channel mode.

G4_IO4

Bit 15: G4_IO4 channel mode.

G5_IO1

Bit 16: G5_IO1 channel mode.

G5_IO2

Bit 17: G5_IO2 channel mode.

G5_IO3

Bit 18: G5_IO3 channel mode.

G5_IO4

Bit 19: G5_IO4 channel mode.

G6_IO1

Bit 20: G6_IO1 channel mode.

G6_IO2

Bit 21: G6_IO2 channel mode.

G6_IO3

Bit 22: G6_IO3 channel mode.

G6_IO4

Bit 23: G6_IO4 channel mode.

G7_IO1

Bit 24: G7_IO1 channel mode.

G7_IO2

Bit 25: G7_IO2 channel mode.

G7_IO3

Bit 26: G7_IO3 channel mode.

G7_IO4

Bit 27: G7_IO4 channel mode.

G8_IO1

Bit 28: G8_IO1 channel mode.

G8_IO2

Bit 29: G8_IO2 channel mode.

G8_IO3

Bit 30: G8_IO3 channel mode.

G8_IO4

Bit 31: G8_IO4 channel mode.

IOGCSR

I/O group control status register

Offset: 0x30, reset: 0x00000000, access: Unspecified

6/16 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
G8S
rw 		G7S
rw 		G6S
r 		G5S
r 		G4S
r 		G3S
r 		G2S
r 		G1S
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
G8E
rw 		G7E
rw 		G6E
rw 		G5E
rw 		G4E
rw 		G3E
rw 		G2E
rw 		G1E
rw
Toggle Fields.

G1E

Bit 0: Analog I/O group x enable.

G2E

Bit 1: Analog I/O group x enable.

G3E

Bit 2: Analog I/O group x enable.

G4E

Bit 3: Analog I/O group x enable.

G5E

Bit 4: Analog I/O group x enable.

G6E

Bit 5: Analog I/O group x enable.

G7E

Bit 6: Analog I/O group x enable.

G8E

Bit 7: Analog I/O group x enable.

G1S

Bit 16: Analog I/O group x status.

G2S

Bit 17: Analog I/O group x status.

G3S

Bit 18: Analog I/O group x status.

G4S

Bit 19: Analog I/O group x status.

G5S

Bit 20: Analog I/O group x status.

G6S

Bit 21: Analog I/O group x status.

G7S

Bit 22: Analog I/O group x status.

G8S

Bit 23: Analog I/O group x status.

IOG%sCR

I/O group x counter register

Offset: 0x34, reset: 0x00000000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CNT
r
Toggle Fields.

CNT

Bits 0-13: Counter value.

UART4

0x40004C00: Universal synchronous asynchronous receiver transmitter

103/103 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

20/20 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
EOBIE
rw 		RTOIE
rw 		DEAT
rw 		DEDT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OVER8
rw 		CMIE
rw 		MME
rw 		M
rw 		WAKE
rw 		PCE
rw 		PS
rw 		PEIE
rw 		TXEIE
rw 		TCIE
rw 		RXNEIE
rw 		IDLEIE
rw 		TE
rw 		RE
rw 		UESM
rw 		UE
rw
Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADD
rw 		RTOEN
rw 		ABRMOD
rw 		ABREN
rw 		MSBFIRST
rw 		DATAINV
rw 		TXINV
rw 		RXINV
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SWAP
rw 		LINEN
rw 		STOP
rw 		CLKEN
rw 		CPOL
rw 		CPHA
rw 		LBCL
rw 		LBDIE
rw 		LBDL
rw 		ADDM7
rw
Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUFIE
rw 		WUS
rw 		SCARCNT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DEP
rw 		DEM
rw 		DDRE
rw 		OVRDIS
rw 		ONEBIT
rw 		CTSIE
rw 		CTSE
rw 		RTSE
rw 		DMAT
rw 		DMAR
rw 		SCEN
rw 		NACK
rw 		HDSEL
rw 		IRLP
rw 		IREN
rw 		EIE
rw
Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BRR
rw
Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
GT
rw 		PSC
rw
Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BLEN
rw 		RTO
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RTO
rw
Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TXFRQ
rw 		RXFRQ
rw 		MMRQ
rw 		SBKRQ
rw 		ABRRQ
rw
Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
REACK
r 		TEACK
r 		WUF
r 		RWU
r 		SBKF
r 		CMF
r 		BUSY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ABRF
r 		ABRE
r 		EOBF
r 		RTOF
r 		CTS
r 		CTSIF
r 		LBDF
r 		TXE
r 		TC
r 		RXNE
r 		IDLE
r 		ORE
r 		NF
r 		FE
r 		PE
r
Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUCF
rw 		CMCF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EOBCF
rw 		RTOCF
rw 		CTSCF
rw 		LBDCF
rw 		TCCF
rw 		IDLECF
rw 		ORECF
rw 		NCF
rw 		FECF
rw 		PECF
rw
Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDR
r
Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDR
rw
Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

UART5

0x40005000: Universal synchronous asynchronous receiver transmitter

103/103 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

20/20 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
EOBIE
rw 		RTOIE
rw 		DEAT
rw 		DEDT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OVER8
rw 		CMIE
rw 		MME
rw 		M
rw 		WAKE
rw 		PCE
rw 		PS
rw 		PEIE
rw 		TXEIE
rw 		TCIE
rw 		RXNEIE
rw 		IDLEIE
rw 		TE
rw 		RE
rw 		UESM
rw 		UE
rw
Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADD
rw 		RTOEN
rw 		ABRMOD
rw 		ABREN
rw 		MSBFIRST
rw 		DATAINV
rw 		TXINV
rw 		RXINV
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SWAP
rw 		LINEN
rw 		STOP
rw 		CLKEN
rw 		CPOL
rw 		CPHA
rw 		LBCL
rw 		LBDIE
rw 		LBDL
rw 		ADDM7
rw
Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUFIE
rw 		WUS
rw 		SCARCNT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DEP
rw 		DEM
rw 		DDRE
rw 		OVRDIS
rw 		ONEBIT
rw 		CTSIE
rw 		CTSE
rw 		RTSE
rw 		DMAT
rw 		DMAR
rw 		SCEN
rw 		NACK
rw 		HDSEL
rw 		IRLP
rw 		IREN
rw 		EIE
rw
Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BRR
rw
Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
GT
rw 		PSC
rw
Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BLEN
rw 		RTO
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RTO
rw
Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TXFRQ
rw 		RXFRQ
rw 		MMRQ
rw 		SBKRQ
rw 		ABRRQ
rw
Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
REACK
r 		TEACK
r 		WUF
r 		RWU
r 		SBKF
r 		CMF
r 		BUSY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ABRF
r 		ABRE
r 		EOBF
r 		RTOF
r 		CTS
r 		CTSIF
r 		LBDF
r 		TXE
r 		TC
r 		RXNE
r 		IDLE
r 		ORE
r 		NF
r 		FE
r 		PE
r
Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUCF
rw 		CMCF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EOBCF
rw 		RTOCF
rw 		CTSCF
rw 		LBDCF
rw 		TCCF
rw 		IDLECF
rw 		ORECF
rw 		NCF
rw 		FECF
rw 		PECF
rw
Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDR
r
Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDR
rw
Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

USART1

0x40013800: Universal synchronous asynchronous receiver transmitter

103/103 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

20/20 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
EOBIE
rw 		RTOIE
rw 		DEAT
rw 		DEDT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OVER8
rw 		CMIE
rw 		MME
rw 		M
rw 		WAKE
rw 		PCE
rw 		PS
rw 		PEIE
rw 		TXEIE
rw 		TCIE
rw 		RXNEIE
rw 		IDLEIE
rw 		TE
rw 		RE
rw 		UESM
rw 		UE
rw
Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADD
rw 		RTOEN
rw 		ABRMOD
rw 		ABREN
rw 		MSBFIRST
rw 		DATAINV
rw 		TXINV
rw 		RXINV
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SWAP
rw 		LINEN
rw 		STOP
rw 		CLKEN
rw 		CPOL
rw 		CPHA
rw 		LBCL
rw 		LBDIE
rw 		LBDL
rw 		ADDM7
rw
Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUFIE
rw 		WUS
rw 		SCARCNT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DEP
rw 		DEM
rw 		DDRE
rw 		OVRDIS
rw 		ONEBIT
rw 		CTSIE
rw 		CTSE
rw 		RTSE
rw 		DMAT
rw 		DMAR
rw 		SCEN
rw 		NACK
rw 		HDSEL
rw 		IRLP
rw 		IREN
rw 		EIE
rw
Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BRR
rw
Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
GT
rw 		PSC
rw
Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BLEN
rw 		RTO
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RTO
rw
Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TXFRQ
rw 		RXFRQ
rw 		MMRQ
rw 		SBKRQ
rw 		ABRRQ
rw
Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
REACK
r 		TEACK
r 		WUF
r 		RWU
r 		SBKF
r 		CMF
r 		BUSY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ABRF
r 		ABRE
r 		EOBF
r 		RTOF
r 		CTS
r 		CTSIF
r 		LBDF
r 		TXE
r 		TC
r 		RXNE
r 		IDLE
r 		ORE
r 		NF
r 		FE
r 		PE
r
Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUCF
rw 		CMCF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EOBCF
rw 		RTOCF
rw 		CTSCF
rw 		LBDCF
rw 		TCCF
rw 		IDLECF
rw 		ORECF
rw 		NCF
rw 		FECF
rw 		PECF
rw
Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDR
r
Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDR
rw
Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

USART2

0x40004400: Universal synchronous asynchronous receiver transmitter

103/103 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

20/20 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
EOBIE
rw 		RTOIE
rw 		DEAT
rw 		DEDT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OVER8
rw 		CMIE
rw 		MME
rw 		M
rw 		WAKE
rw 		PCE
rw 		PS
rw 		PEIE
rw 		TXEIE
rw 		TCIE
rw 		RXNEIE
rw 		IDLEIE
rw 		TE
rw 		RE
rw 		UESM
rw 		UE
rw
Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADD
rw 		RTOEN
rw 		ABRMOD
rw 		ABREN
rw 		MSBFIRST
rw 		DATAINV
rw 		TXINV
rw 		RXINV
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SWAP
rw 		LINEN
rw 		STOP
rw 		CLKEN
rw 		CPOL
rw 		CPHA
rw 		LBCL
rw 		LBDIE
rw 		LBDL
rw 		ADDM7
rw
Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUFIE
rw 		WUS
rw 		SCARCNT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DEP
rw 		DEM
rw 		DDRE
rw 		OVRDIS
rw 		ONEBIT
rw 		CTSIE
rw 		CTSE
rw 		RTSE
rw 		DMAT
rw 		DMAR
rw 		SCEN
rw 		NACK
rw 		HDSEL
rw 		IRLP
rw 		IREN
rw 		EIE
rw
Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BRR
rw
Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
GT
rw 		PSC
rw
Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BLEN
rw 		RTO
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RTO
rw
Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TXFRQ
rw 		RXFRQ
rw 		MMRQ
rw 		SBKRQ
rw 		ABRRQ
rw
Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
REACK
r 		TEACK
r 		WUF
r 		RWU
r 		SBKF
r 		CMF
r 		BUSY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ABRF
r 		ABRE
r 		EOBF
r 		RTOF
r 		CTS
r 		CTSIF
r 		LBDF
r 		TXE
r 		TC
r 		RXNE
r 		IDLE
r 		ORE
r 		NF
r 		FE
r 		PE
r
Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUCF
rw 		CMCF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EOBCF
rw 		RTOCF
rw 		CTSCF
rw 		LBDCF
rw 		TCCF
rw 		IDLECF
rw 		ORECF
rw 		NCF
rw 		FECF
rw 		PECF
rw
Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDR
r
Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDR
rw
Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

USART3

0x40004800: Universal synchronous asynchronous receiver transmitter

103/103 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

20/20 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
EOBIE
rw 		RTOIE
rw 		DEAT
rw 		DEDT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
OVER8
rw 		CMIE
rw 		MME
rw 		M
rw 		WAKE
rw 		PCE
rw 		PS
rw 		PEIE
rw 		TXEIE
rw 		TCIE
rw 		RXNEIE
rw 		IDLEIE
rw 		TE
rw 		RE
rw 		UESM
rw 		UE
rw
Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
ADD
rw 		RTOEN
rw 		ABRMOD
rw 		ABREN
rw 		MSBFIRST
rw 		DATAINV
rw 		TXINV
rw 		RXINV
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
SWAP
rw 		LINEN
rw 		STOP
rw 		CLKEN
rw 		CPOL
rw 		CPHA
rw 		LBCL
rw 		LBDIE
rw 		LBDL
rw 		ADDM7
rw
Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUFIE
rw 		WUS
rw 		SCARCNT
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DEP
rw 		DEM
rw 		DDRE
rw 		OVRDIS
rw 		ONEBIT
rw 		CTSIE
rw 		CTSE
rw 		RTSE
rw 		DMAT
rw 		DMAR
rw 		SCEN
rw 		NACK
rw 		HDSEL
rw 		IRLP
rw 		IREN
rw 		EIE
rw
Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BRR
rw
Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
GT
rw 		PSC
rw
Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
BLEN
rw 		RTO
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RTO
rw
Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TXFRQ
rw 		RXFRQ
rw 		MMRQ
rw 		SBKRQ
rw 		ABRRQ
rw
Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
REACK
r 		TEACK
r 		WUF
r 		RWU
r 		SBKF
r 		CMF
r 		BUSY
r
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
ABRF
r 		ABRE
r 		EOBF
r 		RTOF
r 		CTS
r 		CTSIF
r 		LBDF
r 		TXE
r 		TC
r 		RXNE
r 		IDLE
r 		ORE
r 		NF
r 		FE
r 		PE
r
Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
WUCF
rw 		CMCF
rw
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EOBCF
rw 		RTOCF
rw 		CTSCF
rw 		LBDCF
rw 		TCCF
rw 		IDLECF
rw 		ORECF
rw 		NCF
rw 		FECF
rw 		PECF
rw
Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RDR
r
Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
TDR
rw
Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

USB

0x40005C00: Universal serial bus full-speed device interface

71/117 fields covered. Toggle Registers.

EP0R

endpoint 0 register

Offset: 0x0, reset: 0x00000000, access: Unspecified

5/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR_RX
rw 		DTOG_RX
rw 		STAT_RX
rw 		SETUP
r 		EP_TYPE
rw 		EP_KIND
rw 		CTR_TX
rw 		DTOG_TX
rw 		STAT_TX
rw 		EA
rw
Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP1R

endpoint 1 register

Offset: 0x4, reset: 0x00000000, access: Unspecified

5/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR_RX
rw 		DTOG_RX
rw 		STAT_RX
rw 		SETUP
r 		EP_TYPE
rw 		EP_KIND
rw 		CTR_TX
rw 		DTOG_TX
rw 		STAT_TX
rw 		EA
rw
Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP2R

endpoint 2 register

Offset: 0x8, reset: 0x00000000, access: Unspecified

5/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR_RX
rw 		DTOG_RX
rw 		STAT_RX
rw 		SETUP
r 		EP_TYPE
rw 		EP_KIND
rw 		CTR_TX
rw 		DTOG_TX
rw 		STAT_TX
rw 		EA
rw
Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP3R

endpoint 3 register

Offset: 0xC, reset: 0x00000000, access: Unspecified

5/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR_RX
rw 		DTOG_RX
rw 		STAT_RX
rw 		SETUP
r 		EP_TYPE
rw 		EP_KIND
rw 		CTR_TX
rw 		DTOG_TX
rw 		STAT_TX
rw 		EA
rw
Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP4R

endpoint 4 register

Offset: 0x10, reset: 0x00000000, access: Unspecified

5/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR_RX
rw 		DTOG_RX
rw 		STAT_RX
rw 		SETUP
r 		EP_TYPE
rw 		EP_KIND
rw 		CTR_TX
rw 		DTOG_TX
rw 		STAT_TX
rw 		EA
rw
Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP5R

endpoint 5 register

Offset: 0x14, reset: 0x00000000, access: Unspecified

5/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR_RX
rw 		DTOG_RX
rw 		STAT_RX
rw 		SETUP
r 		EP_TYPE
rw 		EP_KIND
rw 		CTR_TX
rw 		DTOG_TX
rw 		STAT_TX
rw 		EA
rw
Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP6R

endpoint 6 register

Offset: 0x18, reset: 0x00000000, access: Unspecified

5/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR_RX
rw 		DTOG_RX
rw 		STAT_RX
rw 		SETUP
r 		EP_TYPE
rw 		EP_KIND
rw 		CTR_TX
rw 		DTOG_TX
rw 		STAT_TX
rw 		EA
rw
Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP7R

endpoint 7 register

Offset: 0x1C, reset: 0x00000000, access: Unspecified

5/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR_RX
rw 		DTOG_RX
rw 		STAT_RX
rw 		SETUP
r 		EP_TYPE
rw 		EP_KIND
rw 		CTR_TX
rw 		DTOG_TX
rw 		STAT_TX
rw 		EA
rw
Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

CNTR

control register

Offset: 0x40, reset: 0x00000003, access: read-write

13/13 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTRM
rw 		PMAOVRM
rw 		ERRM
rw 		WKUPM
rw 		SUSPM
rw 		RESETM
rw 		SOFM
rw 		ESOFM
rw 		RESUME
rw 		FSUSP
rw 		LPMODE
rw 		PDWN
rw 		FRES
rw
Toggle Fields.

FRES

Bit 0: Force USB Reset.

Allowed values:
0: NoReset: Clear USB reset
1: Reset: Force a reset of the USB peripheral, exactly like a RESET signaling on the USB

PDWN

Bit 1: Power down.

Allowed values:
0: Disabled: No power down
1: Enabled: Enter power down mode

LPMODE

Bit 2: Low-power mode.

Allowed values:
0: Disabled: No low-power mode
1: Enabled: Enter low-power mode

FSUSP

Bit 3: Force suspend.

Allowed values:
0: NoEffect: No effect
1: Suspend: Enter suspend mode. Clocks and static power dissipation in the analog transceiver are left unaffected

RESUME

Bit 4: Resume request.

Allowed values:
1: Requested: Resume requested

ESOFM

Bit 8: Expected start of frame interrupt mask.

Allowed values:
0: Disabled: ESOF Interrupt disabled
1: Enabled: ESOF Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

SOFM

Bit 9: Start of frame interrupt mask.

Allowed values:
0: Disabled: SOF Interrupt disabled
1: Enabled: SOF Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

RESETM

Bit 10: USB reset interrupt mask.

Allowed values:
0: Disabled: RESET Interrupt disabled
1: Enabled: RESET Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

SUSPM

Bit 11: Suspend mode interrupt mask.

Allowed values:
0: Disabled: Suspend Mode Request SUSP Interrupt disabled
1: Enabled: SUSP Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

WKUPM

Bit 12: Wakeup interrupt mask.

Allowed values:
0: Disabled: WKUP Interrupt disabled
1: Enabled: WKUP Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

ERRM

Bit 13: Error interrupt mask.

Allowed values:
0: Disabled: ERR Interrupt disabled
1: Enabled: ERR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

PMAOVRM

Bit 14: Packet memory area over / underrun interrupt mask.

Allowed values:
0: Disabled: PMAOVR Interrupt disabled
1: Enabled: PMAOVR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

CTRM

Bit 15: Correct transfer interrupt mask.

Allowed values:
0: Disabled: Correct Transfer (CTR) Interrupt disabled
1: Enabled: CTR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

ISTR

interrupt status register

Offset: 0x44, reset: 0x00000000, access: Unspecified

10/10 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
CTR
r 		PMAOVR
rw 		ERR
rw 		WKUP
rw 		SUSP
rw 		RESET
rw 		SOF
rw 		ESOF
rw 		DIR
r 		EP_ID
r
Toggle Fields.

EP_ID

Bits 0-3: Endpoint Identifier.

Allowed values: 0-15

DIR

Bit 4: Direction of transaction.

Allowed values:
0: To: data transmitted by the USB peripheral to the host PC
1: From: data received by the USB peripheral from the host PC

ESOF

Bit 8: Expected start frame.

Allowed values:
1: ExpectedStartOfFrame: an SOF packet is expected but not received

SOF

Bit 9: start of frame.

Allowed values:
1: StartOfFrame: beginning of a new USB frame and it is set when a SOF packet arrives through the USB bus

RESET

Bit 10: reset request.

Allowed values:
1: Reset: peripheral detects an active USB RESET signal at its inputs

SUSP

Bit 11: Suspend mode request.

Allowed values:
1: Suspend: no traffic has been received for 3 ms, indicating a suspend mode request from the USB bus

WKUP

Bit 12: Wakeup.

Allowed values:
1: Wakeup: activity is detected that wakes up the USB peripheral

ERR

Bit 13: Error.

Allowed values:
1: Error: One of No ANSwer, Cyclic Redundancy Check, Bit Stuffing or Framing format Violation error occurred

PMAOVR

Bit 14: Packet memory area over / underrun.

Allowed values:
1: Overrun: microcontroller has not been able to respond in time to an USB memory request

CTR

Bit 15: Correct transfer.

Allowed values:
1: Completed: endpoint has successfully completed a transaction

FNR

frame number register

Offset: 0x48, reset: 0x0000, access: read-only

5/5 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
RXDP
r 		RXDM
r 		LCK
r 		LSOF
r 		FN
r
Toggle Fields.

FN

Bits 0-10: Frame number.

Allowed values: 0-2047

LSOF

Bits 11-12: Lost SOF.

Allowed values: 0-3

LCK

Bit 13: Locked.

Allowed values:
1: Locked: the frame timer remains in this state until an USB reset or USB suspend event occurs

RXDM

Bit 14: Receive data - line status.

Allowed values:
1: Received: received data minus upstream port data line

RXDP

Bit 15: Receive data + line status.

Allowed values:
1: Received: received data plus upstream port data line

DADDR

device address

Offset: 0x4C, reset: 0x0000, access: read-write

2/8 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EF
rw 		ADD6
rw 		ADD5
rw 		ADD4
rw 		ADD3
rw 		ADD2
rw 		ADD1
rw 		ADD
rw
Toggle Fields.

ADD

Bit 0: Device address.

Allowed values: 0-127

ADD1

Bit 1: Device address.

ADD2

Bit 2: Device address.

ADD3

Bit 3: Device address.

ADD4

Bit 4: Device address.

ADD5

Bit 5: Device address.

ADD6

Bit 6: Device address.

EF

Bit 7: Enable function.

Allowed values:
0: Disabled: USB device disabled
1: Enabled: USB device enabled

BTABLE

Buffer table address

Offset: 0x50, reset: 0x0000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
BTABLE
rw
Toggle Fields.

BTABLE

Bits 3-15: Buffer table.

Allowed values: 0-8191

WWDG

0x40002C00: Window watchdog

6/6 fields covered. Toggle Registers.

CR

Control register

Offset: 0x0, reset: 0x0000007F, access: read-write

2/2 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
WDGA
rw 		T
rw
Toggle Fields.

T

Bits 0-6: 7-bit counter.

Allowed values: 0-127

WDGA

Bit 7: Activation bit.

Allowed values:
0: Disabled: Watchdog disabled
1: Enabled: Watchdog enabled

CFR

Configuration register

Offset: 0x4, reset: 0x0000007F, access: read-write

3/3 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EWI
rw 		WDGTB
rw 		W
rw
Toggle Fields.

W

Bits 0-6: 7-bit window value.

Allowed values: 0-127

WDGTB

Bits 7-8: Timer base.

Allowed values:
0: Div1: Counter clock (PCLK1 div 4096) div 1
1: Div2: Counter clock (PCLK1 div 4096) div 2
2: Div4: Counter clock (PCLK1 div 4096) div 4
3: Div8: Counter clock (PCLK1 div 4096) div 8

EWI

Bit 9: Early wakeup interrupt.

Allowed values:
1: Enable: interrupt occurs whenever the counter reaches the value 0x40

SR

Status register

Offset: 0x8, reset: 0x00000000, access: read-write

1/1 fields covered.

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
EWIF
rw
Toggle Fields.

EWIF

Bit 0: Early wakeup interrupt flag.

Allowed values:
1: Pending: The EWI Interrupt Service Routine has been triggered
0: Finished: The EWI Interrupt Service Routine has been serviced